Skip to content

/ raspberrypi-documentation

forked from raspberrypi/documentation
Permalink
Branch: master

raspberrypi-documentation/hardware/computemodule/dt-blob-disp1-only.dts

Go to file
 
 
Cannot retrieve contributors at this time
998 lines (982 sloc) 38.5 KB
Raw Blame
/dts-v1/;
/ {
videocore {
pins_rev1 {
pin_config {
pin@default {
polarity = "active_high";
termination = "pull_down";
startup_state = "inactive";
function = "input";
}; // pin
pin@p2 { function = "i2c1"; termination = "pull_up"; }; // I2C 1 SDA
pin@p3 { function = "i2c1"; termination = "pull_up"; }; // I2C 1 SCL
pin@p5 { function = "output"; termination = "pull_down"; }; // CAM_LED
pin@p6 { function = "output"; termination = "pull_down"; }; // LAN NRESET
pin@p14 { function = "uart0"; termination = "no_pulling"; drive_strength_mA = < 8 >; }; // TX uart0
pin@p15 { function = "uart0"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // RX uart0
pin@p16 { function = "output"; termination = "pull_up"; polarity="active_low"; }; // activity LED
pin@p27 { function = "output"; termination = "no_pulling"; }; // Camera shutdown
pin@p40 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Left audio
pin@p45 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Right audio
pin@p46 { function = "input"; termination = "no_pulling"; }; // Hotplug
pin@p47 { function = "input"; termination = "no_pulling"; }; // SD_CARD_DETECT
pin@p48 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CLK
pin@p49 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CMD
pin@p50 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D0
pin@p51 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D1
pin@p52 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D2
pin@p53 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D3
}; // pin_config
pin_defines {
pin_define@HDMI_CONTROL_ATTACHED {
type = "internal";
number = <46>;
};
pin_define@NUM_CAMERAS {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_UNICAM_PORT {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_I2C_PORT {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_SDA_PIN {
type = "internal";
number = <2>;
};
pin_define@CAMERA_0_SCL_PIN {
type = "internal";
number = <3>;
};
pin_define@CAMERA_0_SHUTDOWN {
type = "internal";
number = <27>;
};
pin_define@CAMERA_0_LED {
type = "internal";
number = <5>;
};
pin_define@FLASH_0_ENABLE {
type = "absent";
};
pin_define@FLASH_0_INDICATOR {
type = "absent";
};
pin_define@FLASH_1_ENABLE {
type = "absent";
};
pin_define@FLASH_1_INDICATOR {
type = "absent";
};
pin_define@POWER_LOW {
type = "absent";
};
pin_define@LEDS_DISK_ACTIVITY {
type = "internal";
number = <16>;
};
pin_define@LAN_RUN {
type = "internal";
number = <6>;
};
pin_define@SMPS_SDA {
type = "absent";
};
pin_define@SMPS_SCL {
type = "absent";
};
pin_define@ETH_CLK {
type = "absent";
};
pin_define@USB_LIMIT_1A2 {
type = "absent";
};
pin_define@SIO_1V8_SEL {
type = "absent";
};
pin_define@PWML {
type = "internal";
number = <40>;
};
pin_define@PWMR {
type = "internal";
number = <45>;
};
pin_define@SAFE_MODE {
type = "internal";
number = <1>;
};
pin_define@SD_CARD_DETECT {
type = "internal";
number = <47>;
};
pin_define@ID_SDA {
type = "absent";
};
pin_define@ID_SCL {
type = "absent";
};
pin_define@DISPLAY_SDA {
type = "internal";
number = <2>;
};
pin_define@DISPLAY_SCL {
type = "internal";
number = <3>;
};
}; // pin_defines
}; // pins_rev1
pins_rev2 {
pin_config {
pin@default {
polarity = "active_high";
termination = "pull_down";
startup_state = "inactive";
function = "input";
}; // pin
pin@p0 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SDA
pin@p1 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SCL
pin@p5 { function = "output"; termination = "pull_down"; }; // CAM_LED
pin@p6 { function = "output"; termination = "pull_down"; }; // LAN NRESET
pin@p14 { function = "uart0"; termination = "no_pulling"; drive_strength_mA = < 8 >; }; // TX uart0
pin@p15 { function = "uart0"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // RX uart0
