example.ino

/*
 * Copyright (C) 2017 Robert Bosch. All Rights Reserved. 
 *
 * Disclaimer
 *
 * Common:
 * Bosch Sensortec products are developed for the consumer goods industry. They may only be used
 * within the parameters of the respective valid product data sheet.  Bosch Sensortec products are
 * provided with the express understanding that there is no warranty of fitness for a particular purpose.
 * They are not fit for use in life-sustaining, safety or security sensitive systems or any system or device
 * that may lead to bodily harm or property damage if the system or device malfunctions. In addition,
 * Bosch Sensortec products are not fit for use in products which interact with motor vehicle systems.
 * The resale and/or use of products are at the purchasers own risk and his own responsibility. The
 * examination of fitness for the intended use is the sole responsibility of the Purchaser.
 *
 * The purchaser shall indemnify Bosch Sensortec from all third party claims, including any claims for
 * incidental, or consequential damages, arising from any product use not covered by the parameters of
 * the respective valid product data sheet or not approved by Bosch Sensortec and reimburse Bosch
 * Sensortec for all costs in connection with such claims.
 *
 * The purchaser must monitor the market for the purchased products, particularly with regard to
 * product safety and inform Bosch Sensortec without delay of all security relevant incidents.
 *
 * Engineering Samples are marked with an asterisk (*) or (e). Samples may vary from the valid
 * technical specifications of the product series. They are therefore not intended or fit for resale to third
 * parties or for use in end products. Their sole purpose is internal client testing. The testing of an
 * engineering sample may in no way replace the testing of a product series. Bosch Sensortec
 * assumes no liability for the use of engineering samples. By accepting the engineering samples, the
 * Purchaser agrees to indemnify Bosch Sensortec from all claims arising from the use of engineering
 * samples.
 *
 * Special:
 * This software module (hereinafter called "Software") and any information on application-sheets
 * (hereinafter called "Information") is provided free of charge for the sole purpose to support your
 * application work. The Software and Information is subject to the following terms and conditions:
 *
 * The Software is specifically designed for the exclusive use for Bosch Sensortec products by
 * personnel who have special experience and training. Do not use this Software if you do not have the
 * proper experience or training.
 *
 * This Software package is provided `` as is `` and without any expressed or implied warranties,
 * including without limitation, the implied warranties of merchantability and fitness for a particular
 * purpose.
 *
 * Bosch Sensortec and their representatives and agents deny any liability for the functional impairment
 * of this Software in terms of fitness, performance and safety. Bosch Sensortec and their
 * representatives and agents shall not be liable for any direct or indirect damages or injury, except as
 * otherwise stipulated in mandatory applicable law.
 *
 * The Information provided is believed to be accurate and reliable. Bosch Sensortec assumes no
 * responsibility for the consequences of use of such Information nor for any infringement of patents or
 * other rights of third parties which may result from its use. No license is granted by implication or
 * otherwise under any patent or patent rights of Bosch. Specifications mentioned in the Information are
 * subject to change without notice.
 *
 * It is not allowed to deliver the source code of the Software to any third party without permission of
 * Bosch Sensortec.
 *
 */

/*!
 * @file bsec_iot_example.ino
 *
 * @brief
 * Example for using of BSEC library in a fixed configuration with the BME680 sensor.
 * This works by running an endless loop in the bsec_iot_loop() function.
 */

/*!
 * @addtogroup bsec_examples BSEC Examples
 * @brief BSEC usage examples
 * @{*/

/**********************************************************************************************************************/
/* header files */
/**********************************************************************************************************************/

#include "bsec_integration.h"
#include <Wire.h>
#include <ESP8266WiFi.h>
#include <SoftwareSerial.h>
#include <WiFiUDP.h>

//Settings needet for serial communication with MH-Z14A
SoftwareSerial SerialCom (0,2); //D3, D4
byte addArray[] = {0xFF, 0x01, 0x86, 0x00, 0x00, 0x00, 0x00, 0x00, 0x79};
char dataValue[9];
String dataString = "";

