Skip to content
This repository
Closed
wants to merge 3 commits into from

3 participants

Stephen Warren Chris Boot popcornmix
Stephen Warren
swarren commented May 21, 2012

This is a driver for the BCM2708's HW I2C controller

added some commits May 21, 2012
Stephen Warren i2c: bcm2708: initial driver
I2C driver for the BCM2708 series, as used on the Raspberry Pi.

This driver supports 7-bit addressing, but not 10-bit. The HW supports
10-bit.

This driver does not support repeated starts. It's not clear from the
data sheet how to create repeated starts.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
9fd4298
Stephen Warren HACK: ARM: bcm2708: mux I2C0 onto GPIO0/1
Set up the GPIO/pinmux so that I2C0 is mux'd onto GPIOs 0/1, so that
the controller can actually communicate with the outside world.

Ideally, this would be set up using pinctrl, but that doesn't exist
in this old kernel.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
a61933c
Stephen Warren ARM: bcm2708: instantiate I2C0 device
The BCM2708 has 3 I2C adapters. This change instantiates the first of
these, which is attached to the expansion header on the Raspberry Pi.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
dbf3ef5
Chris Boot
bootc commented May 22, 2012

Hah, I knew this would happen :-( I also have an I2C driver in https://github.com/bootc/linux/tree/rpi-i2cspi

Stephen Warren
swarren commented May 22, 2012

Hmm. I like some things better from each driver. I can update my version to incorporate the good parts from your branch, and either issue a new pull request or replace this one, depending on whether I get done before this gets pulled in or not.

BTW, is anyone planning on pushing bcm2708 core support into the mainline kernel? I was tempted to start working on that myself unless someone is already doing it.

Chris Boot
bootc commented May 23, 2012

As I already 'publish' my kernel (http://www.bootc.net/) I'd really appreciate it if you could either comment on what you'd like to see different in my code or send over patches / pull requests. I'd be perfectly happy for our drivers to end up looking identical with bits from yours and bits from mine.

And as for the second question - yes, there is an effort to get the arch/mach code into mainline. Simon Arlott is currently leading this effort (lp0 here on GitHub) and there's a small group of us working on it. Sadly we mostly had to wipe the slate clean and start again for this as there are requirements to use device tree, etc...

You may want to take a look at https://github.com/lp0/linux/tree/rpi-linear

I should mention I'm currently working on forward-porting my SPI driver into that branch, doing the device tree conversion as well as updating it for queued submission as required by the new SPI core.

HTH,
Chris

Stephen Warren
swarren commented May 23, 2012

Sure, I'll take a look at that.

popcornmix
Owner

Thanks swarren, but I'll close this pull request, as lp0/bootc are working on what I hope will be the upstreamable kernel we use in the future. Please send any pull requests to bootc.

If there's demand for bootc's I2C/SPI drivers to be merged into this kernel in the interim, then that's a option.

popcornmix popcornmix closed this May 26, 2012
Chris Boot
bootc commented May 26, 2012

Let me know if you want the SPI/I2C drivers and I can get them cleaned up and tested against the 3.1.9 kernel.

popcornmix
Owner

Yes, that would be great.

Ben Arblaster andatche referenced this pull request from a commit in andatche/raspi-linux December 16, 2011
usbfs: Fix oops related to user namespace conversion.
commit 1b41c83 upstream.

When running the Point Grey "flycap" program for their USB 3.0 camera
(which was running as a USB 2.0 device for some reason), I trigger this
oops whenever I try to open a video stream:

Dec 15 16:48:34 puck kernel: [ 1798.715559] BUG: unable to handle kernel NULL pointer dereference at           (null)
Dec 15 16:48:34 puck kernel: [ 1798.719153] IP: [<ffffffff8147841e>] free_async+0x1e/0x70
Dec 15 16:48:34 puck kernel: [ 1798.720991] PGD 6f833067 PUD 6fc56067 PMD 0
Dec 15 16:48:34 puck kernel: [ 1798.722815] Oops: 0002 [#1] SMP
Dec 15 16:48:34 puck kernel: [ 1798.724627] CPU 0
Dec 15 16:48:34 puck kernel: [ 1798.724636] Modules linked in: ecryptfs encrypted_keys sha1_generic trusted binfmt_misc sha256_generic aesni_intel cryptd aes_x86_64 aes_generic parport_pc dm_crypt ppdev joydev snd_hda_codec_hdmi snd_hda_codec_conexant arc4 iwlwifi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm thinkpad_acpi mac80211 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer btusb uvcvideo snd_seq_device bluetooth videodev psmouse snd v4l2_compat_ioctl32 serio_raw tpm_tis cfg80211 tpm tpm_bios nvram soundcore snd_page_alloc lp parport i915 xhci_hcd ahci libahci drm_kms_helper drm sdhci_pci sdhci e1000e i2c_algo_bit video
Dec 15 16:48:34 puck kernel: [ 1798.734212]
Dec 15 16:48:34 puck kernel: [ 1798.736162] Pid: 2713, comm: FlyCap2 Not tainted 3.2.0-rc5+ #28 LENOVO 4286CTO/4286CTO
Dec 15 16:48:34 puck kernel: [ 1798.738148] RIP: 0010:[<ffffffff8147841e>]  [<ffffffff8147841e>] free_async+0x1e/0x70
Dec 15 16:48:34 puck kernel: [ 1798.740134] RSP: 0018:ffff88005715fd78  EFLAGS: 00010296
Dec 15 16:48:34 puck kernel: [ 1798.742118] RAX: 00000000fffffff4 RBX: ffff88006fe8f900 RCX: 0000000000004118
Dec 15 16:48:34 puck kernel: [ 1798.744116] RDX: 0000000001000000 RSI: 0000000000016390 RDI: 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.746087] RBP: ffff88005715fd88 R08: 0000000000000000 R09: ffffffff8146f22e
Dec 15 16:48:34 puck kernel: [ 1798.748018] R10: ffff88006e520ac0 R11: 0000000000000001 R12: ffff88005715fe28
Dec 15 16:48:34 puck kernel: [ 1798.749916] R13: ffff88005d31df00 R14: ffff88006fe8f900 R15: 00007f688c995cb8
Dec 15 16:48:34 puck kernel: [ 1798.751785] FS:  00007f68a366da40(0000) GS:ffff880100200000(0000) knlGS:0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.753659] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Dec 15 16:48:34 puck kernel: [ 1798.755509] CR2: 0000000000000000 CR3: 00000000706bb000 CR4: 00000000000406f0
Dec 15 16:48:34 puck kernel: [ 1798.757334] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.759124] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Dec 15 16:48:34 puck kernel: [ 1798.760871] Process FlyCap2 (pid: 2713, threadinfo ffff88005715e000, task ffff88006c675b80)
Dec 15 16:48:34 puck kernel: [ 1798.762605] Stack:
Dec 15 16:48:34 puck kernel: [ 1798.764297]  ffff88005715fe28 0000000000000000 ffff88005715fe08 ffffffff81479058
Dec 15 16:48:34 puck kernel: [ 1798.766020]  0000000000000000 ffffea0000004000 ffff880000004118 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.767750]  ffff880000000001 ffff88006e520ac0 fffffff46fd81180 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.769472] Call Trace:
Dec 15 16:48:34 puck kernel: [ 1798.771147]  [<ffffffff81479058>] proc_do_submiturb+0x778/0xa00
Dec 15 16:48:34 puck kernel: [ 1798.772798]  [<ffffffff8147a5fd>] usbdev_do_ioctl+0x24d/0x1200
Dec 15 16:48:34 puck kernel: [ 1798.774410]  [<ffffffff8147b5de>] usbdev_ioctl+0xe/0x20
Dec 15 16:48:34 puck kernel: [ 1798.775975]  [<ffffffff81189259>] do_vfs_ioctl+0x99/0x600
Dec 15 16:48:34 puck kernel: [ 1798.777534]  [<ffffffff81189851>] sys_ioctl+0x91/0xa0
Dec 15 16:48:34 puck kernel: [ 1798.779088]  [<ffffffff816247c2>] system_call_fastpath+0x16/0x1b
ec 15 16:48:34 puck kernel: [ 1798.780634] Code: 51 ff ff ff e9 29 ff ff ff 0f 1f 40 00 55 48 89 e5 53 48 83 ec 08 66 66 66 66 90 48 89 fb 48 8b 7f 18 e8 a6 ea c0 ff 4
8 8b 7b 20 <f0> ff 0f 0f 94 c0 84 c0 74 05 e8 d3 99 c1 ff 48 8b 43 40 48 8b
Dec 15 16:48:34 puck kernel: [ 1798.783970] RIP  [<ffffffff8147841e>] free_async+0x1e/0x70
Dec 15 16:48:34 puck kernel: [ 1798.785630]  RSP <ffff88005715fd78>
Dec 15 16:48:34 puck kernel: [ 1798.787274] CR2: 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.794728] ---[ end trace 52894d3355f88d19 ]---

markup_oops.pl says the oops is in put_cred:

 ffffffff81478401:      48 89 e5                mov    %rsp,%rbp
 ffffffff81478404:      53                      push   %rbx
 ffffffff81478405:      48 83 ec 08             sub    $0x8,%rsp
 ffffffff81478409:      e8 f2 c0 1a 00          callq  ffffffff81624500 <mcount>
 ffffffff8147840e:      48 89 fb                mov    %rdi,%rbx   |  %ebx => ffff88006fe8f900
        put_pid(as->pid);
 ffffffff81478411:      48 8b 7f 18             mov    0x18(%rdi),%rdi
 ffffffff81478415:      e8 a6 ea c0 ff          callq  ffffffff81086ec0 <put_pid>
        put_cred(as->cred);
 ffffffff8147841a:      48 8b 7b 20             mov    0x20(%rbx),%rdi |  %edi => 0  %ebx = ffff88006fe8f900
  */
 static inline int atomic_dec_and_test(atomic_t *v)
 {
        unsigned char c;

        asm volatile(LOCK_PREFIX "decl %0; sete %1"
*ffffffff8147841e:      f0 ff 0f                lock decl (%rdi)   |  %edi = 0 <--- faulting instruction
 ffffffff81478421:      0f 94 c0                sete   %al
 static inline void put_cred(const struct cred *_cred)
 {
        struct cred *cred = (struct cred *) _cred;

        validate_creds(cred);
        if (atomic_dec_and_test(&(cred)->usage))
 ffffffff81478424:      84 c0                   test   %al,%al
 ffffffff81478426:      74 05                   je     ffffffff8147842d <free_async+0x2d>
                __put_cred(cred);
 ffffffff81478428:      e8 d3 99 c1 ff          callq  ffffffff81091e00 <__put_cred>
        kfree(as->urb->transfer_buffer);
 ffffffff8147842d:      48 8b 43 40             mov    0x40(%rbx),%rax
 ffffffff81478431:      48 8b 78 68             mov    0x68(%rax),%rdi
 ffffffff81478435:      e8 a6 e1 ce ff          callq  ffffffff811665e0 <kfree>
        kfree(as->urb->setup_packet);
 ffffffff8147843a:      48 8b 43 40             mov    0x40(%rbx),%rax
 ffffffff8147843e:      48 8b b8 90 00 00 00    mov    0x90(%rax),%rdi
 ffffffff81478445:      e8 96 e1 ce ff          callq  ffffffff811665e0 <kfree>
        usb_free_urb(as->urb);
 ffffffff8147844a:      48 8b 7b 40             mov    0x40(%rbx),%rdi
 ffffffff8147844e:      e8 0d 6b ff ff          callq  ffffffff8146ef60 <usb_free_urb>

This bug seems to have been introduced by commit
d178bc3a708f39cbfefc3fab37032d3f2511b4ec "user namespace: usb: make usb
urbs user namespace aware (v2)"

I'm not sure if this is right fix, but it does stop the oops.

Unfortunately, the Point Grey software still refuses to work, but it's a
closed source app, so I can't fix it.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
7f35a69
Ben Arblaster andatche referenced this pull request from a commit in andatche/raspi-linux April 12, 2012
Marek Belisko staging: iio: hmc5843: Fix crash in probe function.
commit 62d2feb upstream.

