Start NiMH Reconditioning doesn't show any update #1215
Comments
|
Hello there! |
|
Hello @limpkin ! |
|
You may bypass the battery check by keeping the "shift" key pressed when
you click the "select update file" button.
Once upgraded, I'm fairly sure the reconditioning should work :)
…On Sun, Mar 3, 2024 at 2:38 PM ConYel ***@***.***> wrote:
Hello @limpkin <https://github.com/limpkin> !
Unfortunately I was trying to update to v13 from v5(I think) but I cannot
as it doesn't allow me to do it if it is not charged first.
Is there any way that I can make the battery work or the device is
"useless"?
—
Reply to this email directly, view it on GitHub
<#1215 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABPCNM2AJC242CAITCPV3GLYWMRUTAVCNFSM6AAAAABED4QAS2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSNZVGE3DONZTGE>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
|
Hi @limpkin and thanks for the prompt reply! I will update here later if the recondition worked!
|
Even after 8 hours it didn't change any state. Any solutions from this point on? |
|
reconditioning procedure not finishing?
I don't think I have a solution... let me check
…On Mon, Mar 4, 2024 at 9:21 AM ConYel ***@***.***> wrote:
Update2
Even after 8 hours it didn't change any state. Any solutions from this
point on?
—
Reply to this email directly, view it on GitHub
<#1215 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABPCNM6IIP2PUORD2YYRAULYWQVJDAVCNFSM6AAAAABED4QAS2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSNZVHE3TONZTGE>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
|
Yeap that is the issue. It doesn't seem to finish ever. |
|
If the battery is dead, how is it possible to replace it? |
|
I'm afraid not without breaking the case.... but some good 3d printed case can be found: https://www.reddit.com/r/mooltipass/comments/191285c/custom_3d_printed_enclosure_for_mooltipass_ble/ |
|
How can I check that the battery is dead? |
|
Does the device switch off after being disconnected?
The most likely reason why the procedure doesn't finish is that the
charging algorithm doesn't seem to be able to reach a certain voltage
during the initial charging phase...
…On Wed, Mar 6, 2024 at 11:34 PM ConYel ***@***.***> wrote:
How can I check the the battery is dead?
Anyway to know why the reconditioning procedure is not finishing?
—
Reply to this email directly, view it on GitHub
<#1215 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABPCNM3HMZ5KQ26RCV7SSA3YW6KYRAVCNFSM6AAAAABED4QAS2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSOBRHE3TAMZYHA>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
|
Yes immediately, but I was able to do update the firmware. |
|
FWIW I've checked the little box that said something along the lines of "continue until original capacity is reached". I'm about 72 hours in. I'm on the latest bundle/moolticute available for the miniBLE as of 72 hours ago. Is there an ideal phase for me to unplug it and halt the processes since there's no progress indicator and I'm giving up on it ending naturally? (rest, discharge, etc) LMK if there's any data I can collect to help out with this. |
|
I'd recommend disconnecting during the charge phase :) |
Expected behavior
I have been trying for more than 12 hours to recondition the battery but it doesn't show any different behavior.
First time I waited for 5 hours.
Then I tried again for another 5 hours.
Then I left it overnight >7 hours.
Still battery doesn't seem to be charged.
Actual behavior
I am not sure what it should show when the battery has been charged.
Could you add some pictures to the guide?
Step by step guide to reproduce the problem
Moolticute Version
custom build v1.03.0
Operating System
Mooltipass Device
The text was updated successfully, but these errors were encountered: