Skip to content

Latest commit

 

History

History
584 lines (399 loc) · 23.1 KB

README.md

File metadata and controls

584 lines (399 loc) · 23.1 KB

OpenThread on nRF52840 Example

Thread Certified Component

This directory contains example platform drivers for Nordic Semiconductor nRF52840 SoC. The OpenThread stack has been officially certified as a Thread Certified Component on this platform.

Note: For new projects, you should use nRF Connect SDK. nRF5 SDK for Thread and Zigbee is a legacy solution and only provided in maintenance mode.

To facilitate Thread products development with the nRF52840 platform, Nordic Semiconductor provides nRF5 SDK for Thread and Zigbee. See Nordic Semiconductor's nRF5 SDK for Thread and Zigbee section for more details.

Prerequisites

After cloning the repo, you must initialize the git submodule.

$ git submodule update --init

Before you start building the examples, you must download and install the toolchain and the tools required for flashing and debugging.

Toolchain

Download and install the GNU toolchain for ARM Cortex-M.

To install the GNU toolchain and its dependencies, run the following commands in Bash:

$ cd <path-to-ot-nrf528xx>
$ ./script/bootstrap

Flashing and debugging tools

Install the nRF Command Line Tools to flash, debug, and make use of logging features on the nRF52840 DK with SEGGER J-Link.

Building the examples

To build the examples, run the following command in Bash:

$ cd <path-to-ot-nrf528xx>
$ ./script/build nrf52840 UART_trans

After a successful build, the elf files can be found in <path-to-ot-nrf528xx>/build/bin/*. You can convert them to hex using arm-none-eabi-objcopy:

$ arm-none-eabi-objcopy -O ihex build/bin/ot-cli-ftd ot-cli-ftd.hex

USB CDC ACM support

You can build the libraries with support for the native USB CDC ACM as a serial transport. To do so, build the firmware with the following parameter:

$ ./script/build nrf52840 USB_trans

Note that the USB CDC ACM serial transport is not supported with Engineering sample A of the nRF52840 chip.

If you are using Windows 7 or earlier, you must load an additional USB CDC driver. The driver can be found in third_party/NordicSemiconductor/libraries/usb/nordic_cdc_acm_example.inf.

Bootloader support

The examples support the following bootloaders for performing a Device Firmware Upgrade (DFU):

  • USB bootloader
  • UART bootloader
  • BLE bootloader

The support for a particular bootloader can be enabled by adding the following option:

  • USB: -DOT_BOOTLOADER=USB
  • UART: -DOT_BOOTLOADER=UART
  • BLE: -DOT_BOOTLOADER=BLE

nRF52840 dongle support (PCA10059)

You can build the libraries with support for the USB bootloader with USB DFU trigger support in PCA10059. As this dongle uses the native USB support, you must enable it as well.

To build the libraries, build with the following parameters:

$ ./script/build nrf52840 USB_trans -DOT_BOOTLOADER=USB

See nRF52840 Dongle Programming for more details about how to use the USB bootloader.

Native SPI support

You can build the libraries with support for native SPI Slave. To build the libraries, build with the following parameter:

$ ./script/build nrf52840 SPI_trans_NCP

With this option enabled, SPI communication between the NCP example and wpantund is possible (provided that the wpantund host supports SPI Master). To achieve that, an appropriate SPI device should be chosen in wpantund configuration file, /etc/wpantund.conf. You can find an example below.

Config:NCP:SocketPath "system:/usr/bin/spi-hdlc-adapter --gpio-int /sys/class/gpio/gpio25 /dev/spidev0.0"

In this example, spi-hdlc-adapter is a tool that you can use to communicate between NCP and wpantund over SPI. For this example, spi-hdlc-adapter is installed in /usr/bin.

The default SPI Slave pin configuration for nRF52840 is defined in examples/platforms/nrf52840/transport-config.h.

Note that the native SPI Slave support is not intended to be used with Engineering sample A of the nRF52840 chip due to single transfer size limitation.

