RabbitMQ Clusterer

This plugin is no longer maintained, and completely unnecessary with supported releases of RabbitMQ.

This plugin provided an alternative means for creating and maintaining RabbitMQ clusters. It is highly opinionated and was created with specific opinionated infrastructure provisioning tooling in mind. Team RabbitMQ considers it to be a failed experiment and highly recommends against it.

Please upgrade to a supported RabbitMQ version instead. It provides a peer discovery subsystem introduced in RabbitMQ 3.7.0 or its predecessor, rabbitmq-autocluster. That plugin is not a strict alternative to this one but targets a wider range of provisioning scenarios.

Project status

The plugin was created to handle arbitrary order on nodes restart. Since RabbitMQ version 3.6.7 this problem is addressed in the core.

This plugin is considered deprecated, and it's recommended to switch to RabbitMQ's built-in cluster formation feature in order to avoid known issues that this plugin's opinionated behavior entails (such as #7).

Overview

Traditional RabbitMQ clustering is not very friendly to infrastructure automation tools such as Chef, Puppet or BOSH. The existing tooling (rabbitmqctl join_cluster and friends) is imperative, requires more oversight and does not handle potentially random node boot order very well. The Clusterer has been specifically designed with automated deployment tools in mind.

Unlike the existing tooling, the Clusterer is declarative and goal directed: you tell it the overall shape of the cluster you want to construct and the clusterer tries to achieve that. With the Clusterer, cluster configuration can be provided in a single location (a configuration file).

With rabbitmq-clusterer, nodes in a cluster can be restarted in any order, which can be the case with automation tools performing upgrades/reconfiguration, or due to node failure timing.

Project Maturity

This plugin is ancient abandonware. Do not use. Yes, really, it no longer has any reasons to exist.

Compatibility With Traditional RabbitMQ Clustering

The Clusterer is not generally compatible with the existing clustering tool-set. Do not use any of the rabbitmqctl commands relating to changing clusters: join_cluster, change_cluster_node_type, and update_cluster_nodes must not be used. If you do use these, this plugin likely won't be able to perform its jobs.

rabbitmqctl cluster_status may be used to inspect a cluster state, but the Clusterer sends to the standard Rabbit log files details about any clusters it joins or leaves. See the Inspecting the Clusterer Status section further down.

rabbitmqctl stop_app, rabbitmqctl forget_cluster_node, and rabbitmqctl start_app can be used to force a node out of a cluster before cluster config can be changed. While this is not generally recommended, there can be valid reasons for doing so, e.g. node running out of disk space and/or needing replacement for other reasons.

cluster_nodes in the RabbitMQ config file is incompatible with this plugin and must not be used.

Installation

Binary builds of this plugin are available from

Bintray (like with other RabbitMQ Community Plugins)
GitHub releases page

As with all other plugins, you must put the plugin archive (.ez) in the RabbitMQ plugins directory and enable it with rabbitmq-plugins enable rabbitmq_clusterer --offline.

For Recent RabbitMQ Versions (3.5.4 and Later)

Compiled plugin file needs to be placed into .

To use the plugin, it is necessary to override RABBITMQ_BOOT_MODULE to rabbit_clusterer. This is done similarly to other RabbitMQ environment variables.

Because this plugin coordinates RabbitMQ node start, it needs to be manually added to the Erlang VM code path:

export RABBITMQ_BOOT_MODULE=rabbit_clusterer
export RABBITMQ_SERVER_ADDITIONAL_ERL_ARGS="-pa /path/to/rabbitmq/plugins/rabbitmq_clusterer.ez/rabbitmq_clusterer-{clusterer-version}/ebin"

where {clusterer-version} is the build of the plugin (see GitHub releases page and Bintray):

export RABBITMQ_BOOT_MODULE=rabbit_clusterer
export RABBITMQ_SERVER_ADDITIONAL_ERL_ARGS="-pa /path/to/rabbitmq/plugins/rabbitmq_clusterer-1.0.3.ez/rabbitmq_clusterer-1.0.3/ebin"

Since .ez files are .zip archives, they can be easily inspected when you are not sure about the exact name of the directory you the file you've downloaded.