pin@p16 { function = "output"; termination = "pull_up"; polarity = "active_low"; }; // activity LED
pin@p21 { function = "output"; termination = "no_pulling"; }; // Camera shutdown
pin@p40 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Left audio
pin@p45 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Right audio
pin@p46 { function = "input"; termination = "no_pulling"; }; // Hotplug
pin@p47 { function = "input"; termination = "no_pulling"; }; // SD_CARD_DETECT
pin@p48 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CLK
pin@p49 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CMD
pin@p50 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D0
pin@p51 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D1
pin@p52 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D2
pin@p53 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D3
}; // pin_config
pin_defines {
pin_define@HDMI_CONTROL_ATTACHED {
type = "internal";
number = <46>;
};
pin_define@NUM_CAMERAS {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_I2C_PORT {
type = "internal";
number = <0>;
};
pin_define@CAMERA_0_SDA_PIN {
type = "internal";
number = <0>;
};
pin_define@CAMERA_0_SCL_PIN {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_SHUTDOWN {
type = "internal";
number = <21>;
};
pin_define@CAMERA_0_UNICAM_PORT {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_LED {
type = "internal";
number = <5>;
};
pin_define@FLASH_0_ENABLE {
type = "absent";
};
pin_define@FLASH_0_INDICATOR {
type = "absent";
};
pin_define@FLASH_1_ENABLE {
type = "absent";
};
pin_define@FLASH_1_INDICATOR {
type = "absent";
};
pin_define@POWER_LOW {
type = "absent";
};
pin_define@LEDS_DISK_ACTIVITY {
type = "internal";
number = <16>;
};
pin_define@LAN_RUN {
type = "internal";
number = <6>;
};
pin_define@SMPS_SDA {
type = "absent";
};
pin_define@SMPS_SCL {
type = "absent";
};
pin_define@ETH_CLK {
type = "absent";
};
pin_define@USB_LIMIT_1A2 {
type = "absent";
};
pin_define@SIO_1V8_SEL {
type = "absent";
};
pin_define@PWML {
type = "internal";
number = <40>;
};
pin_define@PWMR {
type = "internal";
number = <45>;
};
pin_define@SAFE_MODE {
type = "internal";
number = <3>;
};
pin_define@SD_CARD_DETECT {
type = "internal";
number = <47>;
};
pin_define@ID_SDA {
type = "absent";
};
pin_define@ID_SCL {
type = "absent";
};
pin_define@DISPLAY_SDA {
type = "internal";
number = <0>;
};
pin_define@DISPLAY_SCL {
type = "internal";
number = <1>;
};
}; // pin_defines
}; // pins
pins_bplus1 { // Pi 1 Model B+ rev 1.1
pin_config {
pin@default {
polarity = "active_high";
termination = "pull_down";
startup_state = "inactive";
function = "input";
}; // pin
pin@p14 { function = "uart0"; termination = "no_pulling"; drive_strength_mA = < 8 >; }; // TX uart0
pin@p15 { function = "uart0"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // RX uart0
pin@p28 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SDA
pin@p29 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SCL
pin@p31 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Power low
pin@p32 { function = "output"; termination = "pull_down"; }; // Camera LED
pin@p35 { function = "output"; termination = "pull_down"; }; // LAN_RUN
pin@p38 { function = "output"; termination = "no_pulling"; }; // USB current limit (0=600mA, 1=1200mA)
pin@p40 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Right audio
pin@p41 { function = "output"; termination = "no_pulling"; }; // Camera shutdown
pin@p44 { function = "gp_clk"; termination = "pull_down"; }; // ETH_CLK - Ethernet 25MHz output
pin@p45 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Left audio
pin@p46 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Hotplug
pin@p47 { function = "output"; termination = "pull_down"; }; // activity LED
pin@p48 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CLK
pin@p49 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CMD
pin@p50 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D0
pin@p51 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D1
pin@p52 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D2