Optional prefix for compiler command

You can prefix the compiler command using the CCPREFIX parameter. This speeds up the compilation when you use tools like ccache. Example usage:

$ ./script/build nrf52840 USB_trans CCPREFIX=ccache

CryptoCell 310 support

By default, OpenThread uses mbedTLS library with support for CryptoCell 310 hardware acceleration of cryptographic operations. When building the application, an explicit setup is needed (error checking omitted):

mbedtls_platform_set_calloc_free(calloc, free);
mbedtls_platform_setup(NULL);

When building an external application with OpenThread libraries and CryptoCell 310 hardware acceleration, use the following configuration:

  • Crypto libraries:
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedcrypto_shared.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedtls_tls_vanilla.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedtls_x509_vanilla.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedcrypto_cc3xx.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libnrf_cc310_platform_0.9.4.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedcrypto_oberon.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedtls_base_vanilla.a
  • Include directories:
    • third_party/NordicSemiconductor/libraries/nrf_security/mbedtls_platform_config
    • third_party/NordicSemiconductor/libraries/nrf_security/include
    • third_party/NordicSemiconductor/libraries/nrf_security/config
    • third_party/NordicSemiconductor/libraries/nrf_security/nrf_cc310_platform/include
  • Defines:
    • MBEDTLS_CONFIG_FILE set to "nrf-config.h"
    • MBEDTLS_USER_CONFIG_FILE set to "nrf52840-mbedtls-config.h"

Optional disabling of CryptoCell 310 support

By default, OpenThread uses mbedTLS library with support for CryptoCell 310 hardware acceleration of cryptographic operations. You can disable CryptoCell 310 and use software cryptography instead by building OpenThread with the following parameter:

$ ./script/build nrf52840 soft_crypto

When building an external application with OpenThread libraries and software cryptography, use the following configuration:

  • Crypto libraries:
    • output/nrf52840/lib/libmbedcrypto.a (present after successful build)
  • Include directories:
    • third_party/NordicSemiconductor/libraries/nrf_security/mbedtls_platform_config
    • third_party/mbedtls
    • third_party/mbedtls/repo/include
  • Defines:
    • MBEDTLS_CONFIG_FILE set to "mbedtls-config.h"
    • MBEDTLS_USER_CONFIG_FILE set to "nrf52840-mbedtls-config.h"

CryptoCell 310 abort mechanism

The CryptoCell 310 platform implements an abort mechanism. By default, any fault in the CryptoCell 310 library results in the system reset. This behavior can be changed by a call to the nrf_cc310_platform_set_abort() function. This function must be called before mbedtls_platform_setup:

void nrf_cc310_platform_set_abort(
	nrf_cc310_platform_abort_apis_t const * const apis)

CryptoCell 310 RTOS support

The hardware-accelerated mbedTLS library supports access from multiple threads. By default, simple blocking implementation of mutexes is used. The locking mechanism can be replaced by using the nrf_cc310_platform_set_mutexes() function. This function must be called before mbedtls_platform_setup:

void nrf_cc310_platform_set_mutexes(nrf_cc310_platform_mutex_apis_t const * const apis,
                                    nrf_cc310_platform_mutexes_t const * const mutexes)

The sample implementation of mutexes for FreeRTOS and Zephyr operating systems can be found in nrf_cc3xx_platform_mutex_freertos.c and nrf_cc3xx_platform_mutex_zephyr.c. Both files implement the function int nrf_cc310_platform_mutex_init(void). This function must be called before mbedtls_platform_setup.

The sample implementation of the abort functionality for FreeRTOS and Zephyr operating systems can be found in nrf_cc3xx_platform_abort_freertos.c and nrf_cc3xx_platform_abort_zephyr.c. Both files implement the function void nrf_cc310_platform_abort_init(void). This function must be called before mbedtls_platform_setup.

The typical setup in the RTOS environment (error checking omitted) is as follows:

mbedtls_platform_set_calloc_free(calloc, free);
nrf_cc310_platform_abort_init();
nrf_cc310_platform_mutex_init();
mbedtls_platform_setup(NULL);

When building an external application that uses RTOS with OpenThread libraries and the CryptoCell 310 hardware acceleration, use the following configuration:

