The Sensor Watch

The Sensor Watch is a board replacement for the classic Casio F-91W wristwatch. It is powered by a Microchip SAM L22 microcontroller with built-in segment LCD controller. You can write your own programs for the watch using the provided watch library, program the watch over USB using the built-in UF2 bootloader, and then install the board in your existing watch case to run your own software on your wrist.

Features:

ARM Cortex M0+ microcontroller
32KHz crystal for real-time clock with alarm function
Ten digit segment LCD, plus five indicator segments
Three interrupt capable buttons
Red / green PWM’able LED backlight
Optional piezo buzzer (requires some light soldering)
On-board USB Micro B connector
Reset button with double-tap UF2 bootloader
Nine-pin flex PCB connector

You may have noticed that there are no sensors on this board. That is by design: rather than pick sensors for you, the goal is to add a tiny flexible PCB with the sensors YOU want, and interface them over the nine-pin connector. The connector provides the following options for power and connectivity:

3V power (nominal voltage from a CR2016 coin cell, can drop to ~2.7V)
An I²C interface with built-in pull-up resistors
Five general purpose IO pins, which can be configured as:
- Five analog inputs
- Five interrupt-capable digital inputs, with internal pull-up or pull-down resistors
- Five digital outputs
- SPI controller (with one spare analog / GPIO pin leftover)
- One UART TX/RX pair (with three GPIO leftover)
- Up to four PWM pins on two independent TC instances
- Two external wake inputs that can wake from the ultra-low-power BACKUP mode

Pin	Digital	Interrupt	Analog	I2C	SPI	UART	PWM	Ext. Wake
A0	PB04	EIC/EXTINT[4]	ADC/AIN[12]	—	—	—	—	—
SCL	—	—	—	SCL SERCOM1[1]	—	—	—	—
SDA	—	—	—	SDA SERCOM1[0]	—	—	—	—
A1	PB01	EIC/EXTINT[1]	ADC/AIN[9]	—	SCK SERCOM3[3]	RX SERCOM3[3]	TC3[1]	—
A2	PB02	EIC/EXTINT[2]	ADC/AIN[10]	—	MOSI SERCOM3[0]	TX or RX SERCOM3[0]	TC2[0]	RTC/IN[1]
A3	PB03	EIC/EXTINT[3]	ADC/AIN[11]	—	CS SERCOM3[1]	RX SERCOM3[1]	TC2[1]	—
A4	PB00	EIC/EXTINT[0]	ADC/AIN[8]	—	MISO SERCOM3[2]	TX or RX SERCOM3[2]	TC3[0]	RTC/IN[0]

These tiny “sensor boards” have a set outline, and the available area for your electronics is quite small (5.7 × 5.7 × 1 mm). Still, this is plenty of room for an environmental sensor, MEMS accelerometer or magnetometer and a couple of decoupling capacitors. Note that you will likely be limited to QFN and LGA type parts; SOICs are too large, and even SSOP packages are generally too thick. You can find reference designs for several sensor boards in the PCB/Sensor Boards directory within this repository.

Getting code on the watch

The watch library in this repository is very work-in-progress, but it should allow you to get started. To create a new project, copy the “starter-project” folder in the apps folder, and write your code in the app.c file.

You will need to install the GNU Arm Embedded Toolchain to build projects for the watch. The watch library has been tested with the 9-2019-q4-major version and the 10.3-2021.07 versions. If you're using Debian or Ubuntu, it should be sufficient to apt install gcc-arm-none-eabi.

To build your project, open your terminal and navigate to the project's make folder, then type make.

To install the project onto your Sensor Watch board, plug the watch into your USB port and double tap the tiny Reset button on the back of the board. You should see the LED light up red and begin pulsing. (If it does not, make sure you didn’t plug the board in upside down). Once you see the “WATCHBOOT” drive appear on your desktop, type make install. This will convert your compiled program to a UF2 file, and copy it over to the watch.

Using the Movement framework

If you just want to make minor modifications and use existing code, start with the movement directory. You can build the default watch firmware with:

cd movement/make
make

Then copy movement/make/build/watch.uf2 to your watch. If you'd like to modify which faces are built, see movement_config.h.

You may want to test out changes in the emulator first. To do this, you'll need to install emscripten, then run:

cd movement/make
emmake make
python3 -m http.server -d build-sim

Finally, visit watch.html to see your work.

License

Different components of the project are licensed differently, see LICENSE.md.

License

pganguli/Sensor-Watch

ErrorLooks like something went wrong!

About

Resources

License

Uh oh!

Stars

Watchers

Forks

Releases

Packages 0

Languages

Error
Looks like something went wrong!

Packages