pin@p53 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D3
}; // pin_config
pin_defines {
pin_define@HDMI_CONTROL_ATTACHED {
type = "internal";
number = <46>;
};
pin_define@NUM_CAMERAS {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_I2C_PORT {
type = "internal";
number = <0>;
};
pin_define@CAMERA_0_SDA_PIN {
type = "internal";
number = <28>;
};
pin_define@CAMERA_0_SCL_PIN {
type = "internal";
number = <29>;
};
pin_define@CAMERA_0_SHUTDOWN {
type = "internal";
number = <41>;
};
pin_define@CAMERA_0_UNICAM_PORT {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_LED {
type = "internal";
number = <32>;
};
pin_define@FLASH_0_ENABLE {
type = "absent";
};
pin_define@FLASH_0_INDICATOR {
type = "absent";
};
pin_define@FLASH_1_ENABLE {
type = "absent";
};
pin_define@FLASH_1_INDICATOR {
type = "absent";
};
pin_define@POWER_LOW {
type = "internal";
number = <31>;
};
pin_define@LEDS_DISK_ACTIVITY {
type = "internal";
number = <47>;
};
pin_define@LAN_RUN {
type = "internal";
number = <35>;
};
pin_define@SMPS_SDA {
type = "absent";
};
pin_define@SMPS_SCL {
type = "absent";
};
pin_define@ETH_CLK {
type = "internal";
number = <44>;
};
pin_define@USB_LIMIT_1A2 {
type = "absent";
};
pin_define@SIO_1V8_SEL {
type = "internal";
number = <38>;
};
pin_define@PWML {
type = "internal";
number = <45>;
};
pin_define@PWMR {
type = "internal";
number = <40>;
};
pin_define@SAFE_MODE {
type = "internal";
number = <3>;
};
pin_define@SD_CARD_DETECT {
type = "absent";
};
pin_define@ID_SDA {
type = "internal";
number = <0>;
};
pin_define@ID_SCL {
type = "internal";
number = <1>;
};
pin_define@DISPLAY_SDA {
type = "internal";
number = <28>;
};
pin_define@DISPLAY_SCL {
type = "internal";
number = <29>;
};
}; // pin_defines
}; // pins
pins_bplus2 { // Pi 1 Model B+ rev 1.2
pin_config {
pin@default {
polarity = "active_high";
termination = "pull_down";
startup_state = "inactive";
function = "input";
}; // pin
pin@p14 { function = "uart0"; termination = "no_pulling"; drive_strength_mA = < 8 >; }; // TX uart0
pin@p15 { function = "uart0"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // RX uart0
pin@p28 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SDA
pin@p29 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SCL
pin@p31 { function = "output"; termination = "pull_down"; }; // LAN_RUN
pin@p32 { function = "output"; termination = "pull_down"; }; // Camera LED
pin@p35 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Power low
pin@p38 { function = "output"; termination = "no_pulling"; }; // USB current limit (0=600mA, 1=1200mA)
pin@p40 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Right audio
pin@p41 { function = "output"; termination = "no_pulling"; }; // Camera shutdown
pin@p44 { function = "gp_clk"; termination = "pull_down"; }; // ETH_CLK - Ethernet 25MHz output
pin@p45 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Left audio
pin@p46 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Hotplug
pin@p47 { function = "output"; termination = "pull_down"; }; // activity LED
pin@p48 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CLK
pin@p49 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CMD
pin@p50 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D0
pin@p51 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D1
pin@p52 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D2
pin@p53 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D3
}; // pin_config
pin_defines {
pin_define@HDMI_CONTROL_ATTACHED {
type = "internal";
number = <46>;
};
pin_define@NUM_CAMERAS {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_I2C_PORT {
type = "internal";
number = <0>;
};
pin_define@CAMERA_0_SDA_PIN {
type = "internal";
number = <28>;
};
pin_define@CAMERA_0_SCL_PIN {
type = "internal";
number = <29>;
};
pin_define@CAMERA_0_SHUTDOWN {
type = "internal";
number = <41>;
};
pin_define@CAMERA_0_UNICAM_PORT {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_LED {
type = "internal";
number = <32>;
};
pin_define@FLASH_0_ENABLE {
type = "absent";
};
pin_define@FLASH_0_INDICATOR {
type = "absent";
};