For RabbitMQ 3.4.x

rabbitmq-server Patch

With RabbitMQ versions earlier than 3.5.4, it is necessary to apply a rabbitmq-server patch and re-compile the broker.

The patch is provided in rabbitmq-clusterer/rabbitmq-server.patch. Change into the server scripts directory and apply it with:

patch -p1 < rabbitmq-clusterer/rabbitmq-server.patch

The patch assumes the plugin archive is at ${RABBITMQ_PLUGINS_DIR}/rabbitmq_clusterer.ez.

Usage in Environments with Dynamic Hostnames (e.g. Kubernetes)

Since this plugin assumes that all cluster members are known ahead of time and listed in the config, environments with dynamically generated hostnames must be configured to use known (or completely predictable) hostnames.

For Kubernetes specifically, there's an example repository contributed by Matt Friendman.

There's also another example that uses Kubernetes 1.5.x.

Cluster Config Specification

The Clusterer will communicate a new valid config to both all the nodes of its current config, and in addition to all the nodes in the new config. Even if the cluster is able to be formed in the absence of some nodes indicated in the config, the nodes of the cluster will continue to attempt to make contact with any missing nodes and will pass the config to them if and when they eventually appear.

All of which means that you generally only need to supply new configs to a single node of any cluster. There is no harm in doing more than this. The Clusterer stores on disk the currently applied config (it stores this next to the mnesia directory Rabbit uses for all its persistent data) and so if a node goes down, it will have a record of the config in operation when it was last up. When it comes back up, it will attempt to rejoin that cluster, regardless of whether this node was ever explicitly given this config.

There are a couple of ways to specify a cluster config: via an external file or inline.

Using External Config File

In a rabbitmq_clusterer section in rabbitmq.config file you can add a config entry that is a path to configuration file.

Below are some examples.

When using rabbitmq.conf (currently only available in RabbitMQ master):

clusterer.config = /path/to/my/cluster.config

When using the classic configuration format (rabbitmq.config, prior to 3.7.0) or advanced.config:

  [{rabbitmq_clusterer,
      [{config, "/path/to/my/cluster.config"}]
   }].

Like with rabbitmq.config or any other Erlang terms file, the dot at the end is mandatory.

Using Inline Configuration in rabbitmq.config

It is possible to provide cluster configuration in rabbitmq.config.

In rabbitmq.conf:

clusterer.version = 43
clusterer.nodes.disc.1 = rabbit@hostA
clusterer.nodes.disc.2 = rabbit@hostD
clusterer.nodes.ram.1  = rabbit@hostB
clusterer.gospel.node = rabbit@hostD

Or, using the classic config format (rabbitmq.config, prior to 3.7.0) or advanced.config:

  [{rabbitmq_clusterer,
      [{config,
          [{version, 43},
           {nodes, [{rabbit@hostA, disc}, {rabbit@hostB, ram}, {rabbit@hostD, disc}]},
           {gospel, {node, rabbit@hostD}}]
       }]
   }].

This approach makes configuration management with tools such as Chef somewhat less convenient, so external configuration file is the recommended option.

Using rabbitmqctl eval

rabbitmqctl eval 'rabbit_clusterer:apply_config().'

This will only have any effect if there is an entry in the rabbitmq.config file for the Clusterer as above, and a path is specified as the value rather than a config directly.

If that is the case, then this will cause the node to reload the file containing cluster config and apply it. Note that you cannot change the path itself in the rabbitmq.config file dynamically: neither Rabbit nor the Clusterer will pick up any changes to that file without restarting the whole Erlang node.

rabbitmqctl eval 'rabbit_clusterer:apply_config("/path/to/my/other/cluster.config").'