Fix crash after issuing:
	echo hmc5843 0x1e > /sys/class/i2c-dev/i2c-2/device/new_device

	[   37.180999] device: '2-001e': device_add
	[   37.188293] bus: 'i2c': add device 2-001e
	[   37.194549] PM: Adding info for i2c:2-001e
	[   37.200958] bus: 'i2c': driver_probe_device: matched device 2-001e with driver hmc5843
	[   37.210815] bus: 'i2c': really_probe: probing driver hmc5843 with device 2-001e
	[   37.224884] HMC5843 initialized
	[   37.228759] ------------[ cut here ]------------
	[   37.233612] kernel BUG at mm/slab.c:505!
	[   37.237701] Internal error: Oops - BUG: 0 [#1] PREEMPT
	[   37.243103] Modules linked in:
	[   37.246337] CPU: 0    Not tainted  (3.3.1-gta04+ #28)
	[   37.251647] PC is at kfree+0x84/0x144
	[   37.255493] LR is at kfree+0x20/0x144
	[   37.259338] pc : [<c00b408c>]    lr : [<c00b4028>]    psr: 40000093
	[   37.259368] sp : de249cd8  ip : 0000000c  fp : 00000090
	[   37.271362] r10: 0000000a  r9 : de229eac  r8 : c0236274
	[   37.276855] r7 : c09d6490  r6 : a0000013  r5 : de229c00  r4 : de229c10
	[   37.283691] r3 : c0f00218  r2 : 00000400  r1 : c0eea000  r0 : c00b4028
	[   37.290527] Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
	[   37.298095] Control: 10c5387d  Table: 9e1d0019  DAC: 00000015
	[   37.304107] Process sh (pid: 91, stack limit = 0xde2482f0)
	[   37.309844] Stack: (0xde249cd8 to 0xde24a000)
	[   37.314422] 9cc0:                                                       de229c10 de229c00
	[   37.322998] 9ce0: de229c10 ffffffea 00000005 c0236274 de140a80 c00b4798 dec00080 de140a80
	[   37.331573] 9d00: c032f37c dec00080 000080d0 00000001 de229c00 de229c10 c048d578 00000005
	[   37.340148] 9d20: de229eac 0000000a 00000090 c032fa40 00000001 00000000 00000001 de229c10
	[   37.348724] 9d40: de229eac 00000029 c075b558 00000001 00000003 00000004 de229c10 c048d594
	[   37.357299] 9d60: 00000000 60000013 00000018 205b0007 37332020 3432322e 5d343838 c0060020
	[   37.365905] 9d80: de251600 00000001 00000000 de251600 00000001 c0065a84 de229c00 de229c48
	[   37.374481] 9da0: 00000006 0048d62c de229c38 de229c00 de229c00 de1f6c00 de1f6c20 00000001
	[   37.383056] 9dc0: 00000000 c048d62c 00000000 de229c00 de229c00 de1f6c00 de1f6c20 00000001
	[   37.391632] 9de0: 00000000 c048d62c 00000000 c0330164 00000000 de1f6c20 c048d62c de1f6c00
	[   37.400207] 9e00: c0330078 de1f6c04 c078d714 de189b58 00000000 c02ccfd8 de1f6c20 c0795f40
	[   37.408782] 9e20: c0238330 00000000 00000000 c02381a8 de1b9fc0 de1f6c20 de1f6c20 de249e48
	[   37.417358] 9e40: c0238330 c0236bb0 decdbed8 de7d0f14 de1f6c20 de1f6c20 de1f6c54 de1f6c20
	[   37.425933] 9e60: 00000000 c0238030 de1f6c20 c078d7bc de1f6c20 c02377ec de1f6c20 de1f6c28
	[   37.434509] 9e80: dee64cb0 c0236138 c047c554 de189b58 00000000 c004b45c de1f6c20 de1f6cd8
	[   37.443084] 9ea0: c0edfa6c de1f6c00 dee64c68 de1f6c04 de1f6c20 dee64cb8 c047c554 de189b58
	[   37.451690] 9ec0: 00000000 c02cd634 dee64c68 de249ef4 de23b008 dee64cb0 0000000d de23b000
	[   37.460266] 9ee0: de23b007 c02cd78c 00000002 00000000 00000000 35636d68 00333438 00000000
	[   37.468841] 9f00: 00000000 00000000 001e0000 00000000 00000000 00000000 00000000 0a10cec0
	[   37.477416] 9f20: 00000002 de249f80 0000000d dee62990 de189b40 c0234d88 0000000d c010c354
	[   37.485992] 9f40: 0000000d de210f28 000acc88 de249f80 0000000d de248000 00000000 c00b7bf8
	[   37.494567] 9f60: de210f28 000acc88 de210f28 000acc88 00000000 00000000 0000000d c00b7ed8
	[   37.503143] 9f80: 00000000 00000000 0000000d 00000000 0007fa28 0000000d 000acc88 00000004
	[   37.511718] 9fa0: c000e544 c000e380 0007fa28 0000000d 00000001 000acc88 0000000d 00000000
	[   37.520294] 9fc0: 0007fa28 0000000d 000acc88 00000004 00000001 00000020 00000002 00000000
	[   37.528869] 9fe0: 00000000 beab8624 0000ea05 b6eaebac 600d0010 00000001 00000000 00000000
	[   37.537475] [<c00b408c>] (kfree+0x84/0x144) from [<c0236274>] (device_add+0x530/0x57c)
	[   37.545806] [<c0236274>] (device_add+0x530/0x57c) from [<c032fa40>] (iio_device_register+0x8c8/0x990)
	[   37.555480] [<c032fa40>] (iio_device_register+0x8c8/0x990) from [<c0330164>] (hmc5843_probe+0xec/0x114)
	[   37.565338] [<c0330164>] (hmc5843_probe+0xec/0x114) from [<c02ccfd8>] (i2c_device_probe+0xc4/0xf8)
	[   37.574737] [<c02ccfd8>] (i2c_device_probe+0xc4/0xf8) from [<c02381a8>] (driver_probe_device+0x118/0x218)
	[   37.584777] [<c02381a8>] (driver_probe_device+0x118/0x218) from [<c0236bb0>] (bus_for_each_drv+0x4c/0x84)
	[   37.594818] [<c0236bb0>] (bus_for_each_drv+0x4c/0x84) from [<c0238030>] (device_attach+0x78/0xa4)
	[   37.604125] [<c0238030>] (device_attach+0x78/0xa4) from [<c02377ec>] (bus_probe_device+0x28/0x9c)
	[   37.613433] [<c02377ec>] (bus_probe_device+0x28/0x9c) from [<c0236138>] (device_add+0x3f4/0x57c)
	[   37.622650] [<c0236138>] (device_add+0x3f4/0x57c) from [<c02cd634>] (i2c_new_device+0xf8/0x19c)
	[   37.631805] [<c02cd634>] (i2c_new_device+0xf8/0x19c) from [<c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130)
	[   37.641754] [<c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130) from [<c0234d88>] (dev_attr_store+0x18/0x24)
	[   37.651611] [<c0234d88>] (dev_attr_store+0x18/0x24) from [<c010c354>] (sysfs_write_file+0x10c/0x140)
	[   37.661193] [<c010c354>] (sysfs_write_file+0x10c/0x140) from [<c00b7bf8>] (vfs_write+0xb0/0x178)
	[   37.670410] [<c00b7bf8>] (vfs_write+0xb0/0x178) from [<c00b7ed8>] (sys_write+0x3c/0x68)
	[   37.678833] [<c00b7ed8>] (sys_write+0x3c/0x68) from [<c000e380>] (ret_fast_syscall+0x0/0x3c)
	[   37.687683] Code: 1593301c e5932000 e3120080 1a000000 (e7f001f2)
	[   37.700775] ---[ end trace aaf805debdb69390 ]---

Client data was assigned to iio_dev structure in probe but in
hmc5843_init_client function casted to private driver data structure which
is wrong. Possibly calling mutex_init(&data->lock); corrupt data
which the lead to above crash.

Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
c48fca4
Ben Arblaster andatche referenced this pull request from a commit in andatche/raspi-linux December 16, 2011
usbfs: Fix oops related to user namespace conversion.
When running the Point Grey "flycap" program for their USB 3.0 camera
(which was running as a USB 2.0 device for some reason), I trigger this
oops whenever I try to open a video stream:

Dec 15 16:48:34 puck kernel: [ 1798.715559] BUG: unable to handle kernel NULL pointer dereference at           (null)
Dec 15 16:48:34 puck kernel: [ 1798.719153] IP: [<ffffffff8147841e>] free_async+0x1e/0x70
Dec 15 16:48:34 puck kernel: [ 1798.720991] PGD 6f833067 PUD 6fc56067 PMD 0
Dec 15 16:48:34 puck kernel: [ 1798.722815] Oops: 0002 [#1] SMP
Dec 15 16:48:34 puck kernel: [ 1798.724627] CPU 0
Dec 15 16:48:34 puck kernel: [ 1798.724636] Modules linked in: ecryptfs encrypted_keys sha1_generic trusted binfmt_misc sha256_generic aesni_intel cryptd aes_x86_64 aes_generic parport_pc dm_crypt ppdev joydev snd_hda_codec_hdmi snd_hda_codec_conexant arc4 iwlwifi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm thinkpad_acpi mac80211 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer btusb uvcvideo snd_seq_device bluetooth videodev psmouse snd v4l2_compat_ioctl32 serio_raw tpm_tis cfg80211 tpm tpm_bios nvram soundcore snd_page_alloc lp parport i915 xhci_hcd ahci libahci drm_kms_helper drm sdhci_pci sdhci e1000e i2c_algo_bit video
Dec 15 16:48:34 puck kernel: [ 1798.734212]
Dec 15 16:48:34 puck kernel: [ 1798.736162] Pid: 2713, comm: FlyCap2 Not tainted 3.2.0-rc5+ #28 LENOVO 4286CTO/4286CTO
Dec 15 16:48:34 puck kernel: [ 1798.738148] RIP: 0010:[<ffffffff8147841e>]  [<ffffffff8147841e>] free_async+0x1e/0x70
Dec 15 16:48:34 puck kernel: [ 1798.740134] RSP: 0018:ffff88005715fd78  EFLAGS: 00010296
Dec 15 16:48:34 puck kernel: [ 1798.742118] RAX: 00000000fffffff4 RBX: ffff88006fe8f900 RCX: 0000000000004118
Dec 15 16:48:34 puck kernel: [ 1798.744116] RDX: 0000000001000000 RSI: 0000000000016390 RDI: 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.746087] RBP: ffff88005715fd88 R08: 0000000000000000 R09: ffffffff8146f22e
Dec 15 16:48:34 puck kernel: [ 1798.748018] R10: ffff88006e520ac0 R11: 0000000000000001 R12: ffff88005715fe28
Dec 15 16:48:34 puck kernel: [ 1798.749916] R13: ffff88005d31df00 R14: ffff88006fe8f900 R15: 00007f688c995cb8
Dec 15 16:48:34 puck kernel: [ 1798.751785] FS:  00007f68a366da40(0000) GS:ffff880100200000(0000) knlGS:0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.753659] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Dec 15 16:48:34 puck kernel: [ 1798.755509] CR2: 0000000000000000 CR3: 00000000706bb000 CR4: 00000000000406f0
Dec 15 16:48:34 puck kernel: [ 1798.757334] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.759124] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Dec 15 16:48:34 puck kernel: [ 1798.760871] Process FlyCap2 (pid: 2713, threadinfo ffff88005715e000, task ffff88006c675b80)
Dec 15 16:48:34 puck kernel: [ 1798.762605] Stack:
Dec 15 16:48:34 puck kernel: [ 1798.764297]  ffff88005715fe28 0000000000000000 ffff88005715fe08 ffffffff81479058
Dec 15 16:48:34 puck kernel: [ 1798.766020]  0000000000000000 ffffea0000004000 ffff880000004118 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.767750]  ffff880000000001 ffff88006e520ac0 fffffff46fd81180 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.769472] Call Trace:
Dec 15 16:48:34 puck kernel: [ 1798.771147]  [<ffffffff81479058>] proc_do_submiturb+0x778/0xa00
Dec 15 16:48:34 puck kernel: [ 1798.772798]  [<ffffffff8147a5fd>] usbdev_do_ioctl+0x24d/0x1200
Dec 15 16:48:34 puck kernel: [ 1798.774410]  [<ffffffff8147b5de>] usbdev_ioctl+0xe/0x20
Dec 15 16:48:34 puck kernel: [ 1798.775975]  [<ffffffff81189259>] do_vfs_ioctl+0x99/0x600
Dec 15 16:48:34 puck kernel: [ 1798.777534]  [<ffffffff81189851>] sys_ioctl+0x91/0xa0
Dec 15 16:48:34 puck kernel: [ 1798.779088]  [<ffffffff816247c2>] system_call_fastpath+0x16/0x1b
ec 15 16:48:34 puck kernel: [ 1798.780634] Code: 51 ff ff ff e9 29 ff ff ff 0f 1f 40 00 55 48 89 e5 53 48 83 ec 08 66 66 66 66 90 48 89 fb 48 8b 7f 18 e8 a6 ea c0 ff 4
8 8b 7b 20 <f0> ff 0f 0f 94 c0 84 c0 74 05 e8 d3 99 c1 ff 48 8b 43 40 48 8b
Dec 15 16:48:34 puck kernel: [ 1798.783970] RIP  [<ffffffff8147841e>] free_async+0x1e/0x70
Dec 15 16:48:34 puck kernel: [ 1798.785630]  RSP <ffff88005715fd78>
Dec 15 16:48:34 puck kernel: [ 1798.787274] CR2: 0000000000000000
Dec 15 16:48:34 puck kernel: [ 1798.794728] ---[ end trace 52894d3355f88d19 ]---

