-
Notifications
You must be signed in to change notification settings - Fork 5
/
README.TXT
116 lines (105 loc) · 5.16 KB
/
README.TXT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
TASS Software v0.80 (6 June 2020)
-- Merged in N4MTT's changes from 18 November 2018
with a few tweaks (version number, etc.)
-- Changed optional "double pole" board from D to A as it turns out
that is probably more practical for many applications. Should
make it possible to set any board for that mode...
TASS Software v0.70-n4mtt (18 November 2018)
-- Tested support for using both an Ethernet shield and the touch screen
shield. A version 2 (WIZnet w5500) Ethernet shield is required. The
the earlier Ethernet shield is missing four pins that are needed for
the touch screen shield.
= The Ethernet shield and the touch screen shield both use digital pin
10 as a slave select (SS). I cut the psychical pin for digital pin
10 on the touch screen shield. Then I ran a wire from the PCB pad
for pin 10 to the pad for digital pin 2. Then in changed the
define TFT_CS from 10 to 2.
-- Added support for WIZnet w5500 Ethernet shields to use the Ethernet2
library.
= Enabled with the "USE_W5500" define.
-- Added displaying the current status of the relays to the telnet
server and USB output.
= Enable the "SHOW_INFO_ETHERNET" define for display with the telnet
server.
= Enable the "SHOW_INFO_USB" define for the display with the USB
output.
-- Updated the touch screen display to show the current status of the
relays. When the board field is touched the relay fields display the
status of the relays. The color of the relay number shows the status
the relay.
= Red: The relay is set.
= Orange: The relay is "hold".
-- Added support to not display all four boards on the touch screen and
in the "SHOW_INFO_ETHERNET" and "SHOW_INFO_USB" displays.
-= Set the "NUM_TASS_BOARDS_DISPLAY" to the number of boards to
display.
--= On the touch screen the fields for the non-displayed boards
are not active.
-- Added saving and restoring the state of the relays after a reset
or power on. The S and H masks are saved to the EEPROM. When the
sketch starts to run the S and H masks are read from EEPROM. The
masks are then used to restore the state of the relays.
= Enabled with the "USE_EEPROM" define.
-- Added the "I" command. The I command displays a comma-separated
values (CSV) format of the status of the relays.
= Command format: <'board''relay'I>
-= Relay "0" display the status of all the relays on a board.
= Output format:
-= Relay status:
--= Off: 0
--= Set: s
--= Hold: h
-= Board: (relay 0)
i,'board',0,'relay 1 state','relay 2 state', ... 'relay 7 state'
--= Example:
i,A,0,s,0,0,h,0,0,0
-= Relay:
i,'board','relay','state'
--= Examples:
i,A,1,0
i,A,2,s
1,A,5,h
-- No changes where made to the LED 8x8 display.
-- BUG - Touch Screen: Sometimes the relay status is wrong. Selecting a
board will update the relay status. The root cause may be floating
emulation.
TASS Software v0.60 (24 January 2016)
-- Added #ifdef for "COMBINE_A_B" which causes boards A and B to act
as a single board for purposes of the "S" command. This allows for
a 16 input switch.
-- Added #ifdef for "D_DOUBLE_POLE" which gangs together ports 1-5, 2-6,
3-7, and 4-8 to create a four-throw double-pole switch. e.g., enter
<D1S> and both relays 1 and 5 will energize, or enter <D7S> and both
relays 3 and 7 will energize.
-- Additional logic fixes and code cleanup
TASS Software v0.51 (10 January 2016)
-- Lots of code cleanup, moving routines into their own file to simplify
the main loop.
-- If you tried versino 0.45, it probably didn't work as the routine to
write to the board was not called properly, and if it had been, it would
not have properly cleared unset relays. Both should be fixed now.
TASS Software v0.45 (16 December 2015)
-- MAJOR FIX. Restructured variables and logic for multi-board support
-- Added support for 8x8 LED matrix status display (USE_LED8X8)
-- Other cleanup
TASS Software v0.42 (4 October 2015)
-- Fixed bug in mask clearing that made the "U" command fail
-- Added function to allow display of relay and hold masks
-- Prettied up the TFT display a little
TASS Software v0.40
This version introduces support for Wiznet W5100 ethernet shields. When
enabled via the USE_W5100 define, it operates a telnet server on port 23
that accepts the same command syntax as the USB serial connection.
You'll need to enter network information in the main TASS.ino file.
There's an option "telnet_verbose" that determines what commands are
returned from the server. Setting to 0 means no echo of successful commands.
Setting to 1 will echo the raw command setting, e.g. "<A1S>". Setting to
2 will echo the raw setting plus additional description.
Note that the server is very primitive. I am not sure how it will work if
more than one client connects to the board. You Have Been Warned.
TASS Software v0.32
This version is the first release that is minimally usable. It supports
commands via USB and also will work with an Adafruit 2.8 inch capacitive
TFT touchscreen (product ID 1947). To enable the touchscreen, use the
IS_TFT define. If the touchscreen is enabled, it must be present for the
code to run. You Have Been Warned.