This will cause the Clusterer to attempt to load the indicated file as a cluster config and apply it. Using this method rather than the above allows the path to change dynamically and does not depend on any entries in the rabbitmq.config file. The path provided here is not retained in any way: providing the path here does not influence future calls to rabbit_clusterer:apply_config(). - using rabbit_clusterer:apply_config(). always attempts to inspect the path as found in rabbitmq.config when the node was started.

Note if you really want to, rather than suppling a path to a file, you can supply the cluster config as a proplist directly, just as you can in the rabbitmq.config file itself.

Cluster Configuration

A cluster config is an Erlang proplist consisting of just four tuples. The config can be supplied to Rabbit in a variety of ways and it is in general only necessary to supply a config to a single node of a cluster: the Clusterer will take care of distributing the config to all the other nodes as necessary.

[{version, 43},
 {nodes, [{rabbit@hostA, disc}, {rabbit@hostB, ram}, {rabbit@hostD, disc}]},
 {gospel, {node, rabbit@hostD}}].

The above gives an example cluster config. This specifies that the cluster is formed out of the nodes rabbit@hostA, rabbit@hostB and rabbit@hostD and that rabbit@hostA and rabbit@hostD are disc nodes and rabbit@hostB is a ram node. The nodes tuple is really the only tuple that describes the shape of the cluster. The other tuples describe how to achieve the cluster, and are thus mainly irrelevant once the cluster has been achieved.

In general, the Clusterer will wait indefinitely for the conditions to be correct to form any given cluster. This is in contrast to the existing tools which will either timeout or in some cases take (arguably) unsafe actions. For example, the existing tools will allow a fresh node to fully start when it is supplied with a cluster configuration which involves other nodes which are not currently contactable. This is unsafe because those other nodes might not be fresh nodes: the intention would be for the fresh node to sync with those other nodes and preserve the data those nodes hold. When those other nodes eventually return, manual intervention is then required to throw away some data and preserve others. The Clusterer, by contrast, would wait until it could either verify that all the nodes to be part of the cluster are fresh (so there is no data to preserve at all), or failing that would wait until one of the non-fresh nodes was fully up and running, at which point it could sync with that node.

version: non negative integer

All configs are versioned and this is used to decide which of any two configs is the youngest. A config which has a smaller version number is older. Configs will be ignored unless they are younger than the current config. Note that in lieu of any config being provided by the user, the default config is used which has a version of 0. Thus user supplied configs should use a version of 1 or greater.
nodes: list

List the names of the nodes that are to be in the cluster. If you list node names directly then they are considered to be disc nodes. If you specify nodes by using a tuple, you can specify a disc node using either disc or disk. If you want to specify ram nodes, you must use a tuple, with ram as the second element. Order of nodes does not matter. The following are all equivalent.
```
  {nodes, [rabbit@hostA, rabbit@hostD, {rabbit@hostB, ram}]}
  {nodes, [rabbit@hostD, rabbit@hostA, {rabbit@hostB, ram}]}
  {nodes, [{rabbit@hostB, ram}, rabbit@hostD, rabbit@hostA]}
  {nodes, [rabbit@hostA, {rabbit@hostD, disk}, {rabbit@hostB, ram}]}
  {nodes, [{rabbit@hostA, disc}, {rabbit@hostD, disk}, {rabbit@hostB, ram}]}
```
gospel: reset or {node, nodename}