markup_oops.pl says the oops is in put_cred:

 ffffffff81478401:      48 89 e5                mov    %rsp,%rbp
 ffffffff81478404:      53                      push   %rbx
 ffffffff81478405:      48 83 ec 08             sub    $0x8,%rsp
 ffffffff81478409:      e8 f2 c0 1a 00          callq  ffffffff81624500 <mcount>
 ffffffff8147840e:      48 89 fb                mov    %rdi,%rbx   |  %ebx => ffff88006fe8f900
        put_pid(as->pid);
 ffffffff81478411:      48 8b 7f 18             mov    0x18(%rdi),%rdi
 ffffffff81478415:      e8 a6 ea c0 ff          callq  ffffffff81086ec0 <put_pid>
        put_cred(as->cred);
 ffffffff8147841a:      48 8b 7b 20             mov    0x20(%rbx),%rdi |  %edi => 0  %ebx = ffff88006fe8f900
  */
 static inline int atomic_dec_and_test(atomic_t *v)
 {
        unsigned char c;

        asm volatile(LOCK_PREFIX "decl %0; sete %1"
*ffffffff8147841e:      f0 ff 0f                lock decl (%rdi)   |  %edi = 0 <--- faulting instruction
 ffffffff81478421:      0f 94 c0                sete   %al
 static inline void put_cred(const struct cred *_cred)
 {
        struct cred *cred = (struct cred *) _cred;

        validate_creds(cred);
        if (atomic_dec_and_test(&(cred)->usage))
 ffffffff81478424:      84 c0                   test   %al,%al
 ffffffff81478426:      74 05                   je     ffffffff8147842d <free_async+0x2d>
                __put_cred(cred);
 ffffffff81478428:      e8 d3 99 c1 ff          callq  ffffffff81091e00 <__put_cred>
        kfree(as->urb->transfer_buffer);
 ffffffff8147842d:      48 8b 43 40             mov    0x40(%rbx),%rax
 ffffffff81478431:      48 8b 78 68             mov    0x68(%rax),%rdi
 ffffffff81478435:      e8 a6 e1 ce ff          callq  ffffffff811665e0 <kfree>
        kfree(as->urb->setup_packet);
 ffffffff8147843a:      48 8b 43 40             mov    0x40(%rbx),%rax
 ffffffff8147843e:      48 8b b8 90 00 00 00    mov    0x90(%rax),%rdi
 ffffffff81478445:      e8 96 e1 ce ff          callq  ffffffff811665e0 <kfree>
        usb_free_urb(as->urb);
 ffffffff8147844a:      48 8b 7b 40             mov    0x40(%rbx),%rdi
 ffffffff8147844e:      e8 0d 6b ff ff          callq  ffffffff8146ef60 <usb_free_urb>

This bug seems to have been introduced by commit
d178bc3a708f39cbfefc3fab37032d3f2511b4ec "user namespace: usb: make usb
urbs user namespace aware (v2)"

I'm not sure if this is right fix, but it does stop the oops.

Unfortunately, the Point Grey software still refuses to work, but it's a
closed source app, so I can't fix it.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1b41c83
Ben Arblaster andatche referenced this pull request from a commit in andatche/raspi-linux April 12, 2012
Marek Belisko staging: iio: hmc5843: Fix crash in probe function.
commit 62d2feb upstream.

Fix crash after issuing:
	echo hmc5843 0x1e > /sys/class/i2c-dev/i2c-2/device/new_device

	[   37.180999] device: '2-001e': device_add
	[   37.188293] bus: 'i2c': add device 2-001e
	[   37.194549] PM: Adding info for i2c:2-001e
	[   37.200958] bus: 'i2c': driver_probe_device: matched device 2-001e with driver hmc5843
	[   37.210815] bus: 'i2c': really_probe: probing driver hmc5843 with device 2-001e
	[   37.224884] HMC5843 initialized
	[   37.228759] ------------[ cut here ]------------
	[   37.233612] kernel BUG at mm/slab.c:505!
	[   37.237701] Internal error: Oops - BUG: 0 [#1] PREEMPT
	[   37.243103] Modules linked in:
	[   37.246337] CPU: 0    Not tainted  (3.3.1-gta04+ #28)
	[   37.251647] PC is at kfree+0x84/0x144
	[   37.255493] LR is at kfree+0x20/0x144
	[   37.259338] pc : [<c00b408c>]    lr : [<c00b4028>]    psr: 40000093
	[   37.259368] sp : de249cd8  ip : 0000000c  fp : 00000090
	[   37.271362] r10: 0000000a  r9 : de229eac  r8 : c0236274
	[   37.276855] r7 : c09d6490  r6 : a0000013  r5 : de229c00  r4 : de229c10
	[   37.283691] r3 : c0f00218  r2 : 00000400  r1 : c0eea000  r0 : c00b4028
	[   37.290527] Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
	[   37.298095] Control: 10c5387d  Table: 9e1d0019  DAC: 00000015
	[   37.304107] Process sh (pid: 91, stack limit = 0xde2482f0)
	[   37.309844] Stack: (0xde249cd8 to 0xde24a000)
	[   37.314422] 9cc0:                                                       de229c10 de229c00
	[   37.322998] 9ce0: de229c10 ffffffea 00000005 c0236274 de140a80 c00b4798 dec00080 de140a80
	[   37.331573] 9d00: c032f37c dec00080 000080d0 00000001 de229c00 de229c10 c048d578 00000005
	[   37.340148] 9d20: de229eac 0000000a 00000090 c032fa40 00000001 00000000 00000001 de229c10
	[   37.348724] 9d40: de229eac 00000029 c075b558 00000001 00000003 00000004 de229c10 c048d594
	[   37.357299] 9d60: 00000000 60000013 00000018 205b0007 37332020 3432322e 5d343838 c0060020
	[   37.365905] 9d80: de251600 00000001 00000000 de251600 00000001 c0065a84 de229c00 de229c48
	[   37.374481] 9da0: 00000006 0048d62c de229c38 de229c00 de229c00 de1f6c00 de1f6c20 00000001
	[   37.383056] 9dc0: 00000000 c048d62c 00000000 de229c00 de229c00 de1f6c00 de1f6c20 00000001
	[   37.391632] 9de0: 00000000 c048d62c 00000000 c0330164 00000000 de1f6c20 c048d62c de1f6c00
	[   37.400207] 9e00: c0330078 de1f6c04 c078d714 de189b58 00000000 c02ccfd8 de1f6c20 c0795f40
	[   37.408782] 9e20: c0238330 00000000 00000000 c02381a8 de1b9fc0 de1f6c20 de1f6c20 de249e48
	[   37.417358] 9e40: c0238330 c0236bb0 decdbed8 de7d0f14 de1f6c20 de1f6c20 de1f6c54 de1f6c20
	[   37.425933] 9e60: 00000000 c0238030 de1f6c20 c078d7bc de1f6c20 c02377ec de1f6c20 de1f6c28
	[   37.434509] 9e80: dee64cb0 c0236138 c047c554 de189b58 00000000 c004b45c de1f6c20 de1f6cd8
	[   37.443084] 9ea0: c0edfa6c de1f6c00 dee64c68 de1f6c04 de1f6c20 dee64cb8 c047c554 de189b58
	[   37.451690] 9ec0: 00000000 c02cd634 dee64c68 de249ef4 de23b008 dee64cb0 0000000d de23b000
	[   37.460266] 9ee0: de23b007 c02cd78c 00000002 00000000 00000000 35636d68 00333438 00000000
	[   37.468841] 9f00: 00000000 00000000 001e0000 00000000 00000000 00000000 00000000 0a10cec0
	[   37.477416] 9f20: 00000002 de249f80 0000000d dee62990 de189b40 c0234d88 0000000d c010c354
	[   37.485992] 9f40: 0000000d de210f28 000acc88 de249f80 0000000d de248000 00000000 c00b7bf8
	[   37.494567] 9f60: de210f28 000acc88 de210f28 000acc88 00000000 00000000 0000000d c00b7ed8
	[   37.503143] 9f80: 00000000 00000000 0000000d 00000000 0007fa28 0000000d 000acc88 00000004
	[   37.511718] 9fa0: c000e544 c000e380 0007fa28 0000000d 00000001 000acc88 0000000d 00000000
	[   37.520294] 9fc0: 0007fa28 0000000d 000acc88 00000004 00000001 00000020 00000002 00000000
	[   37.528869] 9fe0: 00000000 beab8624 0000ea05 b6eaebac 600d0010 00000001 00000000 00000000
	[   37.537475] [<c00b408c>] (kfree+0x84/0x144) from [<c0236274>] (device_add+0x530/0x57c)
	[   37.545806] [<c0236274>] (device_add+0x530/0x57c) from [<c032fa40>] (iio_device_register+0x8c8/0x990)
	[   37.555480] [<c032fa40>] (iio_device_register+0x8c8/0x990) from [<c0330164>] (hmc5843_probe+0xec/0x114)
	[   37.565338] [<c0330164>] (hmc5843_probe+0xec/0x114) from [<c02ccfd8>] (i2c_device_probe+0xc4/0xf8)
	[   37.574737] [<c02ccfd8>] (i2c_device_probe+0xc4/0xf8) from [<c02381a8>] (driver_probe_device+0x118/0x218)
	[   37.584777] [<c02381a8>] (driver_probe_device+0x118/0x218) from [<c0236bb0>] (bus_for_each_drv+0x4c/0x84)
	[   37.594818] [<c0236bb0>] (bus_for_each_drv+0x4c/0x84) from [<c0238030>] (device_attach+0x78/0xa4)
	[   37.604125] [<c0238030>] (device_attach+0x78/0xa4) from [<c02377ec>] (bus_probe_device+0x28/0x9c)
	[   37.613433] [<c02377ec>] (bus_probe_device+0x28/0x9c) from [<c0236138>] (device_add+0x3f4/0x57c)
	[   37.622650] [<c0236138>] (device_add+0x3f4/0x57c) from [<c02cd634>] (i2c_new_device+0xf8/0x19c)
	[   37.631805] [<c02cd634>] (i2c_new_device+0xf8/0x19c) from [<c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130)
	[   37.641754] [<c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130) from [<c0234d88>] (dev_attr_store+0x18/0x24)
	[   37.651611] [<c0234d88>] (dev_attr_store+0x18/0x24) from [<c010c354>] (sysfs_write_file+0x10c/0x140)
	[   37.661193] [<c010c354>] (sysfs_write_file+0x10c/0x140) from [<c00b7bf8>] (vfs_write+0xb0/0x178)
	[   37.670410] [<c00b7bf8>] (vfs_write+0xb0/0x178) from [<c00b7ed8>] (sys_write+0x3c/0x68)
	[   37.678833] [<c00b7ed8>] (sys_write+0x3c/0x68) from [<c000e380>] (ret_fast_syscall+0x0/0x3c)
	[   37.687683] Code: 1593301c e5932000 e3120080 1a000000 (e7f001f2)
	[   37.700775] ---[ end trace aaf805debdb69390 ]---

Client data was assigned to iio_dev structure in probe but in
hmc5843_init_client function casted to private driver data structure which
is wrong. Possibly calling mutex_init(&data->lock); corrupt data
which the lead to above crash.

Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1b08b14
Erik Hemming erique referenced this pull request from a commit in erique/rpi_linux April 30, 2012
Roland Dreier cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
The driver calls cxgb_vlan_mode() from init_one().  This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets().  So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.

This was found because of the lockdep warning:

    INFO: trying to register non-static key.
    the code is fine but needs lockdep annotation.
    turning off the locking correctness validator.
    Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
    Call Trace:
     [<ffffffff8106e767>] register_lock_class+0x108/0x2d0
     [<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
     [<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
     [<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
     [<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
     [<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
     [<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
     [<ffffffff81042206>] do_work_for_cpu+0x10/0x22
     [<ffffffff810482de>] kthread+0xa1/0xa9
     [<ffffffff8138e234>] kernel_thread_helper+0x4/0x10

Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
60158e6
popcornmix popcornmix referenced this pull request from a commit February 22, 2012
x86: Remove some noise from boot log when starting cpus
Printing the "start_ip" for every secondary cpu is very noisy on a large
system - and doesn't add any value. Drop this message.

Console log before:
Booting Node   0, Processors  #1
smpboot cpu 1: start_ip = 96000
 #2
smpboot cpu 2: start_ip = 96000
 #3
smpboot cpu 3: start_ip = 96000
 #4
smpboot cpu 4: start_ip = 96000
       ...
 #31
smpboot cpu 31: start_ip = 96000
Brought up 32 CPUs

Console log after:
Booting Node   0, Processors  #1 #2 #3 #4 #5 #6 #7 Ok.
Booting Node   1, Processors  #8 #9 #10 #11 #12 #13 #14 #15 Ok.
Booting Node   0, Processors  #16 #17 #18 #19 #20 #21 #22 #23 Ok.
Booting Node   1, Processors  #24 #25 #26 #27 #28 #29 #30 #31
Brought up 32 CPUs

Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4f452eb42507460426@agluck-desktop.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
140f190
popcornmix popcornmix referenced this pull request from a commit April 12, 2012
Marek Belisko staging: iio: hmc5843: Fix crash in probe function.
Fix crash after issuing:
	echo hmc5843 0x1e > /sys/class/i2c-dev/i2c-2/device/new_device

	[   37.180999] device: '2-001e': device_add
	[   37.188293] bus: 'i2c': add device 2-001e
	[   37.194549] PM: Adding info for i2c:2-001e
	[   37.200958] bus: 'i2c': driver_probe_device: matched device 2-001e with driver hmc5843
	[   37.210815] bus: 'i2c': really_probe: probing driver hmc5843 with device 2-001e
	[   37.224884] HMC5843 initialized
	[   37.228759] ------------[ cut here ]------------
	[   37.233612] kernel BUG at mm/slab.c:505!
	[   37.237701] Internal error: Oops - BUG: 0 [#1] PREEMPT
	[   37.243103] Modules linked in:
	[   37.246337] CPU: 0    Not tainted  (3.3.1-gta04+ #28)
	[   37.251647] PC is at kfree+0x84/0x144
	[   37.255493] LR is at kfree+0x20/0x144
	[   37.259338] pc : [<c00b408c>]    lr : [<c00b4028>]    psr: 40000093
	[   37.259368] sp : de249cd8  ip : 0000000c  fp : 00000090
	[   37.271362] r10: 0000000a  r9 : de229eac  r8 : c0236274
	[   37.276855] r7 : c09d6490  r6 : a0000013  r5 : de229c00  r4 : de229c10
	[   37.283691] r3 : c0f00218  r2 : 00000400  r1 : c0eea000  r0 : c00b4028
	[   37.290527] Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
	[   37.298095] Control: 10c5387d  Table: 9e1d0019  DAC: 00000015
	[   37.304107] Process sh (pid: 91, stack limit = 0xde2482f0)
	[   37.309844] Stack: (0xde249cd8 to 0xde24a000)
	[   37.314422] 9cc0:                                                       de229c10 de229c00
	[   37.322998] 9ce0: de229c10 ffffffea 00000005 c0236274 de140a80 c00b4798 dec00080 de140a80
	[   37.331573] 9d00: c032f37c dec00080 000080d0 00000001 de229c00 de229c10 c048d578 00000005
	[   37.340148] 9d20: de229eac 0000000a 00000090 c032fa40 00000001 00000000 00000001 de229c10
	[   37.348724] 9d40: de229eac 00000029 c075b558 00000001 00000003 00000004 de229c10 c048d594
	[   37.357299] 9d60: 00000000 60000013 00000018 205b0007 37332020 3432322e 5d343838 c0060020
	[   37.365905] 9d80: de251600 00000001 00000000 de251600 00000001 c0065a84 de229c00 de229c48
	[   37.374481] 9da0: 00000006 0048d62c de229c38 de229c00 de229c00 de1f6c00 de1f6c20 00000001
	[   37.383056] 9dc0: 00000000 c048d62c 00000000 de229c00 de229c00 de1f6c00 de1f6c20 00000001
	[   37.391632] 9de0: 00000000 c048d62c 00000000 c0330164 00000000 de1f6c20 c048d62c de1f6c00
	[   37.400207] 9e00: c0330078 de1f6c04 c078d714 de189b58 00000000 c02ccfd8 de1f6c20 c0795f40
	[   37.408782] 9e20: c0238330 00000000 00000000 c02381a8 de1b9fc0 de1f6c20 de1f6c20 de249e48
	[   37.417358] 9e40: c0238330 c0236bb0 decdbed8 de7d0f14 de1f6c20 de1f6c20 de1f6c54 de1f6c20
	[   37.425933] 9e60: 00000000 c0238030 de1f6c20 c078d7bc de1f6c20 c02377ec de1f6c20 de1f6c28
	[   37.434509] 9e80: dee64cb0 c0236138 c047c554 de189b58 00000000 c004b45c de1f6c20 de1f6cd8
	[   37.443084] 9ea0: c0edfa6c de1f6c00 dee64c68 de1f6c04 de1f6c20 dee64cb8 c047c554 de189b58
	[   37.451690] 9ec0: 00000000 c02cd634 dee64c68 de249ef4 de23b008 dee64cb0 0000000d de23b000
	[   37.460266] 9ee0: de23b007 c02cd78c 00000002 00000000 00000000 35636d68 00333438 00000000
	[   37.468841] 9f00: 00000000 00000000 001e0000 00000000 00000000 00000000 00000000 0a10cec0
	[   37.477416] 9f20: 00000002 de249f80 0000000d dee62990 de189b40 c0234d88 0000000d c010c354
	[   37.485992] 9f40: 0000000d de210f28 000acc88 de249f80 0000000d de248000 00000000 c00b7bf8
	[   37.494567] 9f60: de210f28 000acc88 de210f28 000acc88 00000000 00000000 0000000d c00b7ed8
	[   37.503143] 9f80: 00000000 00000000 0000000d 00000000 0007fa28 0000000d 000acc88 00000004
	[   37.511718] 9fa0: c000e544 c000e380 0007fa28 0000000d 00000001 000acc88 0000000d 00000000
	[   37.520294] 9fc0: 0007fa28 0000000d 000acc88 00000004 00000001 00000020 00000002 00000000
	[   37.528869] 9fe0: 00000000 beab8624 0000ea05 b6eaebac 600d0010 00000001 00000000 00000000
	[   37.537475] [<c00b408c>] (kfree+0x84/0x144) from [<c0236274>] (device_add+0x530/0x57c)
	[   37.545806] [<c0236274>] (device_add+0x530/0x57c) from [<c032fa40>] (iio_device_register+0x8c8/0x990)
	[   37.555480] [<c032fa40>] (iio_device_register+0x8c8/0x990) from [<c0330164>] (hmc5843_probe+0xec/0x114)
	[   37.565338] [<c0330164>] (hmc5843_probe+0xec/0x114) from [<c02ccfd8>] (i2c_device_probe+0xc4/0xf8)
	[   37.574737] [<c02ccfd8>] (i2c_device_probe+0xc4/0xf8) from [<c02381a8>] (driver_probe_device+0x118/0x218)
	[   37.584777] [<c02381a8>] (driver_probe_device+0x118/0x218) from [<c0236bb0>] (bus_for_each_drv+0x4c/0x84)
	[   37.594818] [<c0236bb0>] (bus_for_each_drv+0x4c/0x84) from [<c0238030>] (device_attach+0x78/0xa4)
	[   37.604125] [<c0238030>] (device_attach+0x78/0xa4) from [<c02377ec>] (bus_probe_device+0x28/0x9c)
	[   37.613433] [<c02377ec>] (bus_probe_device+0x28/0x9c) from [<c0236138>] (device_add+0x3f4/0x57c)
	[   37.622650] [<c0236138>] (device_add+0x3f4/0x57c) from [<c02cd634>] (i2c_new_device+0xf8/0x19c)
	[   37.631805] [<c02cd634>] (i2c_new_device+0xf8/0x19c) from [<c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130)
	[   37.641754] [<c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130) from [<c0234d88>] (dev_attr_store+0x18/0x24)
	[   37.651611] [<c0234d88>] (dev_attr_store+0x18/0x24) from [<c010c354>] (sysfs_write_file+0x10c/0x140)
	[   37.661193] [<c010c354>] (sysfs_write_file+0x10c/0x140) from [<c00b7bf8>] (vfs_write+0xb0/0x178)
	[   37.670410] [<c00b7bf8>] (vfs_write+0xb0/0x178) from [<c00b7ed8>] (sys_write+0x3c/0x68)
	[   37.678833] [<c00b7ed8>] (sys_write+0x3c/0x68) from [<c000e380>] (ret_fast_syscall+0x0/0x3c)
	[   37.687683] Code: 1593301c e5932000 e3120080 1a000000 (e7f001f2)
	[   37.700775] ---[ end trace aaf805debdb69390 ]---

Client data was assigned to iio_dev structure in probe but in
hmc5843_init_client function casted to private driver data structure which
is wrong. Possibly calling mutex_init(&data->lock); corrupt data
which the lead to above crash.

Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
62d2feb
popcornmix popcornmix referenced this pull request from a commit July 18, 2012
cfg80211: Fix mutex locking in reg_last_request_cell_base
should fix the following issue

	[ 3229.815012] [ BUG: lock held when returning to user space! ]
	[ 3229.815016] 3.5.0-rc7-wl #28 Tainted: G        W  O
	[ 3229.815017]
	------------------------------------------------
	[ 3229.815019] wpa_supplicant/5783 is leaving the kernel with locks still held!
	[ 3229.815022] 1 lock held by wpa_supplicant/5783:
	[ 3229.815023]  #0: (reg_mutex){+.+.+.}, at: [<fa65834d>]
	reg_last_request_cell_base+0x1d/0x60 [cfg80211]

Cc: Luis Rodriguez <mcgrof@gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ebd0fd2
Stephen Warren swarren referenced this pull request from a commit in swarren/linux-rpi March 19, 2013
xen/acpi-processor: Don't dereference struct acpi_processor on all CPUs.
With git commit c705c78
"acpi: Export the acpi_processor_get_performance_info" we are now
using a different mechanism to access the P-states.

