Skip to content
Permalink
Branch: master
Commits on Jul 2, 2019
  1. samples: bluetooth: peripheral_ht: Health Thermometer sample

    overheat authored and jhedberg committed Jun 4, 2019
    Adding Health Thermometer Service sample. Refer to Health Thermometer
    Profile Specification for detailed information about the Health
    Thermometer Profile.
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Commits on May 27, 2019
  1. samples: servo_motor: add HW PWM choice for NRF52 family

    overheat authored and nashif committed Mar 22, 2019
    Hardware PWM make sense for servo control even in a sample,  add HW PWM
    choice for NRF52 family, which support it.
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Commits on May 13, 2019
  1. samples: sensor: bme280: add arduino_101_sss.overlay

    overheat authored and MaureenHelm committed Apr 15, 2019
    Add an overlay file, build out of the box for arduino_101 board.
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
  2. samples: sensor: bme280: add README.rst

    overheat authored and MaureenHelm committed Mar 27, 2019
    Added BME280 (humidity and pressure sensor) sample documentation for
    guiding beginners.
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Commits on May 3, 2019
  1. samples: shields: x_nucleo_iks01a1

    overheat authored and nashif committed Feb 28, 2019
    Fix "arduino_i2c not found" issue, similar to #13708
    Add arduino interfaces in dts to board nrf52_10040
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
  2. samples: bluetooth: ibeacon: change to ADV_NONCONN_IND type

    overheat authored and jhedberg committed May 3, 2019
    According to the Apple iBeacon spec chapter "2.1 Advertising Packet",
    "beacons must use a non connectable undirected Advertising PDU,
    ADV_NONCONN_IND". Refer to https://developer.apple.com/ibeacon/
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Commits on Apr 18, 2019
  1. doc: sample: mpu Update documentation

    overheat authored and nashif committed Apr 10, 2019
    Update documentation to new shell commands.
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Commits on Apr 10, 2019
  1. samples: subsys: logging Remove repetitive code.

    overheat authored and carlescufi committed Apr 9, 2019
    Remove repetitive code
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
  2. doc: subsys: logging Update documentation

    overheat authored and carlescufi committed Apr 9, 2019
    Update documentation.
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Commits on Mar 28, 2019
  1. tests: watchdog: Debug for boards enabled TEST_WDT_CALLBACK_2

    overheat authored and galak committed Mar 13, 2019
    The original code cannot go to the next step on those boards enabled
    TEST_WDT_CALLBACK_2 macro, because of the flow control issue. So the
    test function cannot finish, and the board keeps restart. As a result,
    failure on the test.
    
    Fixes #13468
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
  2. samples: sensor: fix hardware fault when no sensor connected

    overheat authored and galak committed Mar 27, 2019
    There are two sensor samples be modified for a more explicit log when
    no sensor connected or not connected correctly. Rather than a horrible
    hardware fault, which may misleading beginner.
    
    1. bme280
    2. sx9500
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
  3. boards: nucleo_f746zg: Remove repetitive yaml line

    overheat authored and nashif committed Mar 28, 2019
    repetitive line
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Commits on Mar 26, 2019
  1. samples: basic: disco_led without gpio driver

    overheat authored and galak committed Mar 19, 2019
    This sample did not enable gpio driver, so nothing happens after flash
    firmware into a board.
    By enabling gpio driver to fix it.
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Commits on Mar 4, 2019
  1. samples: threads: Fix ASSERTION FAIL without gpio driver

    overheat authored and nashif committed Feb 22, 2019
    Some boards' configuration does not enable GPIO by default,
    like nrf52_pca10056, it causes ASSERTION FAIL when running
    this application. This fix is to enable GPIO by default for
    the basic threads sample, like basic blinky sample does.
    
    Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
You can’t perform that action at this time.