At this point, you should be able to do most of the day-to-day tasks for which you’ll be using Git. However, in order to do any collaboration in Git, you’ll need to have a remote Git repository. Although you can technically push changes to and pull changes from individuals’ repositories, doing so is discouraged because you can fairly easily confuse what they’re working on if you’re not careful. Furthermore, you want your collaborators to be able to access the repository even if your computer is offline — having a more reliable common repository is often useful. Therefore, the preferred method for collaborating with someone is to set up an intermediate repository that you both have access to, and push to and pull from that. We’ll refer to this repository as a "Git server"; but you’ll notice that it generally takes a tiny amount of resources to host a Git repository, so you’ll rarely need to use an entire server for it.
Running a Git server is simple. First, you choose which protocols you want your server to communicate with. The first section of this chapter will cover the available protocols and the pros and cons of each. The next sections will explain some typical setups using those protocols and how to get your server running with them. Last, we’ll go over a few hosted options, if you don’t mind hosting your code on someone else’s server and don’t want to go through the hassle of setting up and maintaining your own server.
If you have no interest in running your own server, you can skip to the last section of the chapter to see some options for setting up a hosted account and then move on to the next chapter, where we discuss the various ins and outs of working in a distributed source control environment.
A remote repository is generally a bare repository — a Git repository that has no working directory. Because the repository is only used as a collaboration point, there is no reason to have a snapshot checked out on disk; it’s just the Git data. In the simplest terms, a bare repository is the contents of your project’s
.git directory and nothing else.
Git can use four major network protocols to transfer data: Local, Secure Shell (SSH), Git, and HTTP. Here we’ll discuss what they are and in what basic circumstances you would want (or not want) to use them.
It’s important to note that with the exception of the HTTP protocols, all of these require Git to be installed and working on the server.
The most basic is the Local protocol, in which the remote repository is in another directory on disk. This is often used if everyone on your team has access to a shared filesystem such as an NFS mount, or in the less likely case that everyone logs in to the same computer. The latter wouldn’t be ideal, because all your code repository instances would reside on the same computer, making a catastrophic loss much more likely.
If you have a shared mounted filesystem, then you can clone, push to, and pull from a local file-based repository. To clone a repository like this or to add one as a remote to an existing project, use the path to the repository as the URL. For example, to clone a local repository, you can run something like this:
$ git clone /opt/git/project.git
Or you can do this:
$ git clone file:///opt/git/project.git
Git operates slightly differently if you explicitly specify
file:// at the beginning of the URL. If you just specify the path, Git tries to use hardlinks or directly copy the files it needs. If you specify
file://, Git fires up the processes that it normally uses to transfer data over a network which is generally a lot less efficient method of transferring the data. The main reason to specify the
file:// prefix is if you want a clean copy of the repository with extraneous references or objects left out — generally after an import from another version-control system or something similar (see Chapter 9 for maintenance tasks). We’ll use the normal path here because doing so is almost always faster.
To add a local repository to an existing Git project, you can run something like this:
$ git remote add local_proj /opt/git/project.git
Then, you can push to and pull from that remote as though you were doing so over a network.
The pros of file-based repositories are that they’re simple and they use existing file permissions and network access. If you already have a shared filesystem to which your whole team has access, setting up a repository is very easy. You stick the bare repository copy somewhere everyone has shared access to and set the read/write permissions as you would for any other shared directory. We’ll discuss how to export a bare repository copy for this purpose in the next section, “Getting Git on a Server.”
This is also a nice option for quickly grabbing work from someone else’s working repository. If you and a co-worker are working on the same project and they want you to check something out, running a command like
git pull /home/john/project is often easier than them pushing to a remote server and you pulling down.
The cons of this method are that shared access is generally more difficult to set up and reach from multiple locations than basic network access. If you want to push from your laptop when you’re at home, you have to mount the remote disk, which can be difficult and slow compared to network-based access.
It’s also important to mention that this isn’t necessarily the fastest option if you’re using a shared mount of some kind. A local repository is fast only if you have fast access to the data. A repository on NFS is often slower than the repository over SSH on the same server, allowing Git to run off local disks on each system.
Probably the most common transport protocol for Git is SSH. This is because SSH access to servers is already set up in most places — and if it isn’t, it’s easy to do. SSH is also the only network-based protocol that you can easily read from and write to. The other two network protocols (HTTP and Git) are generally read-only, so even if you have them available for the unwashed masses, you still need SSH for your own write commands. SSH is also an authenticated network protocol; and because it’s ubiquitous, it’s generally easy to set up and use.
To clone a Git repository over SSH, you can specify ssh:// URL like this:
$ git clone ssh://user@server:project.git
Or you can not specify a protocol — Git assumes SSH if you aren’t explicit:
$ git clone user@server:project.git
You can also not specify a user, and Git assumes the user you’re currently logged in as.
The pros of using SSH are many. First, you basically have to use it if you want authenticated write access to your repository over a network. Second, SSH is relatively easy to set up — SSH daemons are commonplace, many network admins have experience with them, and many OS distributions are set up with them or have tools to manage them. Next, access over SSH is secure — all data transfer is encrypted and authenticated. Last, like the Git and Local protocols, SSH is efficient, making the data as compact as possible before transferring it.
