Hardware_Specification_UP_Xtreme
- 4GB/8GB/16GB LPDDR4
- Intel® UHD Graphics 610 (Celeron)
- Intel® UHD Graphics 620 (Core-i)
- 1 Full HDMI 2.0 – 4K (3840x2160) @ 60 hz
- 1 DisplayPort 1.2 – 4K (4096x2160) @ 60 hz
- eDP display
- 64 GB HS400 eMMC
- i7-8665UE/i5-8365UE:1x GbLAN (i210AT), 1x GbLAN (i219LM)
- i3-8145UE/Celeron-4305UE:1x GbLAN (i210AT), 1x GbLAN (i219V)
- 4 USB 3.0 host ports (USB3.0 Type A socket)
- 1 USB 2.0 host ports (10-pin header) (from HUB)
- Full-size SATA3 port (SATA 6Gb/s)
- ALC887 for Audio Out/Mic In via combo jack
- 1 mini-PCIe+USB/mSATA slot
- mini PCI-e slot supports PCIe Gen.3
- mSATA mode is currently supported through a configuration option from the BIOS menu
- 1 M2 2280 slot B/M-key (M.2 slot supports PCIe Gen.3)
- 1 M2 2230 slot E-key (M.2 slot supports PCIe Gen.3)
The UP Squared has three connectors for GPIO/peripherals:
- m10 header
- HAT connector: pin-compatible with Raspberry Pi Pin position
- MCU connector: extra GPIO/peripheral from the integrated STM32F103C8 MCU
The M10 header has one UART (max 3Mbaud) and one USB 2.0 port available through an adapter cable
http://up-shop.org/up-peripherals/110-usb-20-pin-header-cable.html (only one of the two ports of the adapter can work with UP Xtreme)
- 2x Fintech F81801 RS232/422/485
- 12V, GND
- 3xPCIe x1
- 2x PCIe x1 or USB3.0
- 2xUSB2.0
Each of the HAT pins has a dual function, a standard GPIO in/out mode, and a function mode.
On the board start, all the pin are set in function mode by default but that can be changed within the bios menu see 40-pin multi-function I/O header
- 28 GPIO-capable pins
- 2 I2C ports:
- mode supported Standard, Fast, Fast Plus, High Speed)
- SPI0:
- max speed 25MHZ
- 2 Chip enable *supported modes 0 and 2
- SPI1:
- max speed 25MHZ
- 3 Chip enable
- supported modes 0 and 2
- UART1
- max baud rate 3Mbaud
- hardware flow control
- 3 PWM output (not currently supported due to limitation on Intel PWM driver for WHL-U SoC)
- 1 i2s port (not currently supported due to lack of I2S drivers from Intel for WHL-U SoC)
Programmable I/O managed by an STM32F103C8 MCU.
- 40 pin with 3.3V, 5V, GND, programming pins (for STLink Programmer) and multifunction I/O (GPIO, PWM, I2C, ADC, CAN, I2S, UART, SPI)
- Present
Intel® MAX® 5 CPLD
- 120 mm × 122.0 mm
- 13-60V wide range with lockable connector, validated PSU: [https://up-shop.org/up-peripherals/351-up-xtreme-power-supply.html 19VDC @3.42A 5.5/2.5 mm jack]
