markdown-body entry-content container-lg" itemprop="text">

PowerShell Remoting Protocol

PSRP communication is tunneled through the Open Management Infrastructure (OMI) using this OMI provider.

Two parts of PSRP are available - server and client. The client PSRP part (libpsrpclient) is under development, and will be distributed together with PowerShell. The server PSRP package is available now and should be installed after installing OMI as it is an OMI provider.

Get PSRP-Server

You can download and install PSRP-Server from following links:

Platform	Releases	Link
Linux	Debian	psrp-1.4.1-28.universal.x64.deb
Linux	RPM	psrp-1.4.1-28.universal.x64.rpm

Alternatively, you can now also download from Microsoft Repo. Instructions on setting this up can be found here. Follow the instructions for your platform. You can then use your platform's package tool to install OMI (i.e. "sudo apt-get install omi-psrp-server", or "sudo yum install omi-psrp-server").

Package Requirement

Prior to installing PSRP, make sure that OMI and PowerShell are installed.

Development Environment

Toolchain Setup

PSRP has OMI as a submodule so install those dependencies first. Instructions are located in the build-omi README.md.

PSRP requires the following additional dependent packages:

On Ubuntu 14.04 and Ubuntu 16.04

sudo apt-get install cmake

On CentOS 7.x

sudo yum install cmake

Also install PowerShell from the latest release per their instructions.

Git Setup

PSRP has a submodule, so clone recursively.

git clone --recursive https://github.com/PowerShell/psl-omi-provider.git

Building

Run make debug or make release to build OMI and the provider.

In debug mode, this script first builds OMI in developer mode:

pushd omi/Unix
./configure --dev
make -j
popd

Then it builds and registers the provider:

pushd src
cmake -DCMAKE_BUILD_TYPE=Debug .
make -j
popd

In release mode, this script will build omi, the provider, and packages (for distribution).

Running

Connecting from Windows to Linux

Some initial setup on Windows is required. Open an administrative command prompt and execute the following:

winrm set winrm/config/Client @{TrustedHosts="*"}

You can also set the TrustedHosts to include the target's IP address.

Then on Linux, launch omiserver (if you installed OMI from its installation package, omiserver is probably already running):

./run.sh

Now in a PowerShell prompt on Windows (opened after setting the WinRM client configurations):

$cred = Get-Credential
$o = New-PSSessionOption -SkipCACheck -SkipRevocationCheck -SkipCNCheck
Enter-PSSession -ComputerName <IP address of Linux machine> -Credential $cred -Authentication basic -UseSSL -SessionOption $o

The IP address of the Linux machine can be obtained with:

ip -f inet addr show dev eth0

Connecting from Linux to Windows

For Centos 7.3 and later, and Ubuntu 16.04 or later, Powershell supports Secure Protected Negotiated authentication (SPNEGO). This allows the use of NTLM based authentication and encryption of traffic over the http connection. Use of SPNEGO authentication is more secure than basic authentication on http, and less complex than https. Support of NTLM authentication on MacOS is deprecated by apple. We are currently working on Kerberos protocol support which will allow SPNEGO or direct Kerberos authentication on MacOS as well as at least some older Linux distributions.

In order to perform NTLM authentication there must be matching credentials on both ends of the transaction. The necessary setup of the ntlm credentials for both server and client is described in the document setup-ntlm-omi.

Note that the server side will need an additional registry setting to enable administrators, other than the built in administrator, to connect using NTLM. Refer to the LocalAccountTokenFilterPolicy registry setting under Negotiate Authentication in Authentication for Remote Connections

If you are not using SPNEGO authentication, or wish to use basic authentication on http, the WinRM server needs to be configured to allow unencrypted traffic and accept basic authentication for inbound connections. Note that this sends passwords over unencrypted http. We do not recommend it. If the http socket is enabled and basic authentication is allowed, there is currently no way to prevent the use of basic authentication over http, which exposes passwords.

To enable basic auth, on Windows in an administrative command prompt run:

winrm set winrm/config/Service/Auth @{Basic="true"}

Basic authentication has acceptable security over https, but all communications using basic authentication over http are unencrypted. Connections using SPNEGO authentication are encrypted, and have acceptable security.

To enable unencrypted communication over http on Windows in an administrative command prompt you must also run:

winrm set winrm/config/Service @{AllowUnencrypted="true"}

Basic authentication with WinRM can only access local machine accounts so you will need to create a local account on your Windows machine that is part of the administrator group.a SPNEGO connections can use domain credentials.

Building this repository generates two new binaries that need to be picked up instead of the ones included by PowerShell for Linux itself. Run PowerShell as:

export LD_LIBRARY_PATH=psl-omi-provider-path/src:psl-omi-provider-path/omi/Unix/output/lib:${LD_LIBRARY_PATH} && powershell

where psl-omi-provider-path is where you enlisted your psl-omi-provider code.

Now in PowerShell prompt on Linux you can connect to Windows using this command:

$cred = Get-Credential
Enter-PSSession -ComputerName <IP address of windows machine> -Credential $cred -Authentication basic

License

PowerShell/psl-omi-provider

ErrorLooks like something went wrong!

About

Topics

Resources

License

Code of conduct

Security policy

Uh oh!

Stars

Watchers

Forks

Releases 7

Packages 0

Contributors 12

Uh oh!

Languages

Error
Looks like something went wrong!

Packages