The negative aspect of SSH is that you can’t serve anonymous access of your repository over it. People must have access to your machine over SSH to access it, even in a read-only capacity, which doesn’t make SSH access conducive to open source projects. If you’re using it only within your corporate network, SSH may be the only protocol you need to deal with. If you want to allow anonymous read-only access to your projects, you’ll have to set up SSH for you to push over but something else for others to pull over.
Next is the Git protocol. This is a special daemon that comes packaged with Git; it listens on a dedicated port (9418) that provides a service similar to the SSH protocol, but with absolutely no authentication. In order for a repository to be served over the Git protocol, you must create the
git-export-daemon-ok file — the daemon won’t serve a repository without that file in it — but other than that there is no security. Either the Git repository is available for everyone to clone or it isn’t. This means that there is generally no pushing over this protocol. You can enable push access; but given the lack of authentication, if you turn on push access, anyone on the internet who finds your project’s URL could push to your project. Suffice it to say that this is rare.
The Git protocol is the fastest transfer protocol available. If you’re serving a lot of traffic for a public project or serving a very large project that doesn’t require user authentication for read access, it’s likely that you’ll want to set up a Git daemon to serve your project. It uses the same data-transfer mechanism as the SSH protocol but without the encryption and authentication overhead.
The downside of the Git protocol is the lack of authentication. It’s generally undesirable for the Git protocol to be the only access to your project. Generally, you’ll pair it with SSH access for the few developers who have push (write) access and have everyone else use
git:// for read-only access.
It’s also probably the most difficult protocol to set up. It must run its own daemon, which is custom — we’ll look at setting one up in the “Gitosis” section of this chapter — it requires
xinetd configuration or the like, which isn’t always a walk in the park. It also requires firewall access to port 9418, which isn’t a standard port that corporate firewalls always allow. Behind big corporate firewalls, this obscure port is commonly blocked.
Last we have the HTTP protocol. The beauty of the HTTP or HTTPS protocol is the simplicity of setting it up. Basically, all you have to do is put the bare Git repository under your HTTP document root and set up a specific
post-update hook, and you’re done (See Chapter 7 for details on Git hooks). At that point, anyone who can access the web server under which you put the repository can also clone your repository. To allow read access to your repository over HTTP, do something like this:
$ cd /var/www/htdocs/ $ git clone --bare /path/to/git_project gitproject.git $ cd gitproject.git $ mv hooks/post-update.sample hooks/post-update $ chmod a+x hooks/post-update
That’s all. The
post-update hook that comes with Git by default runs the appropriate command (
git update-server-info) to make HTTP fetching and cloning work properly. This command is run when you push to this repository over SSH; then, other people can clone via something like
$ git clone http://example.com/gitproject.git
In this particular case, we’re using the
/var/www/htdocs path that is common for Apache setups, but you can use any static web server — just put the bare repository in its path. The Git data is served as basic static files (see Chapter 9 for details about exactly how it’s served).
It’s possible to make Git push over HTTP as well, although that technique isn’t as widely used and requires you to set up complex WebDAV requirements. Because it’s rarely used, we won’t cover it in this book. If you’re interested in using the HTTP-push protocols, you can read about preparing a repository for this purpose at
http://www.kernel.org/pub/software/scm/git/docs/howto/setup-git-server-over-http.txt. One nice thing about making Git push over HTTP is that you can use any WebDAV server, without specific Git features; so, you can use this functionality if your web-hosting provider supports WebDAV for writing updates to your web site.
The upside of using the HTTP protocol is that it’s easy to set up. Running the handful of required commands gives you a simple way to give the world read access to your Git repository. It takes only a few minutes to do. The HTTP protocol also isn’t very resource intensive on your server. Because it generally uses a static HTTP server to serve all the data, a normal Apache server can serve thousands of files per second on average — it’s difficult to overload even a small server.
You can also serve your repositories read-only over HTTPS, which means you can encrypt the content transfer; or you can go so far as to make the clients use specific signed SSL certificates. Generally, if you’re going to these lengths, it’s easier to use SSH public keys; but it may be a better solution in your specific case to use signed SSL certificates or other HTTP-based authentication methods for read-only access over HTTPS.
Another nice thing is that HTTP is such a commonly used protocol that corporate firewalls are often set up to allow traffic through this port.
The downside of serving your repository over HTTP is that it’s relatively inefficient for the client. It generally takes a lot longer to clone or fetch from the repository, and you often have a lot more network overhead and transfer volume over HTTP than with any of the other network protocols. Because it’s not as intelligent about transferring only the data you need — there is no dynamic work on the part of the server in these transactions — the HTTP protocol is often referred to as a dumb protocol. For more information about the differences in efficiency between the HTTP protocol and the other protocols, see Chapter 9.
In order to initially set up any Git server, you have to export an existing repository into a new bare repository — a repository that doesn’t contain a working directory. This is generally straightforward to do.
In order to clone your repository to create a new bare repository, you run the clone command with the
--bare option. By convention, bare repository directories end in
.git, like so:
$ git clone --bare my_project my_project.git Initialized empty Git repository in /opt/projects/my_project.git/
The output for this command is a little confusing. Since
clone is basically a
git init then a
git fetch, we see some output from the
git init part, which creates an empty directory. The actual object transfer gives no output, but it does happen. You should now have a copy of the Git directory data in your
This is roughly equivalent to something like
$ cp -Rf my_project/.git my_project.git
There are a couple of minor differences in the configuration file; but for your purpose, this is close to the same thing. It takes the Git repository by itself, without a working directory, and creates a directory specifically for it alone.