  • Crypto libraries:
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedcrypto_shared.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedtls_tls_vanilla.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedtls_x509_vanilla.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedcrypto_cc3xx.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libnrf_cc310_platform_0.9.4.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedcrypto_oberon.a
    • third_party/NordicSemiconductor/libraries/nrf_security/lib/libmbedtls_base_vanilla.a
  • Include directories:
    • third_party/NordicSemiconductor/libraries/nrf_security/mbedtls_platform_config
    • third_party/NordicSemiconductor/libraries/nrf_security/include
    • third_party/NordicSemiconductor/libraries/nrf_security/config
    • third_party/NordicSemiconductor/libraries/nrf_security/nrf_cc310_platform/include
  • Defines:
    • MBEDTLS_CONFIG_FILE set to "nrf-config.h"
    • MBEDTLS_USER_CONFIG_FILE set to "nrf52840-mbedtls-config.h"
  • Sources:
    • nrf_cc3xx_platform_mutex_freertos.c or nrf_cc3xx_platform_mutex_zephyr.c from third_party/NordicSemiconductor/libraries/nrf_security/nrf_cc310_platform/src, depending on the RTOS used.
    • nrf_cc3xx_platform_abort_freertos.c or nrf_cc3xx_platform_abort_zephyr.c from third_party/NordicSemiconductor/libraries/nrf_security/nrf_cc310_platform/src, depending on the RTOS used.

See mbedTls Thread Safety and Multi Threading for more details.

Optional software only mbedTLS threading support

By default, the software-only mbedTLS library is built without support for multiple threads. You can enable this built-in support by building OpenThread with the following parameter:

$ ./script/build nrf52840 soft_crypto_threading

The simple mutex definition is used as shown below:

typedef void * mbedtls_threading_mutex_t;

However, you can modify it, by providing a path to a header file with proper definition. To do that, build OpenThread with the following parameter:

$ ./script/build soft_crypto_threading MBEDTLS_THREADING_MUTEX_DEF="path_to_a_header_file_with_mutex_definition.h"

When building an external application that uses RTOS with OpenThread libraries and software cryptography, use the following configuration:

  • Crypto libraries:
    • output/nrf52840/lib/libmbedcrypto.a (present after successful build)
  • Include directories:
    • third_party/NordicSemiconductor/libraries/nrf_security/mbedtls_platform_config
    • third_party/mbedtls
    • third_party/mbedtls/repo/include
    • third_party/NordicSemiconductor/libraries/nrf_security/include/software-only-threading
  • Defines:
    • MBEDTLS_CONFIG_FILE set to "mbedtls-config.h"
    • MBEDTLS_USER_CONFIG_FILE set to "nrf52840-mbedtls-config.h"
    • MBEDTLS_THREADING_C
    • MBEDTLS_THREADING_ALT

See mbedTls Thread Safety and Multi Threading for more details.

IEEE EUI-64 address

When the Thread device is configured to obtain the Thread Network security credentials with either Thread Commissioning or an out-of-band method, the extended MAC address should be constructed out of the globally unique IEEE EUI-64.

The IEEE EUI-64 address consists of two parts:

  • 24 bits of MA-L (MAC Address Block Large), formerly called OUI (Organizationally Unique Identifier)
  • 40-bit device unique identifier

By default, the device uses Nordic Semiconductor's MA-L (f4-ce-36). You can modify it by overwriting the OPENTHREAD_CONFIG_STACK_VENDOR_OUI define, located in the openthread-core-nrf52840-config.h file. This value must be publicly registered by the IEEE Registration Authority.

You can also provide the full IEEE EUI-64 address by providing a custom otPlatRadioGetIeeeEui64 function. To do this, define the flag OPENTHREAD_CONFIG_ENABLE_PLATFORM_EUI64_CUSTOM_SOURCE.

After the Thread Network security credentials have been successfully obtained, the device uses randomly generated extended MAC address.

Flashing the binaries

Flash the compiled binaries onto nRF52840 using nrfjprog which is part of the nRF Command Line Tools.

$ nrfjprog -f nrf52 --chiperase --program ot-cli-ftd.hex --reset

Running the example

To test the example:

  1. Prepare two boards with the flashed CLI Example (as shown above). The CLI FTD example uses the direct UART connection.

  2. Open a terminal connection on two boards:

    a. Start a terminal emulator like screen.

    b. Connect to the used COM port with the following direct UART settings:

    • Baud rate: 115200

    • 8 data bits

    • 1 stop bit

    • No parity

    • HW flow control: RTS/CTS This allows you to view the raw UART output.