The acpi_processor per-cpu structure is set and filtered by the
core ACPI code which shrinks the per_cpu contents to only online CPUs.
In the past we would call acpi_processor_register_performance()
which would have not tried to dereference offline cpus.

With the new patch and the fact that the loop we take is for
for_all_possible_cpus we end up crashing on some machines.
We could modify the loop to be for online_cpus - but all the other
loops in the code use possible_cpus (for a good reason) - so lets
leave it as so and just check if per_cpu(processor) is NULL.

With this patch we will bypass the !online but possible CPUs.
This fixes:

IP: [<ffffffffa00d13b5>] xen_acpi_processor_init+0x1b6/0xe01 [xen_acpi_processor]
PGD 4126e6067 PUD 4126e3067 PMD 0
Oops: 0002 [#1] SMP
Pid: 432, comm: modprobe Not tainted 3.9.0-rc3+ #28 To be filled by O.E.M. To be filled by O.E.M./M5A97
RIP: e030:[<ffffffffa00d13b5>]  [<ffffffffa00d13b5>] xen_acpi_processor_init+0x1b6/0xe01 [xen_acpi_processor]
RSP: e02b:ffff88040c8a3ce8  EFLAGS: 00010282
.. snip..
Call Trace:
 [<ffffffffa00d11ff>] ? read_acpi_id+0x12b/0x12b [xen_acpi_processor]
 [<ffffffff8100215a>] do_one_initcall+0x12a/0x180
 [<ffffffff810c42c3>] load_module+0x1cd3/0x2870
 [<ffffffff81319b70>] ? ddebug_proc_open+0xc0/0xc0
 [<ffffffff810c4f37>] sys_init_module+0xd7/0x120
 [<ffffffff8166ce19>] system_call_fastpath+0x16/0x1b

on some machines.

Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
949dd8c
Stephen Warren swarren referenced this pull request from a commit in swarren/linux-rpi September 05, 2013
cifs: ensure that srv_mutex is held when dealing with ssocket pointer
Oleksii reported that he had seen an oops similar to this:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ipt_MASQUERADE xt_REDIRECT xt_tcpudp iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack ip_tables x_tables carl9170 ath usb_storage f2fs nfnetlink_log nfnetlink md4 cifs dns_resolver hid_generic usbhid hid af_packet uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core videodev rfcomm btusb bnep bluetooth qmi_wwan qcserial cdc_wdm usb_wwan usbnet usbserial mii snd_hda_codec_hdmi snd_hda_codec_realtek iwldvm mac80211 coretemp intel_powerclamp kvm_intel kvm iwlwifi snd_hda_intel cfg80211 snd_hda_codec xhci_hcd e1000e ehci_pci snd_hwdep sdhci_pci snd_pcm ehci_hcd microcode psmouse sdhci thinkpad_acpi mmc_core i2c_i801 pcspkr usbcore hwmon snd_timer snd_page_alloc snd ptp rfkill pps_core soundcore evdev usb_common vboxnetflt(O) vboxdrv(O)Oops#2 Part8
 loop tun binfmt_misc fuse msr acpi_call(O) ipv6 autofs4
CPU: 0 PID: 21612 Comm: kworker/0:1 Tainted: G        W  O 3.10.1SIGN #28
Hardware name: LENOVO 2306CTO/2306CTO, BIOS G2ET92WW (2.52 ) 02/22/2013
Workqueue: cifsiod cifs_echo_request [cifs]
task: ffff8801e1f416f0 ti: ffff880148744000 task.ti: ffff880148744000
RIP: 0010:[<ffffffff814dcc13>]  [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
RSP: 0000:ffff880148745b00  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880148745b78 RCX: 0000000000000048
RDX: ffff880148745c90 RSI: ffff880181864a00 RDI: ffff880148745b78
RBP: ffff880148745c48 R08: 0000000000000048 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff880181864a00
R13: ffff880148745c90 R14: 0000000000000048 R15: 0000000000000048
FS:  0000000000000000(0000) GS:ffff88021e200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000088 CR3: 000000020c42c000 CR4: 00000000001407b0
Oops#2 Part7
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
 ffff880148745b30 ffffffff810c4af9 0000004848745b30 ffff880181864a00
 ffffffff81ffbc40 0000000000000000 ffff880148745c90 ffffffff810a5aab
 ffff880148745bc0 ffffffff81ffbc40 ffff880148745b60 ffffffff815a9fb8
Call Trace:
 [<ffffffff810c4af9>] ? finish_task_switch+0x49/0xe0
 [<ffffffff810a5aab>] ? lock_timer_base.isra.36+0x2b/0x50
 [<ffffffff815a9fb8>] ? _raw_spin_unlock_irqrestore+0x18/0x40
 [<ffffffff810a673f>] ? try_to_del_timer_sync+0x4f/0x70
 [<ffffffff815aa38f>] ? _raw_spin_unlock_bh+0x1f/0x30
 [<ffffffff814dcc87>] kernel_sendmsg+0x37/0x50
 [<ffffffffa081a0e0>] smb_send_kvec+0xd0/0x1d0 [cifs]
 [<ffffffffa081a263>] smb_send_rqst+0x83/0x1f0 [cifs]
 [<ffffffffa081ab6c>] cifs_call_async+0xec/0x1b0 [cifs]
 [<ffffffffa08245e0>] ? free_rsp_buf+0x40/0x40 [cifs]
Oops#2 Part6
 [<ffffffffa082606e>] SMB2_echo+0x8e/0xb0 [cifs]
 [<ffffffffa0808789>] cifs_echo_request+0x79/0xa0 [cifs]
 [<ffffffff810b45b3>] process_one_work+0x173/0x4a0
 [<ffffffff810b52a1>] worker_thread+0x121/0x3a0
 [<ffffffff810b5180>] ? manage_workers.isra.27+0x2b0/0x2b0
 [<ffffffff810bae00>] kthread+0xc0/0xd0
 [<ffffffff810bad40>] ? kthread_create_on_node+0x120/0x120
 [<ffffffff815b199c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810bad40>] ? kthread_create_on_node+0x120/0x120
Code: 84 24 b8 00 00 00 4c 89 f1 4c 89 ea 4c 89 e6 48 89 df 4c 89 60 18 48 c7 40 28 00 00 00 00 4c 89 68 30 44 89 70 14 49 8b 44 24 28 <ff> 90 88 00 00 00 3d ef fd ff ff 74 10 48 8d 65 e0 5b 41 5c 41
 RIP  [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
 RSP <ffff880148745b00>
CR2: 0000000000000088

The client was in the middle of trying to send a frame when the
server->ssocket pointer got zeroed out. In most places, that we access
that pointer, the srv_mutex is held. There's only one spot that I see
that the server->ssocket pointer gets set and the srv_mutex isn't held.
This patch corrects that.

The upstream bug report was here:

    https://bugzilla.kernel.org/show_bug.cgi?id=60557

Cc: <stable@vger.kernel.org>
Reported-by: Oleksii Shevchuk <alxchk@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
73e216a
popcornmix popcornmix referenced this pull request from a commit September 05, 2013
cifs: ensure that srv_mutex is held when dealing with ssocket pointer
commit 73e216a upstream.

Oleksii reported that he had seen an oops similar to this:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ipt_MASQUERADE xt_REDIRECT xt_tcpudp iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack ip_tables x_tables carl9170 ath usb_storage f2fs nfnetlink_log nfnetlink md4 cifs dns_resolver hid_generic usbhid hid af_packet uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core videodev rfcomm btusb bnep bluetooth qmi_wwan qcserial cdc_wdm usb_wwan usbnet usbserial mii snd_hda_codec_hdmi snd_hda_codec_realtek iwldvm mac80211 coretemp intel_powerclamp kvm_intel kvm iwlwifi snd_hda_intel cfg80211 snd_hda_codec xhci_hcd e1000e ehci_pci snd_hwdep sdhci_pci snd_pcm ehci_hcd microcode psmouse sdhci thinkpad_acpi mmc_core i2c_i801 pcspkr usbcore hwmon snd_timer snd_page_alloc snd ptp rfkill pps_core soundcore evdev usb_common vboxnetflt(O) vboxdrv(O)Oops#2 Part8
 loop tun binfmt_misc fuse msr acpi_call(O) ipv6 autofs4
CPU: 0 PID: 21612 Comm: kworker/0:1 Tainted: G        W  O 3.10.1SIGN #28
Hardware name: LENOVO 2306CTO/2306CTO, BIOS G2ET92WW (2.52 ) 02/22/2013
Workqueue: cifsiod cifs_echo_request [cifs]
task: ffff8801e1f416f0 ti: ffff880148744000 task.ti: ffff880148744000
RIP: 0010:[<ffffffff814dcc13>]  [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
RSP: 0000:ffff880148745b00  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880148745b78 RCX: 0000000000000048
RDX: ffff880148745c90 RSI: ffff880181864a00 RDI: ffff880148745b78
RBP: ffff880148745c48 R08: 0000000000000048 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff880181864a00
R13: ffff880148745c90 R14: 0000000000000048 R15: 0000000000000048
FS:  0000000000000000(0000) GS:ffff88021e200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000088 CR3: 000000020c42c000 CR4: 00000000001407b0
Oops#2 Part7
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
 ffff880148745b30 ffffffff810c4af9 0000004848745b30 ffff880181864a00
 ffffffff81ffbc40 0000000000000000 ffff880148745c90 ffffffff810a5aab
 ffff880148745bc0 ffffffff81ffbc40 ffff880148745b60 ffffffff815a9fb8
Call Trace:
 [<ffffffff810c4af9>] ? finish_task_switch+0x49/0xe0
 [<ffffffff810a5aab>] ? lock_timer_base.isra.36+0x2b/0x50
 [<ffffffff815a9fb8>] ? _raw_spin_unlock_irqrestore+0x18/0x40
 [<ffffffff810a673f>] ? try_to_del_timer_sync+0x4f/0x70
 [<ffffffff815aa38f>] ? _raw_spin_unlock_bh+0x1f/0x30
 [<ffffffff814dcc87>] kernel_sendmsg+0x37/0x50
 [<ffffffffa081a0e0>] smb_send_kvec+0xd0/0x1d0 [cifs]
 [<ffffffffa081a263>] smb_send_rqst+0x83/0x1f0 [cifs]
 [<ffffffffa081ab6c>] cifs_call_async+0xec/0x1b0 [cifs]
 [<ffffffffa08245e0>] ? free_rsp_buf+0x40/0x40 [cifs]
Oops#2 Part6
 [<ffffffffa082606e>] SMB2_echo+0x8e/0xb0 [cifs]
 [<ffffffffa0808789>] cifs_echo_request+0x79/0xa0 [cifs]
 [<ffffffff810b45b3>] process_one_work+0x173/0x4a0
 [<ffffffff810b52a1>] worker_thread+0x121/0x3a0
 [<ffffffff810b5180>] ? manage_workers.isra.27+0x2b0/0x2b0
 [<ffffffff810bae00>] kthread+0xc0/0xd0
 [<ffffffff810bad40>] ? kthread_create_on_node+0x120/0x120
 [<ffffffff815b199c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810bad40>] ? kthread_create_on_node+0x120/0x120
Code: 84 24 b8 00 00 00 4c 89 f1 4c 89 ea 4c 89 e6 48 89 df 4c 89 60 18 48 c7 40 28 00 00 00 00 4c 89 68 30 44 89 70 14 49 8b 44 24 28 <ff> 90 88 00 00 00 3d ef fd ff ff 74 10 48 8d 65 e0 5b 41 5c 41
 RIP  [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
 RSP <ffff880148745b00>
CR2: 0000000000000088

The client was in the middle of trying to send a frame when the
server->ssocket pointer got zeroed out. In most places, that we access
that pointer, the srv_mutex is held. There's only one spot that I see
that the server->ssocket pointer gets set and the srv_mutex isn't held.
This patch corrects that.