Now that you have a bare copy of your repository, all you need to do is put it on a server and set up your protocols. Let’s say you’ve set up a server called
git.example.com that you have SSH access to, and you want to store all your Git repositories under the
/opt/git directory. You can set up your new repository by copying your bare repository over:
$ scp -r my_project.git email@example.com:/opt/git
At this point, other users who have SSH access to the same server which has read-access to the
/opt/git directory can clone your repository by running
$ git clone firstname.lastname@example.org:/opt/git/my_project.git
If a user SSHs into a server and has write access to the
/opt/git/my_project.git directory, they will also automatically have push access. Git will automatically add group write permissions to a repository properly if you run the
git init command with the
$ ssh email@example.com $ cd /opt/git/my_project.git $ git init --bare --shared
You see how easy it is to take a Git repository, create a bare version, and place it on a server to which you and your collaborators have SSH access. Now you’re ready to collaborate on the same project.
It’s important to note that this is literally all you need to do to run a useful Git server to which several people have access — just add SSH-able accounts on a server, and stick a bare repository somewhere that all those users have read and write access to. You’re ready to go — nothing else needed.
In the next few sections, you’ll see how to expand to more sophisticated setups. This discussion will include not having to create user accounts for each user, adding public read access to repositories, setting up web UIs, using the Gitosis tool, and more. However, keep in mind that to collaborate with a couple of people on a private project, all you need is an SSH server and a bare repository.
If you’re a small outfit or are just trying out Git in your organization and have only a few developers, things can be simple for you. One of the most complicated aspects of setting up a Git server is user management. If you want some repositories to be read-only to certain users and read/write to others, access and permissions can be a bit difficult to arrange.
If you already have a server to which all your developers have SSH access, it’s generally easiest to set up your first repository there, because you have to do almost no work (as we covered in the last section). If you want more complex access control type permissions on your repositories, you can handle them with the normal filesystem permissions of the operating system your server runs.
If you want to place your repositories on a server that doesn’t have accounts for everyone on your team whom you want to have write access, then you must set up SSH access for them. We assume that if you have a server with which to do this, you already have an SSH server installed, and that’s how you’re accessing the server.
There are a few ways you can give access to everyone on your team. The first is to set up accounts for everybody, which is straightforward but can be cumbersome. You may not want to run
adduser and set temporary passwords for every user.
A second method is to create a single 'git' user on the machine, ask every user who is to have write access to send you an SSH public key, and add that key to the
~/.ssh/authorized_keys file of your new 'git' user. At that point, everyone will be able to access that machine via the 'git' user. This doesn’t affect the commit data in any way — the SSH user you connect as doesn’t affect the commits you’ve recorded.
Another way to do it is to have your SSH server authenticate from an LDAP server or some other centralized authentication source that you may already have set up. As long as each user can get shell access on the machine, any SSH authentication mechanism you can think of should work.
That being said, many Git servers authenticate using SSH public keys. In order to provide a public key, each user in your system must generate one if they don’t already have one. This process is similar across all operating systems.
First, you should check to make sure you don’t already have a key. By default, a user’s SSH keys are stored in that user’s
~/.ssh directory. You can easily check to see if you have a key already by going to that directory and listing the contents:
$ cd ~/.ssh $ ls authorized_keys2 id_dsa known_hosts config id_dsa.pub
You’re looking for a pair of files named something and something.pub, where the something is usually
.pub file is your public key, and the other file is your private key. If you don’t have these files (or you don’t even have a
.ssh directory), you can create them by running a program called
ssh-keygen, which is provided with the SSH package on Linux/Mac systems and comes with the MSysGit package on Windows:
$ ssh-keygen Generating public/private rsa key pair. Enter file in which to save the key (/Users/schacon/.ssh/id_rsa): Enter passphrase (empty for no passphrase): Enter same passphrase again: Your identification has been saved in /Users/schacon/.ssh/id_rsa. Your public key has been saved in /Users/schacon/.ssh/id_rsa.pub. The key fingerprint is: 43:c5:5b:5f:b1:f1:50:43:ad:20:a6:92:6a:1f:9a:3a firstname.lastname@example.org
First it confirms where you want to save the key (
.ssh/id_rsa), and then it asks twice for a passphrase, which you can leave empty if you don’t want to type a password when you use the key.
