Fetching contributors…
Cannot retrieve contributors at this time
107 lines (80 sloc) 4.06 KB
The compile-time configurable defaults for the Linux SCSI tape driver.
Copyright 1995 Kai Makisara.
Last modified: Wed Sep 2 21:24:07 1998 by root@home
Changed (and renamed) for OnStream SCSI drives garloff@suse.de
$Header: /cvsroot/osst/Driver/osst_options.h,v 1.6 2003/12/23 14:22:12 wriede Exp $
/* The minimum limit for the number of SCSI tape devices is determined by
OSST_MAX_TAPES. If the number of tape devices and the "slack" defined by
OSST_EXTRA_DEVS exceeds OSST_MAX_TAPES, the large number is used. */
#define OSST_MAX_TAPES 4
/* If OSST_IN_FILE_POS is nonzero, the driver positions the tape after the
record been read by the user program even if the tape has moved further
because of buffered reads. Should be set to zero to support also drives
that can't space backwards over records. NOTE: The tape will be
spaced backwards over an "accidentally" crossed filemark in any case. */
#define OSST_IN_FILE_POS 1
/* The tape driver buffer size in kilobytes. */
/* Don't change, as this is the HW blocksize */
/* The number of kilobytes of data in the buffer that triggers an
asynchronous write in fixed block mode. See also OSST_ASYNC_WRITES
below. */
/* OSST_EOM_RESERVE defines the number of frames are kept in reserve for
* * write error recovery when writing near end of medium. ENOSPC is returned
* * when write() is called and the tape write position is within this number
* * of blocks from the tape capacity. */
#define OSST_EOM_RESERVE 300
/* The maximum number of tape buffers the driver allocates. The number
is also constrained by the number of drives detected. Determines the
maximum number of concurrently active tape drives. */
/* Maximum number of scatter/gather segments */
/* Fit one buffer in pages and add one for the AUX header */
/* The number of scatter/gather segments to allocate at first try (must be
smaller or equal to the maximum). */
/* The size of the first scatter/gather segments (determines the maximum block
size for SCSI adapters not supporting scatter/gather). The default is set
to try to allocate the buffer as one chunk. */
/* The following lines define defaults for properties that can be set
separately for each drive using the MTSTOPTIONS ioctl. */
/* If OSST_TWO_FM is non-zero, the driver writes two filemarks after a
file being written. Some drives can't handle two filemarks at the
end of data. */
#define OSST_TWO_FM 0
/* If OSST_BUFFER_WRITES is non-zero, writes in fixed block mode are
buffered until the driver buffer is full or asynchronous write is
triggered. */
/* If OSST_ASYNC_WRITES is non-zero, the SCSI write command may be started
without waiting for it to finish. May cause problems in multiple
tape backups. */
/* If OSST_READ_AHEAD is non-zero, blocks are read ahead in fixed block
mode. */
/* If OSST_AUTO_LOCK is non-zero, the drive door is locked at the first
read or write command after the device is opened. The door is opened
when the device is closed. */
#define OSST_AUTO_LOCK 0
/* If OSST_FAST_MTEOM is non-zero, the MTEOM ioctl is done using the
direct SCSI command. The file number status is lost but this method
is fast with some drives. Otherwise MTEOM is done by spacing over
files and the file number status is retained. */
/* If OSST_SCSI2LOGICAL is nonzero, the logical block addresses are used for
MTIOCPOS and MTSEEK by default. Vendor addresses are used if OSST_SCSI2LOGICAL
is zero. */
/* If OSST_SYSV is non-zero, the tape behaves according to the SYS V semantics.
The default is BSD semantics. */
#define OSST_SYSV 0