      On Linux system a port name should be called e.g. /dev/ttyACM0 or /dev/ttyACM1.

    c. Run the following command to connect to a board.

    screen /dev/ttyACM0 115200

    Now you are connected with the CLI.

  3. Use the following commands to form a network on the first board.

    > dataset init new
    Done
    > dataset
    Active Timestamp: 1
    Channel: 13
    Channel Mask: 0x07fff800
    Ext PAN ID: d63e8e3e495ebbc3
    Mesh Local Prefix: fd3d:b50b:f96d:722d::/64
    Network Key: dfd34f0f05cad978ec4e32b0413038ff
    Network Name: OpenThread-8f28
    PAN ID: 0x8f28
    PSKc: c23a76e98f1a6483639b1ac1271e2e27
    Security Policy: 0, onrcb
    Done
    > dataset commit active
    Done
    > ifconfig up
    Done
    > thread start
    Done

    After a couple of seconds the node will become a Leader of the network.

    > state
    leader
  4. Use the following commands to attach to the network on the second board.

    > dataset networkkey dfd34f0f05cad978ec4e32b0413038ff
    Done
    > dataset commit active
    Done
    > ifconfig up
    Done
    > thread start
    Done

    After a couple of seconds the second node will attach and become a Child.

    > state
    child
  5. List all IPv6 addresses of the first board.

    > ipaddr
    fd3d:b50b:f96d:722d:0:ff:fe00:fc00
    fd3d:b50b:f96d:722d:0:ff:fe00:c00
    fd3d:b50b:f96d:722d:7a73:bff6:9093:9117
    fe80:0:0:0:6c41:9001:f3d6:4148
    Done
  6. Choose one of them and send an ICMPv6 ping from the second board.

    > ping fd3d:b50b:f96d:722d:7a73:bff6:9093:9117
    16 bytes from fd3d:b50b:f96d:722d:558:f56b:d688:799: icmp_seq=1 hlim=64 time=24ms

For a list of all available commands, visit OpenThread CLI Reference README.md.

SEGGER J-Link tools

SEGGER J-Link tools allow to debug and flash generated firmware using on-board debugger or external one.

Working with RTT logging

By default, the OpenThread's logging module provides functions to output logging information over SEGGER's Real Time Transfer (RTT).

You can set the desired log level by using the OPENTHREAD_CONFIG_LOG_LEVEL define.

To enable the highest verbosity level, append -DOT_FULL_LOGS=ON flag to the build command:

$ ./script/build nrf52840 UART_trans -DOT_FULL_LOGS=ON

Enable logging on Windows

  1. Connect the DK to your machine with a USB cable.
  2. Run J-Link RTT Viewer. The configuration window appears.
  3. From the Specify Target Device dropdown menu, select NRF52840_XXAA.
  4. From the Target Interface & Speed dropdown menu, select SWD.

Enable logging on Linux

  1. Connect the DK to your machine with a USB cable.
  2. Run JLinkExe to connect to the target. For example:
JLinkExe -device NRF52840_XXAA -if SWD -speed 4000 -autoconnect 1 -SelectEmuBySN <SEGGER_ID> -RTTTelnetPort 19021
  1. Run JLinkRTTTelnet to obtain the RTT logs from the connected device in a separate console. For example:
JLinkRTTClient -RTTTelnetPort 19021

Mass Storage Device known issue

Depending on your version, due to a known issue in SEGGER's J-Link firmware, you might experience data corruption or data drops if you use the serial port. You can avoid this issue by disabling the Mass Storage Device.

Disabling the Mass Storage Device on Windows

  1. Connect the DK to your machine with a USB cable.
  2. Run J-Link Commander. The configuration window appears.
  3. From the Specify Target Device dropdown menu, select NRF52840_XXAA.
  4. From the Target Interface & Speed dropdown menu, select SWD.
  5. Run the following command:
MSDDisable
  1. Power cycle the DK.

Disabling the Mass Storage Device on Linux

  1. Connect the DK to your machine with a USB cable.
  2. Run JLinkExe to connect to the target. For example:
JLinkExe -device NRF52840_XXAA -if SWD -speed 4000 -autoconnect 1 -SelectEmuBySN <SEGGER_ID>
  1. Run the following command:
MSDDisable
  1. Power cycle the DK.

Hardware Flow Control detection

By default, SEGGER J-Link automatically detects at runtime whether the target is using Hardware Flow Control (HWFC).