Now, each user that does this has to send their public key to you or whoever is administrating the Git server (assuming you’re using an SSH server setup that requires public keys). All they have to do is copy the contents of the
.pub file and e-mail it. The public keys look something like this:
$ cat ~/.ssh/id_rsa.pub ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAQEAklOUpkDHrfHY17SbrmTIpNLTGK9Tjom/BWDSU GPl+nafzlHDTYW7hdI4yZ5ew18JH4JW9jbhUFrviQzM7xlELEVf4h9lFX5QVkbPppSwg0cda3 Pbv7kOdJ/MTyBlWXFCR+HAo3FXRitBqxiX1nKhXpHAZsMciLq8V6RjsNAQwdsdMFvSlVK/7XA t3FaoJoAsncM1Q9x5+3V0Ww68/eIFmb1zuUFljQJKprrX88XypNDvjYNby6vw/Pb0rwert/En mZ+AW4OZPnTPI89ZPmVMLuayrD2cE86Z/il8b+gw3r3+1nKatmIkjn2so1d01QraTlMqVSsbx NrRFi9wrf+M7Q== email@example.com
For a more in-depth tutorial on creating an SSH key on multiple operating systems, see the GitHub guide on SSH keys at
Let’s walk through setting up SSH access on the server side. In this example, you’ll use the
authorized_keys method for authenticating your users. We also assume you’re running a standard Linux distribution like Ubuntu. First, you create a 'git' user and a
.ssh directory for that user.
$ sudo adduser git $ su git $ cd $ mkdir .ssh
Next, you need to add some developer SSH public keys to the
authorized_keys file for that user. Let’s assume you’ve received a few keys by e-mail and saved them to temporary files. Again, the public keys look something like this:
$ cat /tmp/id_rsa.john.pub ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCB007n/ww+ouN4gSLKssMxXnBOvf9LGt4L ojG6rs6hPB09j9R/T17/x4lhJA0F3FR1rP6kYBRsWj2aThGw6HXLm9/5zytK6Ztg3RPKK+4k Yjh6541NYsnEAZuXz0jTTyAUfrtU3Z5E003C4oxOj6H0rfIF1kKI9MAQLMdpGW1GYEIgS9Ez Sdfd8AcCIicTDWbqLAcU4UpkaX8KyGlLwsNuuGztobF8m72ALC/nLF6JLtPofwFBlgc+myiv O7TCUSBdLQlgMVOFq1I2uPWQOkOWQAHukEOmfjy2jctxSDBQ220ymjaNsHT4kgtZg2AYYgPq dAv8JggJICUvax2T9va5 gsg-keypair
You just append them to your
$ cat /tmp/id_rsa.john.pub >> ~/.ssh/authorized_keys $ cat /tmp/id_rsa.josie.pub >> ~/.ssh/authorized_keys $ cat /tmp/id_rsa.jessica.pub >> ~/.ssh/authorized_keys
Now, you can set up an empty repository for them by running
git init with the
--bare option, which initializes the repository without a working directory:
$ cd /opt/git $ mkdir project.git $ cd project.git $ git --bare init
Then, John, Josie, or Jessica can push the first version of their project into that repository by adding it as a remote and pushing up a branch. Note that someone must shell onto the machine and create a bare repository every time you want to add a project. Let’s use
gitserver as the hostname of the server on which you’ve set up your 'git' user and repository. If you’re running it internally, and you set up DNS for
gitserver to point to that server, then you can use the commands pretty much as is:
# on Johns computer $ cd myproject $ git init $ git add . $ git commit -m 'initial commit' $ git remote add origin git@gitserver:/opt/git/project.git $ git push origin master
At this point, the others can clone it down and push changes back up just as easily:
$ git clone git@gitserver:/opt/git/project.git $ vim README $ git commit -am 'fix for the README file' $ git push origin master
With this method, you can quickly get a read/write Git server up and running for a handful of developers.
As an extra precaution, you can easily restrict the 'git' user to only doing Git activities with a limited shell tool called
git-shell that comes with Git. If you set this as your 'git' user’s login shell, then the 'git' user can’t have normal shell access to your server. To use this, specify
git-shell instead of bash or csh for your user’s login shell. To do so, you’ll likely have to edit your
$ sudo vim /etc/passwd
At the bottom, you should find a line that looks something like this:
/usr/bin/git-shell (or run
which git-shell to see where it’s installed). The line should look something like this:
Now, the 'git' user can only use the SSH connection to push and pull Git repositories and can’t shell onto the machine. If you try, you’ll see a login rejection like this:
$ ssh git@gitserver fatal: What do you think I am? A shell? Connection to gitserver closed.
What if you want anonymous read access to your project? Perhaps instead of hosting an internal private project, you want to host an open source project. Or maybe you have a bunch of automated build servers or continuous integration servers that change a lot, and you don’t want to have to generate SSH keys all the time — you just want to add simple anonymous read access.
Probably the simplest way for smaller setups is to run a static web server with its document root where your Git repositories are, and then enable that
post-update hook we mentioned in the first section of this chapter. Let’s work from the previous example. Say you have your repositories in the
/opt/git directory, and an Apache server is running on your machine. Again, you can use any web server for this; but as an example, we’ll demonstrate some basic Apache configurations that should give you an idea of what you might need.
First you need to enable the hook:
$ cd project.git $ mv hooks/post-update.sample hooks/post-update $ chmod a+x hooks/post-update
If you’re using a version of Git earlier than 1.6, the
mv command isn’t necessary — Git started naming the hooks examples with the .sample postfix only recently.
What does this
post-update hook do? It looks basically like this:
$ cat .git/hooks/post-update #!/bin/sh exec git-update-server-info
This means that when you push to the server via SSH, Git will run this command to update the files needed for HTTP fetching.