//WiFi Settings
const char* ssid = "Your SSID";
const char* password = "Your PW";

// the IP address of your InfluxDB host
byte host[] = {1, 1, 1, 1};

// the port that the InfluxDB UDP plugin is listening on
int port = 8089;

WiFiUDP udp;
							 								  											
/**********************************************************************************************************************/
/* functions */
/**********************************************************************************************************************/

/*!
 * @brief           Write operation in either Wire or SPI
 *
 * param[in]        dev_addr        Wire or SPI device address
 * param[in]        reg_addr        register address
 * param[in]        reg_data_ptr    pointer to the data to be written
 * param[in]        data_len        number of bytes to be written
 *
 * @return          result of the bus communication function
 */
int8_t bus_write(uint8_t dev_addr, uint8_t reg_addr, uint8_t *reg_data_ptr, uint16_t data_len)
{
    Wire.beginTransmission(dev_addr);
    Wire.write(reg_addr);    /* Set register address to start writing to */
 
    /* Write the data */
    for (int index = 0; index < data_len; index++) {
        Wire.write(reg_data_ptr[index]);
    }
 
    return (int8_t)Wire.endTransmission();
}

/*!
 * @brief           Read operation in either Wire or SPI
 *
 * param[in]        dev_addr        Wire or SPI device address
 * param[in]        reg_addr        register address
 * param[out]       reg_data_ptr    pointer to the memory to be used to store the read data
 * param[in]        data_len        number of bytes to be read
 *
 * @return          result of the bus communication function
 */
int8_t bus_read(uint8_t dev_addr, uint8_t reg_addr, uint8_t *reg_data_ptr, uint16_t data_len)
{
    int8_t comResult = 0;
    Wire.beginTransmission(dev_addr);
    Wire.write(reg_addr);                    /* Set register address to start reading from */
    comResult = Wire.endTransmission();
 
    delayMicroseconds(150);                 /* Precautionary response delay */
    Wire.requestFrom(dev_addr, (uint8_t)data_len);    /* Request data */
 
    int index = 0;
    while (Wire.available())  /* The slave device may send less than requested (burst read) */
    {
        reg_data_ptr[index] = Wire.read();
        index++;
    }
 
    return comResult;
}

/*!
 * @brief           System specific implementation of sleep function
 *
 * @param[in]       t_ms    time in milliseconds
 *
 * @return          none
 */
void sleep(uint32_t t_ms)
{
    delay(t_ms);
}

/*!
 * @brief           Capture the system time in microseconds
 *
 * @return          system_current_time    current system timestamp in microseconds
 */
int64_t get_timestamp_us()
{
    return (int64_t) millis() * 1000;
}

/*!
 * @brief           Handling of the ready outputs
 *
 * @param[in]       timestamp       time in nanoseconds
 * @param[in]       iaq             IAQ signal
 * @param[in]       iaq_accuracy    accuracy of IAQ signal
 * @param[in]       temperature     temperature signal
 * @param[in]       humidity        humidity signal
 * @param[in]       pressure        pressure signal
 * @param[in]       raw_temperature raw temperature signal
 * @param[in]       raw_humidity    raw humidity signal
 * @param[in]       gas             raw gas sensor signal
 * @param[in]       bsec_status     value returned by the bsec_do_steps() call
 *
 * @return          none
 */
void output_ready(int64_t timestamp, float iaq, uint8_t iaq_accuracy, float temperature, float humidity,
     float pressure, float raw_temperature, float raw_humidity, float gas, bsec_library_return_t bsec_status)
{
      Serial.print("[");
      Serial.print(timestamp/1e6);
      Serial.print("] T: ");
      Serial.print(temperature);
      Serial.print("| rH: ");
      Serial.print(humidity);
      Serial.print("| P: ");
      Serial.print(pressure/100);
      Serial.print("| IAQ: ");
      Serial.print(iaq);
      Serial.print(" (");
      Serial.print(iaq_accuracy);
      Serial.println(")");
	  
