Problems with IGR and mode switch using 8bitdo m30 wireless 2.4 gamepad

[orabeidm]

I installed this mod today and found that it only works through the reset button on the console and does not work with the gamepad 8bitdo m30 wireless 2.4.
2 more people from the official telegram forum of this project faced this problem (nicknames in telegram @fanaras @TurBoss and me @DzmitryArabei)
Can this be fixed in the project's readpad.S file or something else?

Please help!

[SukkoPera]

Unfortunately I don't have that controller. Unless someone can lend me one or can take some measurements with a scope or logic analyzer I cannot really do anything about it.

Also please note that chat is no longer a support channel for any of my projects, I shall remove any mentions of it.

[orabeidm]

what measurements do you need to take? I can do it myself or ask my friend who has the appropriate equipment and knowledge.

[SukkoPera]

I need about a capture of a few seconds of at least pins 1, 6 and 9 of the controller port while a 3-button game is running and buttons UP, B, C, A and Start are being pressed and released one at a time.

The capture should be analog and include voltage levels. Ideally, it should be done with a Saleae Logic analyzer as I'm pretty familiar with it, but other solutions could work.

[orabeidm]

I can buy the cheapest Chinese analyzer clone and try to record from these 3 pins. (there 8 channels supported) and send to you. The quality of the recording will most likely not be very high, but I hope this helps.

[SukkoPera]

I'm not sure the cheapest analyzer would also capture analog data, so I'm not sure it would help.

[orabeidm]

when a wired pad is connected, 0.5v appears on pin 9 of the connector, when C is pressed it drops to 0.25, when b is pressed, to zero, if 8 bitdos are connected, then 0.35v, and when C is pressed it drops to 0.08

on pin 6 when connecting 8bitdo is also 0.35v, when you press B it drops to zero

[SukkoPera]

Those values do not make any sense. Those signals are constantly changing, they cannot be measured with a multimeter. That's why I said a scope or a LA is needed.

[orabeidm]

.

yup

[orabeidm]

bought a copy of the saleae logic analyzer. it is determined by the computer under win 11 and also works in the official program of the latest version. Tomorrow I'll try to solder the analyzer outputs on the console and record the keystroke logs. I will do it for the first time.

[orabeidm]

I am the dumbest person in the world!!!
the picture of the installation in the wiki shows port 2 with digit numbers. not board port1 for md2. I soldered the mod late at night and soldered it according to the picture to port 2, while according to the instructions it was necessary to solder according to the instructions to port 1! you need to take a photo of the board from below for the wiki to install the mod in md2. I will also say that this mod is not very useful for users of microsd cartridges from KRIKzz, because the main menu of the cartridge is accessed by pressing the power button off / on. when you press the reset key, only the game is already sewn into the cartridge to be restarted. if it is possible to expand the functionality of the mod with the implementation of on / off with the gamepad, it would be much more useful for all users of the flashcart.ё

[SukkoPera]

You see, this is one of the problems with giving support for this project: you can't even count on the correctness of the installation.

Adding a console on/off feature is far from trivial and it would be a very invasive modification for the console.

Anyway, if you think the documentation or code can be improved or extended with new features, pull requests are welcome :).

Enjoy!

[orabeidm]

oh. I'm not a programmer and I'm not good at github, I don't know how to create a pull request. just keep in mind that the on/off functionality is preferable to the reset functionality. no matter what segaboard changes requires) пн, 29 авг. 2022 г. в 10:13, Giorgioggì ***@***.***>:

…

You see, this is one of the problems with giving support for this project: you can't even count on the correctness of the installation. Adding a console on/off feature is far from trivial and it would be a very invasive modification for the console. Anyway, if you think the documentation or code can be improved or extended with new features, pull requests are welcome :). Enjoy! — Reply to this email directly, view it on GitHub <#27 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AOKKNMRMHCWQ35ULPDHFSDTV3RPKRANCNFSM57Q5FXUA> . You are receiving this because you modified the open/close state.Message ID: ***@***.***>

[orabeidm]

In addition to the fact that there is a bug with the 8 bitdo gamepad that did not go away (I will try to write logs for you), my friend found 1 more bug. in your mod, the RX0 pin is connected to the gamepad pin on which the START and C buttons are simultaneously. because of this there is a confusion in management. he also wrote his own mod with repinning and other changes like automatic polling of gamepad pins, but the problems with the gamepad from 8bitdo have not gone away. also revealed the problem of code execution on Chinese copies of arduino LGT8F328P