Next, you need to add a VirtualHost entry to your Apache configuration with the document root as the root directory of your Git projects. Here, we’re assuming that you have wildcard DNS set up to send
*.gitserver to whatever box you’re using to run all this:
<VirtualHost *:80> ServerName git.gitserver DocumentRoot /opt/git <Directory /opt/git/> Order allow, deny allow from all </Directory> </VirtualHost>
You’ll also need to set the Unix user group of the
/opt/git directories to
www-data so your web server can read-access the repositories, because the Apache instance running the CGI script will (by default) be running as that user:
$ chgrp -R www-data /opt/git
When you restart Apache, you should be able to clone your repositories under that directory by specifying the URL for your project:
$ git clone http://git.gitserver/project.git
This way, you can set up HTTP-based read access to any of your projects for a fair number of users in a few minutes. Another simple option for public unauthenticated access is to start a Git daemon, although that requires you to daemonize the process - we’ll cover this option in the next section, if you prefer that route.
Now that you have basic read/write and read-only access to your project, you may want to set up a simple web-based visualizer. Git comes with a CGI script called GitWeb that is commonly used for this. You can see GitWeb in use at sites like
http://git.kernel.org (see Figure 4-1).
Insert 18333fig0401.png Figure 4-1. The GitWeb web-based user interface
If you want to check out what GitWeb would look like for your project, Git comes with a command to fire up a temporary instance if you have a lightweight server on your system like
webrick. On Linux machines,
lighttpd is often installed, so you may be able to get it to run by typing
git instaweb in your project directory. If you’re running a Mac, Leopard comes preinstalled with Ruby, so
webrick may be your best bet. To start
instaweb with a non-lighttpd handler, you can run it with the
$ git instaweb --httpd=webrick [2009-02-21 10:02:21] INFO WEBrick 1.3.1 [2009-02-21 10:02:21] INFO ruby 1.8.6 (2008-03-03) [universal-darwin9.0]
That starts up an HTTPD server on port 1234 and then automatically starts a web browser that opens on that page. It’s pretty easy on your part. When you’re done and want to shut down the server, you can run the same command with the
$ git instaweb --httpd=webrick --stop
If you want to run the web interface on a server all the time for your team or for an open source project you’re hosting, you’ll need to set up the CGI script to be served by your normal web server. Some Linux distributions have a
gitweb package that you may be able to install via
yum, so you may want to try that first. We’ll walk though installing GitWeb manually very quickly. First, you need to get the Git source code, which GitWeb comes with, and generate the custom CGI script:
$ git clone git://git.kernel.org/pub/scm/git/git.git $ cd git/ $ make GITWEB_PROJECTROOT="/opt/git" \ prefix=/usr gitweb/gitweb.cgi $ sudo cp -Rf gitweb /var/www/
Notice that you have to tell the command where to find your Git repositories with the
GITWEB_PROJECTROOT variable. Now, you need to make Apache use CGI for that script, for which you can add a VirtualHost:
<VirtualHost *:80> ServerName gitserver DocumentRoot /var/www/gitweb <Directory /var/www/gitweb> Options ExecCGI +FollowSymLinks +SymLinksIfOwnerMatch AllowOverride All order allow,deny Allow from all AddHandler cgi-script cgi DirectoryIndex gitweb.cgi </Directory> </VirtualHost>
Again, GitWeb can be served with any CGI capable web server; if you prefer to use something else, it shouldn’t be difficult to set up. At this point, you should be able to visit
http://gitserver/ to view your repositories online, and you can use
http://git.gitserver to clone and fetch your repositories over HTTP.
Keeping all users’ public keys in the
authorized_keys file for access works well only for a while. When you have hundreds of users, it’s much more of a pain to manage that process. You have to shell onto the server each time, and there is no access control — everyone in the file has read and write access to every project.
At this point, you may want to turn to a widely used software project called Gitosis. Gitosis is basically a set of scripts that help you manage the
authorized_keys file as well as implement some simple access controls. The really interesting part is that the UI for this tool for adding people and determining access isn’t a web interface but a special Git repository. You set up the information in that project; and when you push it, Gitosis reconfigures the server based on that, which is cool.
Installing Gitosis isn’t the simplest task ever, but it’s not too difficult. It’s easiest to use a Linux server for it — these examples use a stock Ubuntu 8.10 server.
Gitosis requires some Python tools, so first you have to install the Python setuptools package, which Ubuntu provides as python-setuptools:
$ apt-get install python-setuptools
Next, you clone and install Gitosis from the project’s main site:
$ git clone git://eagain.net/gitosis.git $ cd gitosis $ sudo python setup.py install
That installs a couple of executables that Gitosis will use. Next, Gitosis wants to put its repositories under
/home/git, which is fine. But you have already set up your repositories in
/opt/git, so instead of reconfiguring everything, you create a symlink:
$ ln -s /opt/git /home/git/repositories
Gitosis is going to manage your keys for you, so you need to remove the current file, re-add the keys later, and let Gitosis control the
authorized_keys file automatically. For now, move the
authorized_keys file out of the way:
$ mv /home/git/.ssh/authorized_keys /home/git/.ssh/ak.bak
Next you need to turn your shell back on for the 'git' user, if you changed it to the
git-shell command. People still won’t be able to log in, but Gitosis will control that for you. So, let’s change this line in your
back to this:
Now it’s time to initialize Gitosis. You do this by running the
gitosis-init command with your personal public key. If your public key isn’t on the server, you’ll have to copy it there:
$ sudo -H -u git gitosis-init < /tmp/id_dsa.pub Initialized empty Git repository in /opt/git/gitosis-admin.git/ Reinitialized existing Git repository in /opt/git/gitosis-admin.git/
This lets the user with that key modify the main Git repository that controls the Gitosis setup. Next, you have to manually set the execute bit on the
post-update script for your new control repository.
