From b567049362ac3ec5c1aca5ecf48714c80c232505 Mon Sep 17 00:00:00 2001
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
Date: Wed, 11 Mar 2020 12:14:58 +0000
Subject: [PATCH] Revert "media: dt-bindings: Add binding for the Sony IMX219
 sensor"

This reverts commit e3dca865875b345a2fa45e8295e32d701c666334.
---
 .../devicetree/bindings/media/i2c/imx219.txt  | 59 -------------------
 1 file changed, 59 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.txt

diff --git a/Documentation/devicetree/bindings/media/i2c/imx219.txt b/Documentation/devicetree/bindings/media/i2c/imx219.txt
deleted file mode 100644
index a02f1ce1e1204..0000000000000
--- a/Documentation/devicetree/bindings/media/i2c/imx219.txt
+++ /dev/null
@@ -1,59 +0,0 @@
-* Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
-
-The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor with
-an active array size of 3280H x 2464V. It is programmable through I2C
-interface. The I2C address is fixed to 0x10 as per sensor data sheet.
-Image data is sent through MIPI CSI-2, which is configured as either 2 or 4
-data lanes.
-
-Required Properties:
-- compatible: value should be "sony,imx219" for imx219 sensor
-- reg: I2C bus address of the device
-- clocks: reference to the xclk input clock.
-- clock-names: should be "xclk".
-- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
-- AVDD-supply: Analog voltage supply, 2.8 volts
-- DVDD-supply: Digital core voltage supply, 1.2 volts
-
-Optional Properties:
-- xclr-gpios: reference to the GPIO connected to the xclr pin, if any. Must be
-	      released after all supplies are applied.
-	      This is an active high signal to the imx219.
-
-The imx219 device node should contain one 'port' child node with
-an 'endpoint' subnode. For further reading on port node refer to
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Endpoint node required properties for CSI-2 connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
-- data-lanes: should be set to <1 2>, or  <1 2 3 4> (two or four lane CSI-2
-  supported)
-
-Example:
-	sensor@10 {
-		compatible = "sony,imx219";
-		reg = <0x10>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&imx219_clk>;
-		clock-names = "xclk";
-		xclr-gpios = <&gpio_sensor 0 0>;
-		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
-		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
-		DVDD-supply = <&vgen2_reg>;  /* 1.2v */
-
-		imx219_clk: camera-clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <24000000>;
-		};
-
-		port {
-			sensor_out: endpoint {
-				remote-endpoint = <&csiss_in>;
-				clock-lanes = <0>;
-				data-lanes = <1 2>;
-			};
-		};
-	};