pin_define@FLASH_1_ENABLE {
type = "absent";
};
pin_define@FLASH_1_INDICATOR {
type = "absent";
};
pin_define@POWER_LOW {
type = "internal";
number = <35>;
};
pin_define@LEDS_DISK_ACTIVITY {
type = "internal";
number = <47>;
};
pin_define@LAN_RUN {
type = "internal";
number = <31>;
};
pin_define@SMPS_SDA {
type = "absent";
};
pin_define@SMPS_SCL {
type = "absent";
};
pin_define@ETH_CLK {
type = "internal";
number = <44>;
};
pin_define@USB_LIMIT_1A2 {
type = "internal";
number = <38>;
};
pin_define@SIO_1V8_SEL {
type = "absent";
};
pin_define@PWML {
type = "internal";
number = <45>;
};
pin_define@PWMR {
type = "internal";
number = <40>;
};
pin_define@SAFE_MODE {
type = "internal";
number = <3>;
};
pin_define@SD_CARD_DETECT {
type = "absent";
};
pin_define@ID_SDA {
type = "internal";
number = <0>;
};
pin_define@ID_SCL {
type = "internal";
number = <1>;
};
pin_define@DISPLAY_SDA {
type = "internal";
number = <28>;
};
pin_define@DISPLAY_SCL {
type = "internal";
number = <29>;
};
}; // pin_defines
}; // pins
pins_aplus {
pin_config {
pin@default {
polarity = "active_high";
termination = "pull_down";
startup_state = "inactive";
function = "input";
}; // pin
pin@p14 { function = "uart0"; termination = "no_pulling"; drive_strength_mA = < 8 >; }; // TX uart0
pin@p15 { function = "uart0"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // RX uart0
pin@p28 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SDA
pin@p29 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SCL
pin@p32 { function = "output"; termination = "pull_down"; }; // Camera LED
pin@p35 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Power low
pin@p38 { function = "output"; termination = "no_pulling"; }; // USB current limit (0=600mA, 1=1200mA)
pin@p40 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Right audio
pin@p41 { function = "output"; termination = "no_pulling"; }; // Camera shutdown
pin@p45 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Left audio
pin@p46 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Hotplug
pin@p47 { function = "output"; termination = "pull_down"; }; // activity LED
pin@p48 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CLK
pin@p49 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CMD
pin@p50 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D0
pin@p51 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D1
pin@p52 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D2
pin@p53 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D3
}; // pin_config
pin_defines {
pin_define@HDMI_CONTROL_ATTACHED {
type = "internal";
number = <46>;
};
pin_define@NUM_CAMERAS {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_I2C_PORT {
type = "internal";
number = <0>;
};
pin_define@CAMERA_0_SDA_PIN {
type = "internal";
number = <28>;
};
pin_define@CAMERA_0_SCL_PIN {
type = "internal";
number = <29>;
};
pin_define@CAMERA_0_SHUTDOWN {
type = "internal";
number = <41>;
};
pin_define@CAMERA_0_UNICAM_PORT {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_LED {
type = "internal";
number = <32>;
};
pin_define@FLASH_0_ENABLE {
type = "absent";
};
pin_define@FLASH_0_INDICATOR {
type = "absent";
};
pin_define@FLASH_1_ENABLE {
type = "absent";
};
pin_define@FLASH_1_INDICATOR {
type = "absent";
};
pin_define@POWER_LOW {
type = "internal";
number = <35>;
};
pin_define@LEDS_DISK_ACTIVITY {
type = "internal";
number = <47>;
};
pin_define@LAN_RUN {
type = "absent";
};
pin_define@SMPS_SDA {
type = "absent";
};
pin_define@SMPS_SCL {
type = "absent";
};
pin_define@ETH_CLK {
type = "absent";
};
pin_define@USB_LIMIT_1A2 {
type = "internal";
number = <38>;
};
pin_define@SIO_1V8_SEL {
type = "absent";
};
pin_define@PWML {
type = "internal";
number = <45>;
};
pin_define@PWMR {
type = "internal";
number = <40>;
};
pin_define@SAFE_MODE {
type = "internal";
number = <3>;
};
pin_define@SD_CARD_DETECT {
type = "absent";
};
pin_define@ID_SDA {
type = "internal";
number = <0>;
};
pin_define@ID_SCL {
type = "internal";
number = <1>;
};
pin_define@DISPLAY_SDA {
type = "internal";
number = <28>;
};
pin_define@DISPLAY_SCL {