$ sudo chmod 755 /opt/git/gitosis-admin.git/hooks/post-update
You’re ready to roll. If you’re set up correctly, you can try to SSH into your server as the user for which you added the public key to initialize Gitosis. You should see something like this:
$ ssh git@gitserver PTY allocation request failed on channel 0 fatal: unrecognized command 'gitosis-serve schacon@quaternion' Connection to gitserver closed.
That means Gitosis recognized you but shut you out because you’re not trying to do any Git commands. So, let’s do an actual Git command — you’ll clone the Gitosis control repository:
# on your local computer $ git clone git@gitserver:gitosis-admin.git
Now you have a directory named
gitosis-admin, which has two major parts:
$ cd gitosis-admin $ find . ./gitosis.conf ./keydir ./keydir/scott.pub
gitosis.conf file is the control file you use to specify users, repositories, and permissions. The
keydir directory is where you store the public keys of all the users who have any sort of access to your repositories — one file per user. The name of the file in
keydir (in the previous example,
scott.pub) will be different for you — Gitosis takes that name from the description at the end of the public key that was imported with the
If you look at the
gitosis.conf file, it should only specify information about the
gitosis-admin project that you just cloned:
$ cat gitosis.conf [gitosis] [group gitosis-admin] writable = gitosis-admin members = scott
It shows you that the 'scott' user — the user with whose public key you initialized Gitosis — is the only one who has access to the
Now, let’s add a new project for you. You’ll add a new section called
mobile where you’ll list the developers on your mobile team and projects that those developers need access to. Because 'scott' is the only user in the system right now, you’ll add him as the only member, and you’ll create a new project called
iphone_project to start on:
[group mobile] writable = iphone_project members = scott
Whenever you make changes to the
gitosis-admin project, you have to commit the changes and push them back up to the server in order for them to take effect:
$ git commit -am 'add iphone_project and mobile group' [master]: created 8962da8: "changed name" 1 files changed, 4 insertions(+), 0 deletions(-) $ git push Counting objects: 5, done. Compressing objects: 100% (2/2), done. Writing objects: 100% (3/3), 272 bytes, done. Total 3 (delta 1), reused 0 (delta 0) To git@gitserver:/opt/git/gitosis-admin.git fb27aec..8962da8 master -> master
You can make your first push to the new
iphone_project project by adding your server as a remote to your local version of the project and pushing. You no longer have to manually create a bare repository for new projects on the server — Gitosis creates them automatically when it sees the first push:
$ git remote add origin git@gitserver:iphone_project.git $ git push origin master Initialized empty Git repository in /opt/git/iphone_project.git/ Counting objects: 3, done. Writing objects: 100% (3/3), 230 bytes, done. Total 3 (delta 0), reused 0 (delta 0) To git@gitserver:iphone_project.git * [new branch] master -> master
Notice that you don’t need to specify the path (in fact, doing so won’t work), just a colon and then the name of the project — Gitosis finds it for you.
You want to work on this project with your friends, so you’ll have to re-add their public keys. But instead of appending them manually to the
~/.ssh/authorized_keys file on your server, you’ll add them, one key per file, into the
keydir directory. How you name the keys determines how you refer to the users in the
gitosis.conf file. Let’s re-add the public keys for John, Josie, and Jessica:
$ cp /tmp/id_rsa.john.pub keydir/john.pub $ cp /tmp/id_rsa.josie.pub keydir/josie.pub $ cp /tmp/id_rsa.jessica.pub keydir/jessica.pub
Now you can add them all to your 'mobile' team so they have read and write access to
[group mobile] writable = iphone_project members = scott john josie jessica
After you commit and push that change, all four users will be able to read from and write to that project.
Gitosis has simple access controls as well. If you want John to have only read access to this project, you can do this instead:
[group mobile] writable = iphone_project members = scott josie jessica [group mobile_ro] readonly = iphone_project members = john
Now John can clone the project and get updates, but Gitosis won’t allow him to push back up to the project. You can create as many of these groups as you want, each containing different users and projects. You can also specify another group as one of the members, to inherit all of its members automatically.
If you have any issues, it may be useful to add
loglevel=DEBUG under the
[gitosis] section. If you’ve lost push access by pushing a messed-up configuration, you can manually fix the file on the server under
/home/git/.gitosis.conf — the file from which Gitosis reads its info. A push to the project takes the
gitosis.conf file you just pushed up and sticks it there. If you edit that file manually, it remains like that until the next successful push to the
For public, unauthenticated read access to your projects, you’ll want to move past the HTTP protocol and start using the Git protocol. The main reason is speed. The Git protocol is far more efficient and thus faster than the HTTP protocol, so using it will save your users time.
Again, this is for unauthenticated read-only access. If you’re running this on a server outside your firewall, it should only be used for projects that are publicly visible to the world. If the server you’re running it on is inside your firewall, you might use it for projects that a large number of people or computers (continuous integration or build servers) have read-only access to, when you don’t want to have to add an SSH key for each.