      SerialCom.write(addArray, 9);
      SerialCom.readBytes(dataValue, 9);
      int resHigh = (int) dataValue[2];
      int resLow  = (int) dataValue[3];
      int pulse = (256*resHigh)+resLow;
      dataString = String(pulse);
      Serial.print("PPM : ");
      Serial.println(pulse);

      String line;
      // concatenate the temperature into the line protocol
      //line = String("arbeit t=" + temperature);
      line += F("arbeit t=");
      line += String(temperature);
      line += F(",h=");
      line += String(humidity);
      line += F(",p=");
      line += String(pressure/100);
      line += F(",iaq=");
      line += String(iaq);
      line += F(",co2=");
      line += String(pulse);
      Serial.println(line);
      
      // send the packet
      Serial.println("Sending UDP packet...");
      udp.beginPacket(host, port);
      udp.print(line);
      udp.endPacket();
	  
}

/*!
 * @brief           Load previous library state from non-volatile memory
 *
 * @param[in,out]   state_buffer    buffer to hold the loaded state string
 * @param[in]       n_buffer        size of the allocated state buffer
 *
 * @return          number of bytes copied to state_buffer
 */
uint32_t state_load(uint8_t *state_buffer, uint32_t n_buffer)
{
    // ...
    // Load a previous library state from non-volatile memory, if available.
    //
    // Return zero if loading was unsuccessful or no state was available, 
    // otherwise return length of loaded state string.
    // ...
    return 0;
}

/*!
 * @brief           Save library state to non-volatile memory
 *
 * @param[in]       state_buffer    buffer holding the state to be stored
 * @param[in]       length          length of the state string to be stored
 *
 * @return          none
 */
void state_save(const uint8_t *state_buffer, uint32_t length)
{
    // ...
    // Save the string some form of non-volatile memory, if possible.
    // ...
}

/*!
 * @brief           Load library config from non-volatile memory
 *
 * @param[in,out]   config_buffer    buffer to hold the loaded state string
 * @param[in]       n_buffer        size of the allocated state buffer
 *
 * @return          number of bytes copied to config_buffer
 */
uint32_t config_load(uint8_t *config_buffer, uint32_t n_buffer)
{
    // ...
    // Load a library config from non-volatile memory, if available.
    //
    // Return zero if loading was unsuccessful or no config was available, 
    // otherwise return length of loaded config string.
    // ...
    return 0;
}

/*!
 * @brief       Main function which configures BSEC library and then reads and processes the data from sensor based
 *              on timer ticks
 *
 * @return      result of the processing
 */
void setup()
{
    return_values_init ret;

    /* Init I2C and serial communication */
    Wire.begin();
    Serial.begin(115200);
	    SerialCom.begin(9600);
  // Connecting to WiFi network
  Serial.println();
  Serial.print("Connecting to ");
  Serial.println(ssid);

  WiFi.begin(ssid, password);
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("");
  Serial.println("WiFi connected");

  // Printing the ESP IP address
  Serial.println(WiFi.localIP());
							   
    /* Call to the function which initializes the BSEC library 
     * Switch on low-power mode and provide no temperature offset */
    ret = bsec_iot_init(BSEC_SAMPLE_RATE_ULP, 0.0f, bus_write, bus_read, sleep, state_load, config_load);
    if (ret.bme680_status)
    {
        /* Could not intialize BME680 */
        Serial.println("Error while initializing BME680");
        return;
    }
    else if (ret.bsec_status)
    {
        /* Could not intialize BSEC library */
        Serial.println("Error while initializing BSEC library");
        return;
    }
    
    /* Call to endless loop function which reads and processes data based on sensor settings */
    /* State is saved every 10.000 samples, which means every 10.000 * 3 secs = 500 minutes  */
    bsec_iot_loop(sleep, get_timestamp_us, output_ready, state_save, 10000);
}

void loop()
{
}

/*! @}*/