The upstream bug report was here:

    https://bugzilla.kernel.org/show_bug.cgi?id=60557

Reported-by: Oleksii Shevchuk <alxchk@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
9b8ace6
popcornmix popcornmix referenced this pull request from a commit September 05, 2013
cifs: ensure that srv_mutex is held when dealing with ssocket pointer
commit 73e216a upstream.

Oleksii reported that he had seen an oops similar to this:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ipt_MASQUERADE xt_REDIRECT xt_tcpudp iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack ip_tables x_tables carl9170 ath usb_storage f2fs nfnetlink_log nfnetlink md4 cifs dns_resolver hid_generic usbhid hid af_packet uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core videodev rfcomm btusb bnep bluetooth qmi_wwan qcserial cdc_wdm usb_wwan usbnet usbserial mii snd_hda_codec_hdmi snd_hda_codec_realtek iwldvm mac80211 coretemp intel_powerclamp kvm_intel kvm iwlwifi snd_hda_intel cfg80211 snd_hda_codec xhci_hcd e1000e ehci_pci snd_hwdep sdhci_pci snd_pcm ehci_hcd microcode psmouse sdhci thinkpad_acpi mmc_core i2c_i801 pcspkr usbcore hwmon snd_timer snd_page_alloc snd ptp rfkill pps_core soundcore evdev usb_common vboxnetflt(O) vboxdrv(O)Oops#2 Part8
 loop tun binfmt_misc fuse msr acpi_call(O) ipv6 autofs4
CPU: 0 PID: 21612 Comm: kworker/0:1 Tainted: G        W  O 3.10.1SIGN #28
Hardware name: LENOVO 2306CTO/2306CTO, BIOS G2ET92WW (2.52 ) 02/22/2013
Workqueue: cifsiod cifs_echo_request [cifs]
task: ffff8801e1f416f0 ti: ffff880148744000 task.ti: ffff880148744000
RIP: 0010:[<ffffffff814dcc13>]  [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
RSP: 0000:ffff880148745b00  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880148745b78 RCX: 0000000000000048
RDX: ffff880148745c90 RSI: ffff880181864a00 RDI: ffff880148745b78
RBP: ffff880148745c48 R08: 0000000000000048 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff880181864a00
R13: ffff880148745c90 R14: 0000000000000048 R15: 0000000000000048
FS:  0000000000000000(0000) GS:ffff88021e200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000088 CR3: 000000020c42c000 CR4: 00000000001407b0
Oops#2 Part7
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
 ffff880148745b30 ffffffff810c4af9 0000004848745b30 ffff880181864a00
 ffffffff81ffbc40 0000000000000000 ffff880148745c90 ffffffff810a5aab
 ffff880148745bc0 ffffffff81ffbc40 ffff880148745b60 ffffffff815a9fb8
Call Trace:
 [<ffffffff810c4af9>] ? finish_task_switch+0x49/0xe0
 [<ffffffff810a5aab>] ? lock_timer_base.isra.36+0x2b/0x50
 [<ffffffff815a9fb8>] ? _raw_spin_unlock_irqrestore+0x18/0x40
 [<ffffffff810a673f>] ? try_to_del_timer_sync+0x4f/0x70
 [<ffffffff815aa38f>] ? _raw_spin_unlock_bh+0x1f/0x30
 [<ffffffff814dcc87>] kernel_sendmsg+0x37/0x50
 [<ffffffffa081a0e0>] smb_send_kvec+0xd0/0x1d0 [cifs]
 [<ffffffffa081a263>] smb_send_rqst+0x83/0x1f0 [cifs]
 [<ffffffffa081ab6c>] cifs_call_async+0xec/0x1b0 [cifs]
 [<ffffffffa08245e0>] ? free_rsp_buf+0x40/0x40 [cifs]
Oops#2 Part6
 [<ffffffffa082606e>] SMB2_echo+0x8e/0xb0 [cifs]
 [<ffffffffa0808789>] cifs_echo_request+0x79/0xa0 [cifs]
 [<ffffffff810b45b3>] process_one_work+0x173/0x4a0
 [<ffffffff810b52a1>] worker_thread+0x121/0x3a0
 [<ffffffff810b5180>] ? manage_workers.isra.27+0x2b0/0x2b0
 [<ffffffff810bae00>] kthread+0xc0/0xd0
 [<ffffffff810bad40>] ? kthread_create_on_node+0x120/0x120
 [<ffffffff815b199c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810bad40>] ? kthread_create_on_node+0x120/0x120
Code: 84 24 b8 00 00 00 4c 89 f1 4c 89 ea 4c 89 e6 48 89 df 4c 89 60 18 48 c7 40 28 00 00 00 00 4c 89 68 30 44 89 70 14 49 8b 44 24 28 <ff> 90 88 00 00 00 3d ef fd ff ff 74 10 48 8d 65 e0 5b 41 5c 41
 RIP  [<ffffffff814dcc13>] sock_sendmsg+0x93/0xd0
 RSP <ffff880148745b00>
CR2: 0000000000000088

The client was in the middle of trying to send a frame when the
server->ssocket pointer got zeroed out. In most places, that we access
that pointer, the srv_mutex is held. There's only one spot that I see
that the server->ssocket pointer gets set and the srv_mutex isn't held.
This patch corrects that.

The upstream bug report was here:

    https://bugzilla.kernel.org/show_bug.cgi?id=60557

Reported-by: Oleksii Shevchuk <alxchk@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
62d627e
Stephen Warren swarren referenced this pull request from a commit in swarren/linux-rpi September 27, 2013
x86: Improve the printout of the SMP bootup CPU table
As the new x86 CPU bootup printout format code maintainer, I am
taking immediate action to improve and clean (and thus indulge
my OCD) the reporting of the cores when coming up online.

Fix padding to a right-hand alignment, cleanup code and bind
reporting width to the max number of supported CPUs on the
system, like this:

 [    0.074509] smpboot: Booting Node   0, Processors:      #1  #2  #3  #4  #5  #6  #7 OK
 [    0.644008] smpboot: Booting Node   1, Processors:  #8  #9 #10 #11 #12 #13 #14 #15 OK
 [    1.245006] smpboot: Booting Node   2, Processors: #16 #17 #18 #19 #20 #21 #22 #23 OK
 [    1.864005] smpboot: Booting Node   3, Processors: #24 #25 #26 #27 #28 #29 #30 #31 OK
 [    2.489005] smpboot: Booting Node   4, Processors: #32 #33 #34 #35 #36 #37 #38 #39 OK
 [    3.093005] smpboot: Booting Node   5, Processors: #40 #41 #42 #43 #44 #45 #46 #47 OK
 [    3.698005] smpboot: Booting Node   6, Processors: #48 #49 #50 #51 #52 #53 #54 #55 OK
 [    4.304005] smpboot: Booting Node   7, Processors: #56 #57 #58 #59 #60 #61 #62 #63 OK
 [    4.961413] Brought up 64 CPUs

and this:

 [    0.072367] smpboot: Booting Node   0, Processors:    #1 #2 #3 #4 #5 #6 #7 OK
 [    0.686329] Brought up 8 CPUs

Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Libin <huawei.libin@huawei.com>
Cc: wangyijing@huawei.com
Cc: fenghua.yu@intel.com
Cc: guohanjun@huawei.com
Cc: paul.gortmaker@windriver.com
Link: http://lkml.kernel.org/r/20130927143554.GF4422@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
646e29a
Stephen Warren swarren referenced this pull request from a commit in swarren/linux-rpi September 30, 2013
x86/boot: Further compress CPUs bootup message
Turn it into (for example):

[    0.073380] x86: Booting SMP configuration:
[    0.074005] .... node   #0, CPUs:          #1   #2   #3   #4   #5   #6   #7
[    0.603005] .... node   #1, CPUs:     #8   #9  #10  #11  #12  #13  #14  #15
[    1.200005] .... node   #2, CPUs:    #16  #17  #18  #19  #20  #21  #22  #23
[    1.796005] .... node   #3, CPUs:    #24  #25  #26  #27  #28  #29  #30  #31
[    2.393005] .... node   #4, CPUs:    #32  #33  #34  #35  #36  #37  #38  #39
[    2.996005] .... node   #5, CPUs:    #40  #41  #42  #43  #44  #45  #46  #47
[    3.600005] .... node   #6, CPUs:    #48  #49  #50  #51  #52  #53  #54  #55
[    4.202005] .... node   #7, CPUs:    #56  #57  #58  #59  #60  #61  #62  #63
[    4.811005] .... node   #8, CPUs:    #64  #65  #66  #67  #68  #69  #70  #71
[    5.421006] .... node   #9, CPUs:    #72  #73  #74  #75  #76  #77  #78  #79
[    6.032005] .... node  #10, CPUs:    #80  #81  #82  #83  #84  #85  #86  #87
[    6.648006] .... node  #11, CPUs:    #88  #89  #90  #91  #92  #93  #94  #95
[    7.262005] .... node  #12, CPUs:    #96  #97  #98  #99 #100 #101 #102 #103
[    7.865005] .... node  #13, CPUs:   #104 #105 #106 #107 #108 #109 #110 #111
[    8.466005] .... node  #14, CPUs:   #112 #113 #114 #115 #116 #117 #118 #119
[    9.073006] .... node  #15, CPUs:   #120 #121 #122 #123 #124 #125 #126 #127
[    9.679901] x86: Booted up 16 nodes, 128 CPUs

and drop useless elements.

Change num_digits() to hpa's division-avoiding, cell-phone-typed
version which he went at great lengths and pains to submit on a
Saturday evening.

Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: huawei.libin@huawei.com
Cc: wangyijing@huawei.com
Cc: fenghua.yu@intel.com
Cc: guohanjun@huawei.com
Cc: paul.gortmaker@windriver.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20130930095624.GB16383@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
a17bce4
Stephen Warren swarren referenced this pull request from a commit in swarren/linux-rpi September 29, 2013
Lars-Peter Clausen i2c: Remove redundant 'driver' field from the i2c_client struct
The 'driver' field of the i2c_client struct is redundant. The same data can be
accessed through to_i2c_driver(client->dev.driver). The generated code for both
approaches in more or less the same.

E.g. on ARM the expression client->driver->command(...) generates

		...
		ldr     r3, [r0, #28]
		ldr     r3, [r3, #32]
		blx     r3
		...

and the expression to_i2c_driver(client->dev.driver)->command(...) generates

		...
		ldr     r3, [r0, #160]
    	ldr     r3, [r3, #-4]
    	blx     r3
		...

Other architectures will generate similar code.

All users of the 'driver' field outside of the I2C core have already been
converted. So this only leaves the core itself. This patch converts the
remaining few users in the I2C core and then removes the 'driver' field from the
i2c_client struct.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
0acc2b3
Stephen Warren swarren referenced this pull request from a commit in swarren/linux-rpi January 01, 2014
bwidawsk drm/i915/ppgtt: Defer request freeing on reset
We need to defer the free request until the object/vma is capable of
being freed - or else we have a problem  when we try to destroy the
context.

The exact same issue is described and fixed here:
commit e207804
Author: Ben Widawsky <ben@bwidawsk.net>
Date:   Fri Dec 6 14:11:22 2013 -0800

    drm/i915: Defer request freeing

I had this fix previously, but decided not to keep it for some reason I
can no longer remember.

gem_reset_stats is a really good test at hitting the problem.