In any case, the Git protocol is relatively easy to set up. Basically, you need to run this command in a daemonized manner:
git daemon --reuseaddr --base-path=/opt/git/ /opt/git/
--reuseaddr allows the server to restart without waiting for old connections to time out, the
--base-path option allows people to clone projects without specifying the entire path, and the path at the end tells the Git daemon where to look for repositories to export. If you’re running a firewall, you’ll also need to punch a hole in it at port 9418 on the box you’re setting this up on.
You can daemonize this process a number of ways, depending on the operating system you’re running. On an Ubuntu machine, you use an Upstart script. So, in the following file
you put this script:
start on startup stop on shutdown exec /usr/bin/git daemon \ --user=git --group=git \ --reuseaddr \ --base-path=/opt/git/ \ /opt/git/ respawn
For security reasons, it is strongly encouraged to have this daemon run as a user with read-only permissions to the repositories – you can easily do this by creating a new user 'git-ro' and running the daemon as them. For the sake of simplicity we’ll simply run it as the same 'git' user that Gitosis is running as.
When you restart your machine, your Git daemon will start automatically and respawn if it goes down. To get it running without having to reboot, you can run this:
initctl start local-git-daemon
On other systems, you may want to use
xinetd, a script in your
sysvinit system, or something else — as long as you get that command daemonized and watched somehow.
Next, you have to tell your Gitosis server which repositories to allow unauthenticated Git server-based access to. If you add a section for each repository, you can specify the ones from which you want your Git daemon to allow reading. If you want to allow Git protocol access for your iphone project, you add this to the end of the
[repo iphone_project] daemon = yes
When that is committed and pushed up, your running daemon should start serving requests for the project to anyone who has access to port 9418 on your server.
If you decide not to use Gitosis, but you want to set up a Git daemon, you’ll have to run this on each project you want the Git daemon to serve:
$ cd /path/to/project.git $ touch git-daemon-export-ok
The presence of that file tells Git that it’s OK to serve this project without authentication.
Gitosis can also control which projects GitWeb shows. First, you need to add something like the following to the
$projects_list = "/home/git/gitosis/projects.list"; $projectroot = "/home/git/repositories"; $export_ok = "git-daemon-export-ok"; @git_base_url_list = ('git://gitserver');
You can control which projects GitWeb lets users browse by adding or removing a
gitweb setting in the Gitosis configuration file. For instance, if you want the iphone project to show up on GitWeb, you make the
repo setting look like this:
[repo iphone_project] daemon = yes gitweb = yes
Now, if you commit and push the project, GitWeb will automatically start showing your iphone project.
If you don’t want to go through all of the work involved in setting up your own Git server, you have several options for hosting your Git projects on an external dedicated hosting site. Doing so offers a number of advantages: a hosting site is generally quick to set up and easy to start projects on, and no server maintenance or monitoring is involved. Even if you set up and run your own server internally, you may still want to use a public hosting site for your open source code — it’s generally easier for the open source community to find and help you with.
These days, you have a huge number of hosting options to choose from, each with different advantages and disadvantages. To see an up-to-date list, check out the GitHosting page on the main Git wiki:
Because we can’t cover all of them, and because I happen to work at one of them, we’ll use this section to walk through setting up an account and creating a new project at GitHub. This will give you an idea of what is involved.
GitHub is by far the largest open source Git hosting site and it’s also one of the very few that offers both public and private hosting options so you can keep your open source and private commercial code in the same place. In fact, we used GitHub to privately collaborate on this book.
GitHub is slightly different than most code-hosting sites in the way that it namespaces projects. Instead of being primarily based on the project, GitHub is user centric. That means when I host my
grit project on GitHub, you won’t find it at
github.com/grit but instead at
github.com/schacon/grit. There is no canonical version of any project, which allows a project to move from one user to another seamlessly if the first author abandons the project.
GitHub is also a commercial company that charges for accounts that maintain private repositories, but anyone can quickly get a free account to host as many open source projects as they want. We’ll quickly go over how that is done.
The first thing you need to do is set up a free user account. If you visit the Pricing and Signup page at
http://github.com/plans and click the "Sign Up" button on the Free account (see figure 4-2), you’re taken to the signup page.
Insert 18333fig0402.png Figure 4-2. The GitHub plan page
Here you must choose a username that isn’t yet taken in the system and enter an e-mail address that will be associated with the account and a password (see Figure 4-3).
Insert 18333fig0403.png Figure 4-3. The GitHub user signup form
If you have it available, this is a good time to add your public SSH key as well. We covered how to generate a new key earlier, in the "Simple Setups" section. Take the contents of the public key of that pair, and paste it into the SSH Public Key text box. Clicking the "explain ssh keys" link takes you to detailed instructions on how to do so on all major operating systems. Clicking the "I agree, sign me up" button takes you to your new user dashboard (see Figure 4-4).
Insert 18333fig0404.png Figure 4-4. The GitHub user dashboard
Next you can create a new repository.
Start by clicking the "create a new one" link next to Your Repositories on the user dashboard. You’re taken to the Create a New Repository form (see Figure 4-5).
