rtw88 downstream 🐧

This is a downstream repo with a primary purpose of supporting development, testing and maintenance for the Realtek rtw88 series of WiFi 5 drivers in the Linux kernel.

The most recent addition to this repo is the driver for the RTL8814AU chipset. Testing is needed so if you have an adapter based on the RTL8814AU chipset, please test and report.

Update: There is now also a driver for RTL8814AE PCIe cards, ID 10ec:8813. lspci may call it RTL8813AE, same thing. Please test and report if you still have this card.

🌟 The code in this repo stays in sync with the wireless-next repository, with additional changes to accommodate kernel API changes over time.

📌 Note: The wireless-next repo contains the code set for the next kernel version. If kernel 6.X is out, kernel mainline repo is on 6.X+1-rcY, and wireless-next targets kernel 6.X+2 material.

Compatibility

Compatible with Linux kernel versions 5.4 and newer as long as your distro hasn't modified any kernel APIs. RHEL and all distros based on RHEL will have modified kernel APIs and are unlikely to be compatible with this driver.

Supported Chipsets

PCIe: RTL8723DE, RTL8814AE, RTL8821CE, RTL8822BE, RTL8822CE
SDIO: RTL8723CS, RTL8723DS, RTL8821CS, RTL8822BS, RTL8822CS
USB : RTL8723DU, RTL8811AU, RTL8811CU, RTL8812AU, RTL8812BU, RTL8812CU
USB : RTL8814AU, RTL8821AU, RTL8821CU, RTL8822BU, RTL8822CU

Issues 🚨

Report problems in Issues after you have checked the Q&A at bottom of this README.

⚠️ If you see a line such as:

make[1]: *** /lib/modules/5.17.5-300.fc36.x86_64/build: No such file or directory. Stop.

This indicates you have NOT installed the kernel headers.

Use the following instructions for that step.

Installation Guide

Prerequisites 📋

Below are prerequisites for common Linux distributions before installing this driver.

Ubuntu

sudo apt update && sudo apt upgrade

sudo apt install linux-headers-generic build-essential git

Fedora

sudo dnf update

sudo dnf install kernel-devel git

openSUSE

sudo zypper install make gcc kernel-devel kernel-default-devel git libopenssl-devel

Arch

sudo pacman -Syu

sudo pacman -Sy base-devel git linux-firmware

Remember to install the corresponding kernel headers which is also needed for compilation.

Raspberry Pi OS

sudo apt update && sudo apt upgrade

sudo apt install -y raspberrypi-kernel-headers build-essential git

Installation Using DKMS 🔄

It's highly recommended to install this driver via DKMS especially Secure Boot is enabled on your machine. Using DKMS (Dynamic Kernel Module Support) ensures that the rtw88 kernel modules are automatically rebuilt and re-signed whenever the Linux kernel is updated. Without DKMS, these drivers would stop working after each kernel update, requiring manual re-compilation and re-signing. DKMS should be available through your distribution’s package manager. You can learn more about DKMS here.

Install dkms and all its required dependencies using your preferred package manager.

Clone the rtw88 GitHub repository

git clone https://github.com/lwfinger/rtw88

Build, sign and install the rtw88 driver
```
cd rtw88
```
```
sudo dkms install $PWD
```
Install the firmware necessary for the rtw88 driver
```
sudo make install_fw
```
Enroll the MOK (Machine Owner Key), this is needed ONLY IF Secure Boot is enabled on your machine.
```
sudo mokutil --import /var/lib/dkms/mok.pub
```
For Ubuntu-based distro users, run this command instead
```
sudo mokutil --import /var/lib/shim-signed/mok/MOK.der
```
Note: At this point, you will be requested to enter a password. Remember this password and re-enter it after rebooting your system in order to enroll your new MOK into your system's UEFI. Please see this tutorial for more details.

