Skip to content

board_sam9_boot_linux_ru

Serge Vakulenko edited this page Aug 26, 2015 · 2 revisions

Протокол загрузки Linux на плате Starterkit SAM9-S3E:

RomBOOT
>Start AT91Bootstrap...
Copy application ...
Run ...


U-Boot 1.1.5 (Apr 29 2008 - 20:23:52)

DRAM:  64 MB
NAND:  NAND device: Manufacturer ID: 0xec, Chip ID: 0xda ( NAND 256MiB 3,3V 8-bit)
NAND: Pagesize: 2048, Blocksize: 128K, OOBsize: 64
256 MiB
DataFlash:AT45DB321
Nb pages:   8192
Page Size:    528
Size= 4325376 bytes
Logical address: 0xC0000000
Area 0: C0000000 to C0003FFF (RO)
Area 1: C0004000 to C0007FFF
Area 2: C0008000 to C0037FFF (RO)
Area 3: C0038000 to C041FFFF
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
KS8721 PHY Detected
No link
MAC: error during RMII initialization
Hit any key to stop autoboot:  0
## Booting image at 20400000 ...
   Image Name:   Linux Kernel Image
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    1422821 Bytes =  1.4 MB
   Load Address: 20008000
   Entry Point:  20008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.24 (root@armmaker) (gcc version 4.2.0 20070413 (prerelease) (CodeSourcery Sourcery G++ Lite 2007q1-10)) #91 Sat May 17 02:50:14 MSD 2008
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: StarterKit.ru SK-AT91SAM9XE512-S3E
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 200 MHz, master 100 MHz, main 12.000 MHz
CPU0: D VIVT write-back cache
CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: root=/dev/ram0 rw initrd=0x23100000,0x500000 console=ttyS0,115200 mem=64M
AT91: 96 gpio irqs in 3 banks
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 56832KB available (2612K code, 230K data, 116K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 64 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: pit clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 5120K
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
yaffs Apr 22 2008 10:39:18 Installing.
io scheduler noop registered (default)
atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
atmel_usart.2: ttyS2 at MMIO 0xfffb8000 (irq = 8) is a ATMEL_SERIAL
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
ssc ssc.0: Atmel SSC device at 0xc4870000 (irq 14)
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfffc4000 irq 21 (00:00:00:00:00:00)
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)
Driver 'sd' needs updating - please use bus_type methods
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
AT91 NAND: 8-bit, <NULL> ECC
Scanning device for bad blocks
Creating 2 MTD partitions on "at91_nand":
0x00000000-0x00800000 : "Partition 1"
0x00800000-0x10000000 : "Partition 2"
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12)
mtd_dataflash spi0.0: AT45DB321x (4224 KBytes)
usbmon: debugfs is not available
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
at91_ohci at91_ohci: irq 20, io mem 0x00500000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: at91_udc version 3 May 2006
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RAMDISK: Compressed image found at block 0
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 116K


Starting system...
mount: Mounting none on /dev/pts failed: No such file or directory
SIOCSIFFLAGS: Invalid argument
SIOCSIFFLAGS: Invalid argument
chgrp: unknown group name: utmp
yaffs: dev is 32505857 name is "mtdblock1"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.1, "mtdblock1"
yaffs: auto selecting yaffs2
yaffs: restored from checkpoint
umount: Couldn't umount /mnt/mmc: Invalid argument
rmmod: at91_mci: No such file or directory
mount: Mounting /dev/mmc1 on /mnt/mmc failed: No such device or address
mount: Mounting /dev/sda1 on /mnt/usb failed: No such device or
Please press Enter to activate this console.


BusyBox v1.1.2 (2008.04.21-23:55+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

[@SK-AT91SAM9 /]$mount
/dev/root on / type ext2 (rw)
none on /dev/shm type tmpfs (rw)
/proc on /proc type proc (rw)
/dev/mtdblock1 on /mnt/nand type yaffs (rw,sync)
[@SK-AT91SAM9 /]$df
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/ram0                 3963      3380       583  85% /
none                     31040         0     31040   0% /dev/shm
/dev/mtdblock1          253952      1152    252800   0% /mnt/nand
[@SK-AT91SAM9 /]$ps aux
  PID  Uid     VmSize Stat Command
    1 0           336 S   init
    2 0               SW< [kthreadd]
    3 0               SW< [ksoftirqd/0]
    4 0               SW< [watchdog/0]
    5 0               SW< [events/0]
    6 0               SW< [khelper]
   47 0               SW< [kblockd/0]
   60 0               SW< [khubd]
   65 0               SW< [kmmcd]
   86 0               SW  [pdflush]
   87 0               SW  [pdflush]
   88 0               SW< [kswapd0]
   89 0               SW< [aio/0]
  232 0               SW< [mtdblockd]
  233 0               SW< [nftld]
  265 0               SW< [rpciod/0]
  283 0            84 S   /bin/telnetd -l /bin/ash
  285 0            96 S   /bin/httpd -h /mnt/www
  301 0           444 S   -ash
  307 0           372 R   ps aux
[@SK-AT91SAM9 /]$
You can’t perform that action at this time.