type = "internal";
number = <29>;
};
}; // pin_defines
}; // pins
pins_2b1 { // Pi 2 Model B rev 1.0
pin_config {
pin@default {
polarity = "active_high";
termination = "pull_down";
startup_state = "inactive";
function = "input";
}; // pin
pin@p14 { function = "uart0"; termination = "no_pulling"; drive_strength_mA = < 8 >; }; // TX uart0
pin@p15 { function = "uart0"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // RX uart0
pin@p28 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SDA / SMPS_SDA
pin@p29 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SCL / SMPS_SCL
pin@p31 { function = "output"; termination = "pull_down"; }; // LAN_RUN
pin@p32 { function = "output"; termination = "pull_down"; }; // Camera LED
pin@p35 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Power low
pin@p38 { function = "output"; termination = "no_pulling"; }; // USB current limit (0=600mA, 1=1200mA)
pin@p40 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Right audio
pin@p41 { function = "output"; termination = "no_pulling"; }; // Camera shutdown
pin@p44 { function = "gp_clk"; termination = "pull_down"; }; // ETH_CLK - Ethernet 25MHz output
pin@p45 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Left audio
pin@p46 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Hotplug
pin@p47 { function = "output"; termination = "pull_down"; }; // activity LED
pin@p48 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CLK
pin@p49 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CMD
pin@p50 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D0
pin@p51 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D1
pin@p52 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D2
pin@p53 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D3
}; // pin_config
pin_defines {
pin_define@HDMI_CONTROL_ATTACHED {
type = "internal";
number = <46>;
};
pin_define@NUM_CAMERAS {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_I2C_PORT {
type = "internal";
number = <0>;
};
pin_define@CAMERA_0_SDA_PIN {
type = "internal";
number = <28>;
};
pin_define@CAMERA_0_SCL_PIN {
type = "internal";
number = <29>;
};
pin_define@CAMERA_0_SHUTDOWN {
type = "internal";
number = <41>;
};
pin_define@CAMERA_0_UNICAM_PORT {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_LED {
type = "internal";
number = <32>;
};
pin_define@FLASH_0_ENABLE {
type = "absent";
};
pin_define@FLASH_0_INDICATOR {
type = "absent";
};
pin_define@FLASH_1_ENABLE {
type = "absent";
};
pin_define@FLASH_1_INDICATOR {
type = "absent";
};
pin_define@POWER_LOW {
type = "internal";
number = <35>;
};
pin_define@LEDS_DISK_ACTIVITY {
type = "internal";
number = <47>;
};
pin_define@LAN_RUN {
type = "internal";
number = <31>;
};
pin_define@SMPS_SDA {
type = "internal";
number = <28>;
};
pin_define@SMPS_SCL {
type = "internal";
number = <29>;
};
pin_define@ETH_CLK {
type = "internal";
number = <44>;
};
pin_define@USB_LIMIT_1A2 {
type = "internal";
number = <38>;
};
pin_define@SIO_1V8_SEL {
type = "absent";
};
pin_define@PWML {
type = "internal";
number = <45>;
};
pin_define@PWMR {
type = "internal";
number = <40>;
};
pin_define@SAFE_MODE {
type = "internal";
number = <3>;
};
pin_define@SD_CARD_DETECT {
type = "absent";
};
pin_define@ID_SDA {
type = "internal";
number = <0>;
};
pin_define@ID_SCL {
type = "internal";
number = <1>;
};
pin_define@DISPLAY_SDA {
type = "internal";
number = <28>;
};
pin_define@DISPLAY_SCL {
type = "internal";
number = <29>;
};
}; // pin_defines
}; // pins
pins_2b2 { // Pi 2 Model B rev 1.1
pin_config {
pin@default {
polarity = "active_high";
termination = "pull_down";
startup_state = "inactive";
function = "input";
}; // pin
pin@p14 { function = "uart0"; termination = "no_pulling"; drive_strength_mA = < 8 >; }; // TX uart0
pin@p15 { function = "uart0"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // RX uart0
// The firmware changes I2C pin functions on the fly, returning them to inputs when done. But pins 28&29 are
// not used on a 1.1 Pi2, so the I2C0 function ends up multiply mapped (bad). therefore don't statically map.