Insert 18333fig0405.png Figure 4-5. Creating a new repository on GitHub
All you really have to do is provide a project name, but you can also add a description. When that is done, click the "Create Repository" button. Now you have a new repository on GitHub (see Figure 4-6).
Insert 18333fig0406.png Figure 4-6. GitHub project header information
Since you have no code there yet, GitHub will show you instructions for how create a brand-new project, push an existing Git project up, or import a project from a public Subversion repository (see Figure 4-7).
Insert 18333fig0407.png Figure 4-7. Instructions for a new repository
These instructions are similar to what we’ve already gone over. To initialize a project if it isn’t already a Git project, you use
$ git init $ git add . $ git commit -m 'initial commit'
When you have a Git repository locally, add GitHub as a remote and push up your master branch:
$ git remote add origin firstname.lastname@example.org:testinguser/iphone_project.git $ git push origin master
Now your project is hosted on GitHub, and you can give the URL to anyone you want to share your project with. In this case, it’s
http://github.com/testinguser/iphone_project. You can also see from the header on each of your project’s pages that you have two Git URLs (see Figure 4-8).
Insert 18333fig0408.png Figure 4-8. Project header with a public URL and a private URL
The Public Clone URL is a public, read-only Git URL over which anyone can clone the project. Feel free to give out that URL and post it on your web site or what have you.
The Your Clone URL is a read/write SSH-based URL that you can read or write over only if you connect with the SSH private key associated with the public key you uploaded for your user. When other users visit this project page, they won’t see that URL—only the public one.
If you have an existing public Subversion project that you want to import into Git, GitHub can often do that for you. At the bottom of the instructions page is a link to a Subversion import. If you click it, you see a form with information about the import process and a text box where you can paste in the URL of your public Subversion project (see Figure 4-9).
Insert 18333fig0409.png Figure 4-9. Subversion importing interface
If your project is very large, nonstandard, or private, this process probably won’t work for you. In Chapter 7, you’ll learn how to do more complicated manual project imports.
Let’s add the rest of the team. If John, Josie, and Jessica all sign up for accounts on GitHub, and you want to give them push access to your repository, you can add them to your project as collaborators. Doing so will allow pushes from their public keys to work.
Click the "edit" button in the project header or the Admin tab at the top of the project to reach the Admin page of your GitHub project (see Figure 4-10).
Insert 18333fig0410.png Figure 4-10. GitHub administration page
To give another user write access to your project, click the “Add another collaborator” link. A new text box appears, into which you can type a username. As you type, a helper pops up, showing you possible username matches. When you find the correct user, click the Add button to add that user as a collaborator on your project (see Figure 4-11).
Insert 18333fig0411.png Figure 4-11. Adding a collaborator to your project
When you’re finished adding collaborators, you should see a list of them in the Repository Collaborators box (see Figure 4-12).
Insert 18333fig0412.png Figure 4-12. A list of collaborators on your project
If you need to revoke access to individuals, you can click the "revoke" link, and their push access will be removed. For future projects, you can also copy collaborator groups by copying the permissions of an existing project.
After you push your project up or have it imported from Subversion, you have a main project page that looks something like Figure 4-13.
Insert 18333fig0413.png Figure 4-13. A GitHub main project page
When people visit your project, they see this page. It contains tabs to different aspects of your projects. The Commits tab shows a list of commits in reverse chronological order, similar to the output of the
git log command. The Network tab shows all the people who have forked your project and contributed back. The Downloads tab allows you to upload project binaries and link to tarballs and zipped versions of any tagged points in your project. The Wiki tab provides a wiki where you can write documentation or other information about your project. The Graphs tab has some contribution visualizations and statistics about your project. The main Source tab that you land on shows your project’s main directory listing and automatically renders the README file below it if you have one. This tab also shows a box with the latest commit information.
If you want to contribute to an existing project to which you don’t have push access, GitHub encourages forking the project. When you land on a project page that looks interesting and you want to hack on it a bit, you can click the "fork" button in the project header to have GitHub copy that project to your user so you can push to it.
This way, projects don’t have to worry about adding users as collaborators to give them push access. People can fork a project and push to it, and the main project maintainer can pull in those changes by adding them as remotes and merging in their work.
To fork a project, visit the project page (in this case, mojombo/chronic) and click the "fork" button in the header (see Figure 4-14).
Insert 18333fig0414.png Figure 4-14. Get a writable copy of any repository by clicking the "fork" button.
After a few seconds, you’re taken to your new project page, which indicates that this project is a fork of another one (see Figure 4-15).
Insert 18333fig0415.png Figure 4-15. Your fork of a project
That’s all we’ll cover about GitHub, but it’s important to note how quickly you can do all this. You can create an account, add a new project, and push to it in a matter of minutes. If your project is open source, you also get a huge community of developers who now have visibility into your project and may well fork it and help contribute to it. At the very least, this may be a way to get up and running with Git and try it out quickly.
You have several options to get a remote Git repository up and running so that you can collaborate with others or share your work.
Running your own server gives you a lot of control and allows you to run the server within your own firewall, but such a server generally requires a fair amount of your time to set up and maintain. If you place your data on a hosted server, it’s easy to set up and maintain; however, you have to be able to keep your code on someone else’s servers, and some organizations don’t allow that.
It should be fairly straightforward to determine which solution or combination of solutions is appropriate for you and your organization.