The automatic HWFC detection is done by driving P0.07 (Clear to Send - CTS) from the interface MCU and evaluating the state of P0.05 (Request to Send - RTS) when the first data is sent or received. If the state of P0.05 (RTS) is high, it is assumed that HWFC is not used.

To avoid potential race conditions, you can force HWFC and bypass the runtime auto-detection.

Disabling the HWFC detection on Windows

  1. Connect the DK to your machine with a USB cable.
  2. Run J-Link Commander. The configuration window appears.
  3. From the Specify Target Device dropdown menu, select NRF52840_XXAA.
  4. From the Target Interface & Speed dropdown menu, select SWD.
  5. Run the following command:
SetHWFC Force
  1. Power cycle the DK.

Disabling the HWFC detection on Linux

  1. Connect the DK to your machine with a USB cable.
  2. Run JLinkExe to connect to the target. For example:
JLinkExe -device NRF52840_XXAA -if SWD -speed 4000 -autoconnect 1 -SelectEmuBySN <SEGGER_ID>
  1. Run the following command:
SetHWFC Force
  1. Power cycle the DK.

You can find more details here.

Diagnostic module

nRF52840 port extends OpenThread Diagnostics Module.

You can read about all the features here.

Radio driver documentation

The radio driver comes with documentation that describes the operation of state machines in this module. To open the *.uml sequence diagrams, use PlantUML.

Verification

The following development kits have been used for testing and verification:

  • PCA10056 1.0.0
  • PCA10059 1.0.0
  • PCA10068 0.5.0

The following toolchains have been used for testing and verification:

  • GCC: GCC ARM Embedded 7.2018 q2 update
  • IAR: IAR Workbench 7.80.4
  • SES: SES 4.12
  • ARM: MDK-ARM version 5.25

The following OpenThread commits have been verified with nRF52840 and nRF52811 examples by Nordic Semiconductor:

  • 2279ef6 - 23.05.2019 (the latest checked)
  • 23ff101 - 22.03.2019
  • 704511c - 18.09.2018
  • ec59d7e - 06.04.2018
  • a89eb88 - 16.11.2017
  • 6a15261 - 29.06.2017
  • 030efba - 22.04.2017
  • de48acf - 02.03.2017
  • 50db58d - 23.01.2017

Nordic Semiconductor's nRF5 SDK for Thread and Zigbee

Note: For new projects, you should use nRF Connect SDK. nRF5 SDK for Thread and Zigbee is only provided in maintenance mode. While bare metal Thread samples are still maintained, there will not be new SDK releases.

Use nRF5 Software Development Kit (SDK) for Thread and Zigbee when developing Thread products with Nordic Semiconductor's advanced nRF52840, nRF52833 or nRF52811 SoCs.

The nRF5 SDK for Thread and Zigbee includes:

  • a pre-built OpenThread stack for the Nordic nRF52840 and nRF52811 SoCs,
  • support for hardware-accelerated cryptographic operations using ARM® CryptoCell-310,
  • unique Thread/Bluetooth Low Energy dynamic multiprotocol solution which allows for concurrent operation of Thread and Bluetooth Low Energy utilizing OpenThread and SoftDevice (Nordic’s Bluetooth Low Energy stack) with accompanying example applications,
  • Thread/Bluetooth Low Energy switched multiprotocol solution with accompanying example applications,
  • unique support for DFU-over-Thread (Device Firmware Upgrade),
  • examples to demonstrate interactions between nodes performing different Thread roles with the use of OpenThread and CoAP, CoAP Secure or MQTT-SN protocols,
  • support for OpenThread Network Co-Processor (NCP) and Radio Co-Processor (RCP) using UART, USB or SPI transport protocol,
  • Border Router and cloud connectivity example (e.g. with Google Cloud Platform),
  • Thread native commissioning with NFC example,
  • example applications demonstrating the use of FreeRTOS with OpenThread,
  • support for IAR, Keil MDK-ARM and SEGGER Embedded Studio (SES) IDEs for OpenThread stack and all example applications,
  • range of PC tools including Thread Topology Monitor and nRF Sniffer for 802.15.4,
  • software modules inherited from the nRF5 SDK e.g. peripheral drivers, NFC libraries, Bluetooth Low Energy libraries etc.