// pin@p28 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SDA
// pin@p29 { function = "i2c0"; termination = "pull_up"; }; // I2C 0 SCL
pin@p31 { function = "output"; termination = "pull_down"; }; // LAN_RUN
pin@p32 { function = "output"; termination = "pull_down"; }; // Camera LED
pin@p35 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Power low
pin@p38 { function = "output"; termination = "no_pulling"; }; // USB current limit (0=600mA, 1=1200mA)
pin@p40 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Right audio
pin@p41 { function = "output"; termination = "no_pulling"; }; // Camera shutdown
// Communicate with the SMPS by "bit-bashing" the I2C protocol on GPIOs 42 and 43
pin@p42 { function = "output"; termination = "pull_up"; }; // SMPS_SCL
pin@p43 { function = "input"; termination = "no_pulling"; }; // SMPS_SDA
pin@p44 { function = "gp_clk"; termination = "pull_down"; }; // ETH_CLK - Ethernet 25MHz output
pin@p45 { function = "pwm"; termination = "no_pulling"; drive_strength_mA = < 16 >; }; // Left audio
pin@p46 { function = "input"; termination = "no_pulling"; polarity = "active_low"; }; // Hotplug
pin@p47 { function = "output"; termination = "pull_down"; }; // activity LED
pin@p48 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CLK
pin@p49 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CMD
pin@p50 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D0
pin@p51 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D1
pin@p52 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D2
pin@p53 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D3
}; // pin_config
pin_defines {
pin_define@HDMI_CONTROL_ATTACHED {
type = "internal";
number = <46>;
};
pin_define@NUM_CAMERAS {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_I2C_PORT {
type = "internal";
number = <0>;
};
pin_define@CAMERA_0_SDA_PIN {
type = "internal";
number = <28>;
};
pin_define@CAMERA_0_SCL_PIN {
type = "internal";
number = <29>;
};
pin_define@CAMERA_0_SHUTDOWN {
type = "internal";
number = <41>;
};
pin_define@CAMERA_0_UNICAM_PORT {
type = "internal";
number = <1>;
};
pin_define@CAMERA_0_LED {
type = "internal";
number = <32>;
};
pin_define@FLASH_0_ENABLE {
type = "absent";
};
pin_define@FLASH_0_INDICATOR {
type = "absent";
};
pin_define@FLASH_1_ENABLE {
type = "absent";
};
pin_define@FLASH_1_INDICATOR {
type = "absent";
};
pin_define@POWER_LOW {
type = "internal";
number = <35>;
};
pin_define@LEDS_DISK_ACTIVITY {
type = "internal";
number = <47>;
};
pin_define@LAN_RUN {
type = "internal";
number = <31>;
};
pin_define@SMPS_SDA {
type = "internal";
number = <43>;
};
pin_define@SMPS_SCL {
type = "internal";
number = <42>;
};
pin_define@ETH_CLK {
type = "internal";
number = <44>;
};
pin_define@USB_LIMIT_1A2 {
type = "internal";
number = <38>;
};
pin_define@SIO_1V8_SEL {
type = "absent";
};
pin_define@PWML {
type = "internal";
number = <45>;
};
pin_define@PWMR {
type = "internal";
number = <40>;
};
pin_define@SAFE_MODE {
type = "internal";
number = <3>;
};
pin_define@SD_CARD_DETECT {
type = "absent";
};
pin_define@ID_SDA {
type = "internal";
number = <0>;
};
pin_define@ID_SCL {
type = "internal";
number = <1>;
};
pin_define@DISPLAY_SDA {
type = "internal";
number = <28>;
};
pin_define@DISPLAY_SCL {
type = "internal";
number = <29>;
};
}; // pin_defines
}; // pins
pins_cm {
pin_config {
pin@default {
polarity = "active_high";
termination = "pull_down";
startup_state = "inactive";
function = "input";
}; // pin
pin@p14 { function = "uart0"; termination = "no_pulling"; }; // TX uart0
pin@p15 { function = "uart0"; termination = "pull_up"; }; // RX uart0
pin@p48 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CLK
pin@p49 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD CMD
pin@p50 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D0
pin@p51 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D1
pin@p52 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D2
pin@p53 { function = "sdcard"; termination = "pull_up"; drive_strength_mA = < 8 >; }; // SD D3
}; // pin_config
pin_defines {
pin_define@DISPLAY_SDA {
type = "internal";
number = <0>;
};
pin_define@DISPLAY_SCL {
type = "internal";
number = <1>;
};
pin_define@DISPLAY_I2C_PORT {
type="internal";
number=<0>;
};
}; // pin_defines
}; // pins_cm
};
};
You can’t perform that action at this time.