Installation Using make🛠

You will need to rebuild and reinstall the driver manually after each kernel updates if you choose this way to install the driver. This method is NOT RECOMMENDED for systems with Secure Boot enabled.

git clone https://github.com/lwfinger/rtw88

cd rtw88

make

sudo make install

sudo make install_fw

Installation for Arch-based Distros 🛠

This is the best way for Arch-based distro users to install this driver, one more step is required after running makepkg -si if Secure Boot is enabled on your machine: Enroll the MOK. Please see the step 5 in Installation Using DKMS for details.

git clone https://aur.archlinux.org/rtw88-dkms-git.git

cd rtw88-dkms-git

makepkg -si

Important Information

Below is important information for using this driver.

1. Blacklisting 🚫

A file called rtw88.conf will be installed into /etc/modprobe.d. It will blacklist all in-kernel rtw88 drivers, however, it will not blacklist out-of-kernel vendor drivers. You will need to uninstall any out-of-kernel vendor drivers that you have installed that may conflict.

2. Recovery Problems After Sleep/Hibernation 🛌

Some BIOSs have trouble changing power state from D3hot to D0. If you have this problem, run

sudo cp reload_rtw88.sh /usr/lib/systemd/system-sleep/

That script will unload the driver before sleep or hibernation, and reload it following resumption.

3. How To Load/Unload Kernel Modules (aka Drivers)🪛

The kernel modules for RTL8821CU are used to demonstrate here, you need to change the module name according to the chip that your Wi-Fi adapter uses.

This unloads the modules for RTL8821CU, due to some pecularities in the modprobe utility, two steps are required. If you are not sure the names of the loaded modules for your Wi-Fi adapter, run lsmod | grep -i rtw

sudo modprobe -r rtw_8821cu
sudo modprobe -r rtw_core

# This command will show nothing because the modules for RTL8821CU were unloaded.
lsmod | grep -i rtw

This loads the modules for RTL8821CU, only a single modprobe call is required.

sudo modprobe rtw_8821cu

# This command will show that the modules for RTL8821CU were loaded.
lsmod | grep -i rtw
rtw_8821cu             16384  0
rtw_usb                36864  1 rtw_8821cu
rtw_8821c              98304  1 rtw_8821cu
rtw_core              294912  2 rtw_usb,rtw_8821c
mac80211             1220608  2 rtw_usb,rtw_core
cfg80211             1064960  2 rtw_core,mac80211

4. How To Update The Driver Installed via DKMS

Remove the installed rtw88 drivers completely, please see Q1 in Q&A for details.
Run this command in the rtw88 source directory to pull the latest code
```
git pull
```
Build, sign, install the rtw88 driver from the latest code
```
sudo dkms install $PWD
```

Q&A

Q1: How to remove this driver if it doesn't work as expected?

For users who installed this driver via DKMS, run

sudo dkms remove rtw88/0.6 --all

sudo rm -rf /var/lib/dkms/rtw88

sudo rm -rf /usr/src/rtw88-0.6

sudo rm -f /etc/modprobe.d/rtw88.conf

For users who installed this driver via make, run this command in the rtw88 source directory and then the rtw88 driver will be unloaded and removed.

sudo make uninstall

For Arch-based distro users, run

sudo pacman -Rn rtw88-dkms-git

Q2: My Wi-Fi adapter is plugged in an USB 3 port, how can I keep it in USB 2 mode to avoid potential interference in 2.4 GHz band?

The module rtw_usb has a parameter named switch_usb_mode which can enable or disable USB mode switching, setting it to "n" will keep your adapter in USB 2 mode.

Steps:

Open /etc/modprobe.d/rtw88.conf with your preferred editor.
Change switch_usb_mode=y to switch_usb_mode=n in line 7.
Unplug the Wi-Fi adapter.
Reboot (or unload the rtw88 drivers)
Plug your Wi-Fi adapter back.

Q3: My Wi-Fi adapter still doesn't work after installing this driver and `lsusb` shows it is in CD-ROM mode, what should I do?

Install usb_modeswitch which can switch your adapter from CD-ROM mode to Wi-Fi mode and then your Wi-Fi adapter should be in Wi-Fi mode after reboot.

lwfinger/rtw88

ErrorLooks like something went wrong!

About

Resources

Uh oh!

Stars

Watchers

Forks

Releases

Packages 0

Contributors 43

Languages

Error
Looks like something went wrong!

Packages