For the inquisitive:
[  170.516392] ------------[ cut here ]------------
[  170.517227] WARNING: CPU: 1 PID: 105 at drivers/gpu/drm/drm_mm.c:578 drm_mm_takedown+0x2e/0x30 [drm]()
[  170.518064] Memory manager not clean during takedown.
[  170.518941] CPU: 1 PID: 105 Comm: kworker/1:1 Not tainted 3.13.0-rc4-BEN+ #28
[  170.519787] Hardware name: Hewlett-Packard HP EliteBook 8470p/179B, BIOS 68ICF Ver. F.02 04/27/2012
[  170.520662] Call Trace:
[  170.521517]  [<ffffffff814f0589>] dump_stack+0x4e/0x7a
[  170.522373]  [<ffffffff81049e6d>] warn_slowpath_common+0x7d/0xa0
[  170.523227]  [<ffffffff81049edc>] warn_slowpath_fmt+0x4c/0x50
[  170.524079]  [<ffffffffa06c414e>] drm_mm_takedown+0x2e/0x30 [drm]
[  170.524934]  [<ffffffffa07213f3>] gen6_ppgtt_cleanup+0x23/0x110
[i915]
[  170.525777]  [<ffffffffa07837ed>] ppgtt_release.part.5+0x24/0x29
[i915]
[  170.526603]  [<ffffffffa071aaa5>] i915_gem_context_free+0x195/0x1a0
[i915]
[  170.527423]  [<ffffffffa071189d>] i915_gem_free_request+0x9d/0xb0
[i915]
[  170.528247]  [<ffffffffa0718af9>] i915_gem_reset+0x1f9/0x3f0 [i915]
[  170.529065]  [<ffffffffa0700cce>] i915_reset+0x4e/0x180 [i915]
[  170.529870]  [<ffffffffa070829d>] i915_error_work_func+0xcd/0x120
[i915]
[  170.530666]  [<ffffffff8106c13a>] process_one_work+0x1fa/0x6d0
[  170.531453]  [<ffffffff8106c0d8>] ? process_one_work+0x198/0x6d0
[  170.532230]  [<ffffffff8106c72b>] worker_thread+0x11b/0x3a0
[  170.532996]  [<ffffffff8106c610>] ? process_one_work+0x6d0/0x6d0
[  170.533771]  [<ffffffff810743ef>] kthread+0xff/0x120
[  170.534548]  [<ffffffff810742f0>] ? insert_kthread_work+0x80/0x80
[  170.535322]  [<ffffffff814f97ac>] ret_from_fork+0x7c/0xb0
[  170.536089]  [<ffffffff810742f0>] ? insert_kthread_work+0x80/0x80
[  170.536847] ---[ end trace 3d4c12892e42d58f ]---

v2: Whitespace fix. (Chris)

Note: This is a bug that only hits the ppgtt topic branch but I've
figured that doing the request cleanup in this order is generally the
right thing to do.

Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a code comment to clarify what's actually going on since
the lifetime rules aroung ppgtt cleanup are ... fuzzy a best atm. Also
add a note about why we need this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
1d62bee
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment

Showing 3 unique commits by 1 author.

May 21, 2012
Stephen Warren i2c: bcm2708: initial driver
I2C driver for the BCM2708 series, as used on the Raspberry Pi.

This driver supports 7-bit addressing, but not 10-bit. The HW supports
10-bit.

This driver does not support repeated starts. It's not clear from the
data sheet how to create repeated starts.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
9fd4298
Stephen Warren HACK: ARM: bcm2708: mux I2C0 onto GPIO0/1
Set up the GPIO/pinmux so that I2C0 is mux'd onto GPIOs 0/1, so that
the controller can actually communicate with the outside world.

Ideally, this would be set up using pinctrl, but that doesn't exist
in this old kernel.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
a61933c
Stephen Warren ARM: bcm2708: instantiate I2C0 device
The BCM2708 has 3 I2C adapters. This change instantiates the first of
these, which is attached to the expansion header on the Raspberry Pi.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
dbf3ef5
This page is out of date. Refresh to see the latest.
26  arch/arm/mach-bcm2708/bcm2708.c
@@ -104,6 +104,11 @@ static struct map_desc bcm2708_io_desc[] __initdata = {
104 104
 	 .type = MT_DEVICE},
105 105
 #endif
106 106
 	{
  107
+	 .virtual = IO_ADDRESS(I2C0_BASE),
  108
+	 .pfn = __phys_to_pfn(I2C0_BASE),
  109
+	 .length = SZ_4K,
  110
+	 .type = MT_DEVICE},
  111
+	{
107 112
 	 .virtual = IO_ADDRESS(DMA_BASE),
108 113
 	 .pfn = __phys_to_pfn(DMA_BASE),
109 114
 	 .length = SZ_4K,
@@ -304,6 +309,26 @@ static struct platform_device bcm2708_uart1_device = {
304 309
 		},
305 310
 };
306 311
 
  312
+static struct resource bcm2708_i2c0_resources[] = {
  313
+	{
  314
+		.start = I2C0_BASE,
  315
+		.end = I2C0_BASE + SZ_4K - 1,
  316
+		.flags = IORESOURCE_MEM,
  317
+	},
  318
+	{
  319
+		.start = IRQ_I2C,
  320
+		.end = IRQ_I2C,
  321
+		.flags = IORESOURCE_IRQ,
  322
+	}
  323
+};
  324
+
  325
+static struct platform_device bcm2708_i2c0_device = {
  326
+	.name = "i2c-bcm2708",
  327
+	.id = 0,
  328
+	.resource = bcm2708_i2c0_resources,
  329
+	.num_resources = ARRAY_SIZE(bcm2708_i2c0_resources),
  330
+};
  331
+
307 332
 static struct resource bcm2708_usb_resources[] = {
308 333
 	[0] = {
309 334
 	       .start = USB_BASE,
@@ -491,6 +516,7 @@ void __init bcm2708_init(void)
491 516
 	bcm_register_device(&bcm2708_fb_device);
492 517
 	bcm_register_device(&bcm2708_usb_device);
493 518
 	bcm_register_device(&bcm2708_uart1_device);
  519
+	bcm_register_device(&bcm2708_i2c0_device);
494 520
 	bcm_register_device(&bcm2708_powerman_device);
495 521
 #ifdef CONFIG_MMC_SDHCI_BCM2708
496 522
 	bcm_register_device(&bcm2708_emmc_device);
4  arch/arm/mach-bcm2708/bcm2708_gpio.c
@@ -273,6 +273,10 @@ static int bcm2708_gpio_probe(struct platform_device *dev)
273 273
 	ucb->gc.set = bcm2708_gpio_set;
274 274
 	ucb->gc.can_sleep = 0;
275 275
 
  276
+	/* Hack: Set GPIOs 0/1 to ALT0 (I2C0) */
  277
+	bcm2708_set_function(&ucb->gc, 0, GPIO_FSEL_ALT0);
  278
+	bcm2708_set_function(&ucb->gc, 1, GPIO_FSEL_ALT0);
  279
+
276 280
 	err = gpiochip_add(&ucb->gc);
277 281
 	if (err)
278 282
 		goto err;
1  arch/arm/mach-bcm2708/include/mach/platform.h
@@ -63,6 +63,7 @@
63 63
 #define GPIO_BASE                (BCM2708_PERI_BASE + 0x200000) /* GPIO */
64 64
 #define UART0_BASE               (BCM2708_PERI_BASE + 0x201000)	/* Uart 0 */
65 65
 #define MMCI0_BASE               (BCM2708_PERI_BASE + 0x202000) /* MMC interface */
  66
+#define I2C0_BASE                (BCM2708_PERI_BASE + 0x205000)
66 67
 #define UART1_BASE               (BCM2708_PERI_BASE + 0x215000) /* Uart 1 */
67 68
 #define EMMC_BASE                (BCM2708_PERI_BASE + 0x300000) /* eMMC interface */
68 69
 #define SMI_BASE		 (BCM2708_PERI_BASE + 0x600000) /* SMI */
12  drivers/i2c/busses/Kconfig
@@ -687,6 +687,18 @@ config I2C_EG20T
687 687
 	  ML7213/ML7223 is companion chip for Intel Atom E6xx series.
688 688
 	  ML7213/ML7223 is completely compatible for Intel EG20T PCH.
689 689
 
  690
+config I2C_BCM2708
  691
+	tristate "Broadcom BCM2708 I2C controller"
  692
+	depends on ARCH_BCM2708
  693
+	help
  694
+	  If you say yes to this option, support will be included for the
  695
+	  BCM2708 I2C controller.
  696
+
  697
+	  If you don't know what to do here, say N.
  698
+
  699
+	  This support is also available as a module.  If so, the module
  700
+	  will be called i2c-bcm2708.
  701
+
690 702
 comment "External I2C/SMBus adapter drivers"
691 703
 
692 704
 config I2C_DIOLAN_U2C
1  drivers/i2c/busses/Makefile
@@ -66,6 +66,7 @@ obj-$(CONFIG_I2C_VERSATILE)	+= i2c-versatile.o
66 66
 obj-$(CONFIG_I2C_OCTEON)	+= i2c-octeon.o
67 67
 obj-$(CONFIG_I2C_XILINX)	+= i2c-xiic.o
68 68
 obj-$(CONFIG_I2C_EG20T)         += i2c-eg20t.o
  69
+obj-$(CONFIG_I2C_BCM2708)	+= i2c-bcm2708.o
69 70
 
