Skip to content
Go to file
Cannot retrieve contributors at this time
279 lines (230 sloc) 8.61 KB



shadowsocks-libev - a lightweight and secure socks5 proxy


ss-local|ss-redir|ss-server|ss-tunnel|ss-manager [-s <server_host>] [-p <server_port>] [-l <local_port>] [-k <password>] [-m <encrypt_method>] [-f <pid_file>] [-t <timeout>] [-c <config_file>]


Shadowsocks-libev is a lightweight and secure socks5 proxy. It is a port of the original shadowsocks created by clowwindy. Shadowsocks-libev is written in pure C and takes advantage of libev to achieve both high performance and low resource consumption.

Shadowsocks-libev consists of five components. One is ss-server(1) that runs on a remote server to provide secured tunnel service. ss-local(1) and ss-redir(1) are clients on your local machines to proxy traffic(TCP/UDP or both). ss-tunnel(1) is a tool for local port forwarding.

While ss-local(1) works as a standard socks5 proxy, ss-redir(1) works as a transparent proxy and requires netfilter’s NAT module. For more information, check out the EXAMPLE section.

ss-manager(1) is a controller for multi-user management and traffic statistics, using UNIX domain socket to talk with ss-server(1). Also, it provides a UNIX domain socket or IP based API for other software. About the details of this API, please refer to the PROTOCOL section.


-s <server_host>

Set the server’s hostname or IP.

-l <local_port>

Set the local port number.

Not available in server nor manager mode.

-k <password>
--password <password>

Set the password. The server and the client should use the same password.

--key <key_in_base64>

Set the key directly. The key should be encoded with URL-safe Base64.

Not available in manager mode.

-m <encrypt_method>

Set the cipher.

Shadowsocks-libev accepts 19 different ciphers:

aes-128-gcm, aes-192-gcm, aes-256-gcm, rc4-md5, aes-128-cfb, aes-192-cfb, aes-256-cfb, aes-128-ctr, aes-192-ctr, aes-256-ctr, bf-cfb, camellia-128-cfb, camellia-192-cfb, camellia-256-cfb, chacha20-ietf-poly1305, xchacha20-ietf-poly1305, salsa20, chacha20 and chacha20-ietf.

The default cipher is chacha20-ietf-poly1305.

If built with PolarSSL or custom OpenSSL libraries, some of these ciphers may not work.

-a <user_name>

Run as a specific user.

-f <pid_file>

Start shadowsocks as a daemon with specific pid file.

-t <timeout>

Set the socket timeout in seconds. The default value is 60.

-c <config_file>

Use a configuration file.

-n <number>

Specify max number of open files.

Not available in manager mode.

Only available on Linux.

-i <interface>

Send traffic through specific network interface.

For example, there are three interfaces in your device, which is lo (, eth0 ( and eth1 ( Meanwhile, you configure shadowsocks-libev to listen on and bind to eth1. That results the traffic go out through eth1, but not lo nor eth0. This option is useful to control traffic in multi-interface environment.

Not available in redir mode.

-b <local_address>

Specify the local address to bind.

For servers: Specify the local address to use while this server is making outbound connections to remote servers on behalf of the clients.

For clients: Specify the local address to use while this client is making outbound connections to the server.

Not available in manager mode.


Enable UDP relay.

TPROXY is required in redir mode. You may need root permission.


Enable UDP relay and disable TCP relay.

Not available in local mode.


Use tproxy instead of redirect (for tcp).

Only available in redir mode.

-L <addr:port>

Specify destination server address and port for local port forwarding.

Only available in tunnel mode.

-d <addr>

Setup name servers for internal DNS resolver (libc-ares). The default server is fetched from /etc/resolv.conf.

Only available in server and manager mode.


Enable TCP fast open.

Not available in redir nor tunnel mode, with Linux kernel > 3.7.0.


Enable port reuse.

Only available with Linux kernel > 3.9.0.



--acl <acl_config>

Enable ACL (Access Control List) and specify config file.

Not available in redir nor tunnel mode.

--manager-address <path_to_unix_domain>

Specify UNIX domain socket address.

Only available in server and manager mode.

--executable <path_to_server_executable>

Specify the executable path of ss-server.

Only available in manager mode.


Enable verbose mode.


Print help message.


The config file is written in JSON and easy to edit.

The config file equivalent of command line options is listed as example below.

Command line JSON


"server": ""

-s -p 1234 (client)

"server": ""

-p 1234

"server_port": "1234"


"local_address": ""


"local_ipv4_address": ""

-b 2620:129:35::33

"local_ipv6_address": "2620:129:35::33"

-l 4321

"local_port": "4321"

-k "PasSworD"

"password": "PasSworD"

-m "aes-256-cfb"

"method": "aes-256-cfb"

-t 60

"timeout": 60

-a nobody

"user": "nobody"

--acl "/path/to/acl"

"acl": "/path/to/acl"


"fast_open": true


"reuse_port": true


"no_delay": true

--plugin "obfs-server"

"plugin": "obfs-server"

--plugin-opts "obfs=http"

"plugin_opts": "obfs=http"


"ipv6_first": true

-n "/etc/nofile"

"nofile": "/etc/nofile"

-d ""

"nameserver": ""

-L ""

"tunnel_address": ""


"mode": "tcp_and_udp"


"mode": "udp_only"

no "-u" nor "-U" options (default)

"mode": "tcp_only"


"tcp_tproxy": true

(only in ss-manager’s config)

"port_password": {"1234":"PasSworD"}