When multiple nodes are to become a cluster (or indeed multiple clusters are to merge: you can think of an unclustered node as a cluster of a single node) some data must be lost and some data can be preserved: given two unclustered nodes A and B that are to become a cluster, either A's data can survive or Bs data can survive, or neither, but not both. The gospel` tuple allows you to specify which data should survive:
- reset will reset all nodes in the cluster. This will apply every time the cluster config is changed and applied (i.e. if you change some other setting in the config, bump the version number, leave the gospel as reset and apply the config to any node in your cluster, you will find the entire cluster resets). This is deliberate: it allows you to very easily and quickly reset an entire cluster, but in general you'll only occasionally want to set gospel to reset.
- {node, nodename} The nodename must appear in the nodes tuple. The data held by the existing cluster of which nodename is a member will survive. Nodes that are listed in the nodes tuple but which are not currently members of the same cluster as nodename will be reset. The phrasing here is very deliberate: it is not necessary for nodename to actually be up and running for this to work. If you have an existing cluster of nodes A and B and you want to add in node C you can set the gospel to be {node, A}, add C to the nodes tuple, bump the version and apply the config to C and provided at least one of A or B is up and running, C will successfully cluster. I.e. if only B is up, B still knows that it is clustered with A, it just happens to be the case that A is currently unavailable. Thus C can cluster with B and both will happily work, awaiting the return of A.
  
  In this particular case, the subsequent behaviour when A returns is important. If A has been reset and is now running an older config then it is A that is reset again to join back in with B and C. I.e. the gospel setting is really identifying that the data that A holds at a particular moment in time is the data to be preserved. When A comes back, having been reset, A realises that the gospel is indicating an older version of A, which is preserved by the surviving cluster nodes of B and C, not the newer reset data held by A. The upshot of this is that in your cluster, if a node fails, goes down and has to be reset, then to join it back into the cluster you don't need to alter anything in the cluster config (and indeed shouldn't): even if the failed node was named as the gospel, you shouldn't make any changes to the config.
  
  By contrast, if A comes back and has been reset but is now running a younger config than B and C, then that younger config will propagate to B and C. If A is named as the gospel in the new younger config, then that refers to the data held by the new younger A, and so B and C will reset as necessary.

Mistakes in config files

Config files can contain mistakes. If you apply a config file using rabbitmqctl eval then you'll get feedback directly. If you specify the config file via rabbitmq.config then and mistakes will be logged to Rabbit's log files.

In general, the Clusterer tries reasonably hard to give informative messages about what it doesn't like, but that can only occur if the config is syntactically valid in the first place. If you forget to bump the version number it will complain, and generally whenever the Clusterer comes across configs with equal version numbers but semantically different contents it takes highly evasive action: in some situations, it may decide to shut down the whole Erlang node immediately. It is your responsibility to manage the version numbers: the Clusterer expects to be able to order configs by version numbers, and thus determine the youngest config. You need to ensure it can do this. If you're building cluster configs automatically, one sensible approach would be to set the version to the number of seconds since epoch, for example.

Inspecting the Clusterer Status

rabbitmqctl cluster_status presents basic information about clusters, but does not interact with the Clusterer. rabbitmqctl eval 'rabbit_clusterer:status().', on the other hand, does, and shows which config is in operation by the node and what the Clusterer is trying to do. If the cluster has been established then the command will also display which nodes are known to be currently up and running.

Building From Source

The Clusterer reuses parts of the RabbitMQ umbrella repository. Before building the plugin, make sure it is cloned as rabbitmq_clusterer under it, much like other plugins.

To build the plugin run make. The VERSION environment variable is used to specify plugin version, e.g.:

VERSION=3.6.6 make

To package the plugin run make dist. In some cases, make clean dist is the safest option.

Linking in Development Environment

If you're running a development environment and want to link through from the rabbit/plugins directory, link to rabbitmq_clusterer/plugins/rabbitmq_clusterer-$VERSION.ez. Do not just link to the rabbitmq_clusterer directory.

License and Copyright

(c) 2013-2017 Pivotal Software Inc.

License

rabbitmq/rabbitmq-clusterer

ErrorLooks like something went wrong!

About

Topics

Resources

License

Code of conduct

Security policy

Uh oh!

Stars

Watchers

Forks

Releases 3

Packages 0

Contributors 9

Uh oh!

Languages

Error
Looks like something went wrong!

Packages