70 71
 # External I2C/SMBus adapter drivers
71 72
 obj-$(CONFIG_I2C_DIOLAN_U2C)	+= i2c-diolan-u2c.o
327  drivers/i2c/busses/i2c-bcm2708.c
... ...
@@ -0,0 +1,327 @@
  1
+/*
  2
+ * BCM2708 master mode driver
  3
+ *
  4
+ * This software is licensed under the terms of the GNU General Public
  5
+ * License version 2, as published by the Free Software Foundation, and
  6
+ * may be copied, distributed, and modified under those terms.
  7
+ *
  8
+ * This program is distributed in the hope that it will be useful,
  9
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
  10
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  11
+ * GNU General Public License for more details.
  12
+ */
  13
+
  14
+#include <linux/clk.h>
  15
+#include <linux/completion.h>
  16
+#include <linux/err.h>
  17
+#include <linux/i2c.h>
  18
+#include <linux/interrupt.h>
  19
+#include <linux/io.h>
  20
+#include <linux/module.h>
  21
+#include <linux/platform_device.h>
  22
+#include <linux/slab.h>
  23
+
  24
+#define BCM2708_I2C_C		0x0
  25
+#define BCM2708_I2C_S		0x4
  26
+#define BCM2708_I2C_DLEN	0x8
  27
+#define BCM2708_I2C_A		0xc
  28
+#define BCM2708_I2C_FIFO	0x10
  29
+#define BCM2708_I2C_DIV		0x14
  30
+#define BCM2708_I2C_DEL		0x18
  31
+#define BCM2708_I2C_CLKT	0x1c
  32
+
  33
+#define BCM2708_I2C_C_READ	BIT(0)
  34
+#define BCM2708_I2C_C_CLEAR	BIT(4) /* bits 4 and 5 both clear */
  35
+#define BCM2708_I2C_C_ST	BIT(7)
  36
+#define BCM2708_I2C_C_INTD	BIT(8)
  37
+#define BCM2708_I2C_C_INTT	BIT(9)
  38
+#define BCM2708_I2C_C_INTR	BIT(10)
  39
+#define BCM2708_I2C_C_I2CEN	BIT(15)
  40
+
  41
+#define BCM2708_I2C_S_TA	BIT(0)
  42
+#define BCM2708_I2C_S_DONE	BIT(1)
  43
+#define BCM2708_I2C_S_TXW	BIT(2)
  44
+#define BCM2708_I2C_S_RXR	BIT(3)
  45
+#define BCM2708_I2C_S_TXD	BIT(4)
  46
+#define BCM2708_I2C_S_RXD	BIT(5)
  47
+#define BCM2708_I2C_S_TXE	BIT(6)
  48
+#define BCM2708_I2C_S_RXF	BIT(7)
  49
+#define BCM2708_I2C_S_ERR	BIT(8)
  50
+#define BCM2708_I2C_S_CLKT	BIT(9)
  51
+#define BCM2708_I2C_S_LEN	BIT(10) /* Fake bit for SW error reporting */
  52
+
  53
+#define BCM2708_I2C_TIMEOUT (msecs_to_jiffies(1000))
  54
+
  55
+struct bcm2708_i2c_dev {
  56
+	struct device *dev;
  57
+	void __iomem *regs;
  58
+	struct i2c_adapter adapter;
  59
+	struct completion completion;
  60
+	u32 msg_err;
  61
+	u8 *msg_buf;
  62
+	size_t msg_buf_remaining;
  63
+};
  64
+
  65
+static inline void bcm2708_i2c_writel(struct bcm2708_i2c_dev *i2c_dev,
  66
+				      u32 reg, u32 val)
  67
+{
  68
+	writel(val, i2c_dev->regs + reg);
  69
+}
  70
+
  71
+static inline u32 bcm2708_i2c_readl(struct bcm2708_i2c_dev *i2c_dev, u32 reg)
  72
+{
  73
+	return __raw_readw(i2c_dev->regs + reg);
  74
+}
  75
+
  76
+static void bcm2708_fill_txfifo(struct bcm2708_i2c_dev *i2c_dev)
  77
+{
  78
+	u32 val;
  79
+
  80
+	for (;;) {
  81
+		if (!i2c_dev->msg_buf_remaining)
  82
+			return;
  83
+		val = bcm2708_i2c_readl(i2c_dev, BCM2708_I2C_S);
  84
+		if (!(val & BCM2708_I2C_S_TXD))
  85
+			break;
  86
+		bcm2708_i2c_writel(i2c_dev, BCM2708_I2C_FIFO,
  87
+				   *i2c_dev->msg_buf);
  88
+		i2c_dev->msg_buf++;
  89
+		i2c_dev->msg_buf_remaining--;
  90
+	}
  91
+}
  92
+
  93
+static void bcm2708_drain_rxfifo(struct bcm2708_i2c_dev *i2c_dev)
  94
+{
  95
+	u32 val;
  96
+
  97
+	for (;;) {
  98
+		if (!i2c_dev->msg_buf_remaining)
  99
+			return;
  100
+		val = bcm2708_i2c_readl(i2c_dev, BCM2708_I2C_S);
  101
+		if (!(val & BCM2708_I2C_S_RXD))
  102
+			break;
  103
+		*i2c_dev->msg_buf = bcm2708_i2c_readl(i2c_dev,
  104
+						      BCM2708_I2C_FIFO);
  105
+		i2c_dev->msg_buf++;
  106
+		i2c_dev->msg_buf_remaining--;
  107
+	}
  108
+}
  109
+
  110
+static irqreturn_t bcm2708_i2c_isr(int this_irq, void *data)
  111
+{
  112
+	struct bcm2708_i2c_dev *i2c_dev = data;
  113
+	u32 val, err;
  114
+
  115
+	val = bcm2708_i2c_readl(i2c_dev, BCM2708_I2C_S);
  116
+	bcm2708_i2c_writel(i2c_dev, BCM2708_I2C_S, val);
  117
+
  118
+	err = val & (BCM2708_I2C_S_CLKT | BCM2708_I2C_S_ERR);
  119
+	if (err) {
  120
+		i2c_dev->msg_err = err;
  121
+		complete(&i2c_dev->completion);
  122
+		return IRQ_HANDLED;
  123
+	}
  124
+
  125
+	if (val & BCM2708_I2C_S_RXD) {
  126
+		bcm2708_drain_rxfifo(i2c_dev);
  127
+		if (!(val & BCM2708_I2C_S_DONE))
  128
+			return IRQ_HANDLED;
  129
+	}
  130
+
  131
+	if (val & BCM2708_I2C_S_DONE) {
  132
+		if (i2c_dev->msg_buf_remaining)
  133
+			i2c_dev->msg_err = BCM2708_I2C_S_LEN;
  134
+		else
  135
+			i2c_dev->msg_err = 0;
  136
+		complete(&i2c_dev->completion);
  137
+		return IRQ_HANDLED;
  138
+	}
  139
+
  140
+	if (val & BCM2708_I2C_S_TXD) {
  141
+		bcm2708_fill_txfifo(i2c_dev);
  142
+		return IRQ_NONE;
  143
+	}
  144
+
  145
+	return IRQ_NONE;
  146
+}
  147
+
  148
+static int bcm2708_i2c_xfer_msg(struct bcm2708_i2c_dev *i2c_dev,
  149
+				struct i2c_msg *msg)
  150
+{
  151
+	u32 c;
  152
+	int ret;
  153
+
  154
+	if (msg->len == 0)
  155
+		return -EINVAL;
  156
+
  157
+	i2c_dev->msg_buf = msg->buf;
  158
+	i2c_dev->msg_buf_remaining = msg->len;
  159
+	INIT_COMPLETION(i2c_dev->completion);
  160
+
  161
+	bcm2708_i2c_writel(i2c_dev, BCM2708_I2C_C, BCM2708_I2C_C_CLEAR);
  162
+
  163
+	if (msg->flags & I2C_M_RD) {
  164
+		c = BCM2708_I2C_C_READ | BCM2708_I2C_C_INTR;
  165
+	} else {
  166
+		c = BCM2708_I2C_C_INTT;
  167
+		bcm2708_fill_txfifo(i2c_dev);
  168
+	}
  169
+	c |= BCM2708_I2C_C_ST | BCM2708_I2C_C_INTD | BCM2708_I2C_C_I2CEN;
  170
+
  171
+	bcm2708_i2c_writel(i2c_dev, BCM2708_I2C_A, msg->addr);
  172
+	bcm2708_i2c_writel(i2c_dev, BCM2708_I2C_DLEN, msg->len);
  173
+	bcm2708_i2c_writel(i2c_dev, BCM2708_I2C_C, c);
  174
+
  175
+	ret = wait_for_completion_timeout(&i2c_dev->completion,
  176
+					  BCM2708_I2C_TIMEOUT);
  177
+	bcm2708_i2c_writel(i2c_dev, BCM2708_I2C_C, BCM2708_I2C_C_CLEAR);
  178
+	if (WARN_ON(ret == 0)) {
  179
+		dev_err(i2c_dev->dev, "i2c transfer timed out\n");
  180
+		return -ETIMEDOUT;
  181
+	}
  182
+
  183
+	if (likely(!i2c_dev->msg_err))
  184
+		return 0;
  185
+
  186
+	if ((i2c_dev->msg_err & BCM2708_I2C_S_ERR) &&
  187
+	    (msg->flags & I2C_M_IGNORE_NAK))
  188
+		return 0;
  189
+
  190
+	dev_err(i2c_dev->dev, "i2c transfer failed: %x\n", i2c_dev->msg_err);
  191
+
  192
+	if (i2c_dev->msg_err & BCM2708_I2C_S_ERR)
  193
+		return -EREMOTEIO;
  194
+	else
  195
+		return -EIO;
  196
+}
  197
+
  198
+static int bcm2708_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
  199
+			    int num)
  200
+{
  201
+	struct bcm2708_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
  202
+	int i;
  203
+	int ret = 0;
  204
+
  205
+	for (i = 0; i < num; i++) {
  206
+		ret = bcm2708_i2c_xfer_msg(i2c_dev, &msgs[i]);
  207
+		if (ret)
  208
+			break;
  209
+	}
  210
+
  211
+	return ret ?: i;
  212
+}
  213
+
  214
+static u32 bcm2708_i2c_func(struct i2c_adapter *adap)
  215
+{
  216
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
  217
+}
  218
+
  219
+static const struct i2c_algorithm bcm2708_i2c_algo = {
  220
+	.master_xfer	= bcm2708_i2c_xfer,
  221
+	.functionality	= bcm2708_i2c_func,
  222
+};
  223
+
  224
+static int __devinit bcm2708_i2c_probe(struct platform_device *pdev)
  225
+{
  226
+	struct bcm2708_i2c_dev *i2c_dev;
  227
+	struct resource *mem, *requested, *irq;
  228
+	int ret;
  229
+	struct i2c_adapter *adap;
  230
+
  231
+	i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
  232
+	if (!i2c_dev) {
  233
+		dev_err(&pdev->dev, "Cannot allocate i2c_dev\n");
  234
+		return -ENOMEM;
  235
+	}
  236
+	platform_set_drvdata(pdev, i2c_dev);
  237
+	i2c_dev->dev = &pdev->dev;
  238
+	init_completion(&i2c_dev->completion);
  239
+
  240
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
  241
+	if (!mem) {
  242
+		dev_err(&pdev->dev, "No mem resource\n");
  243
+		return -ENODEV;
  244
+	}
  245
+
  246
+	requested = devm_request_mem_region(&pdev->dev, mem->start,
  247
+					    resource_size(mem),
  248
+					    dev_name(&pdev->dev));
  249
+	if (!requested) {
  250
+		dev_err(&pdev->dev, "Could not claim register region\n");
  251
+		return -EBUSY;
  252
+	}
  253
+
  254
+	i2c_dev->regs = devm_ioremap(&pdev->dev, mem->start,
  255
+				     resource_size(mem));
  256
+	if (!i2c_dev->regs) {
  257
+		dev_err(&pdev->dev, "Could not map registers\n");
  258
+		return -ENOMEM;
  259
+	}
  260
+
  261
+	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
  262
+	if (!irq) {
  263
+		dev_err(&pdev->dev, "No IRQ resource\n");
  264
+		return -ENODEV;
  265
+	}
  266
+
  267
+	ret = devm_request_irq(&pdev->dev, irq->start, bcm2708_i2c_isr,
  268
+			       IRQF_SHARED, dev_name(&pdev->dev), i2c_dev);
  269
+	if (ret) {
  270
+		dev_err(&pdev->dev, "Could not request IRQ\n");
  271
+		return -ENODEV;
  272
+	}
  273
+
  274
+	adap = &i2c_dev->adapter;
  275
+	i2c_set_adapdata(adap, i2c_dev);
  276
+	adap->owner = THIS_MODULE;
  277
+	adap->class = I2C_CLASS_HWMON;
  278
+	strlcpy(adap->name, "bcm2708 I2C adapter", sizeof(adap->name));
  279
+	adap->algo = &bcm2708_i2c_algo;
  280
+	adap->dev.parent = &pdev->dev;
  281
+	adap->nr = -1;
  282
+
  283
+	bcm2708_i2c_writel(i2c_dev, BCM2708_I2C_C, 0);
  284
+
  285
+	ret = i2c_add_numbered_adapter(adap);
  286
+	if (ret) {
  287
+		dev_err(&pdev->dev, "Could not add adapter\n");
  288
+		return ret;
  289
+	}
  290
+
  291
+	return 0;
  292
+}
  293
+
  294
+static int bcm2708_i2c_remove(struct platform_device *pdev)
  295
+{
  296
+	struct bcm2708_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
  297
+
  298
+	i2c_del_adapter(&i2c_dev->adapter);
  299
+
  300
+	return 0;
  301
+}
  302
+
  303
+static struct platform_driver bcm2708_i2c_driver = {
  304
+	.probe		= bcm2708_i2c_probe,
  305
+	.remove		= bcm2708_i2c_remove,
  306
+	.driver		= {
  307
+		.name	= "i2c-bcm2708",
  308
+		.owner	= THIS_MODULE,
  309
+	},
  310
+};
  311
+
  312
+static int __init bcm2708_i2c_init_driver(void)
  313
+{
  314
+	return platform_driver_register(&bcm2708_i2c_driver);
  315
+}
  316
+module_init(bcm2708_i2c_init_driver);
  317
+
  318
+static void __exit bcm2708_i2c_exit_driver(void)
  319
+{
  320
+	platform_driver_unregister(&bcm2708_i2c_driver);
  321
+}
  322
+module_exit(bcm2708_i2c_exit_driver);
  323
+
  324
+MODULE_AUTHOR("Stephen Warren <swarren@wwwdotorg.org>");
  325
+MODULE_DESCRIPTION("BCM2708 I2C bus adapter");
  326
+MODULE_LICENSE("GPL v2");
  327
+MODULE_ALIAS("platform:i2c-bcm2708");
Commit_comment_tip

Tip: You can add notes to lines in a file. Hover to the left of a line to make a note

Something went wrong with that request. Please try again.