olsrd.conf

#
# olsr.org OLSR daemon config file
#
# Lines starting with a # are discarded
#
# This file was shipped with the debian olsrd package
#

# Debug level(0-9)
# If set to 0 the daemon runs in the background

DebugLevel	1

# the interface the mesh runs on is specified at run time using the -i flag

InterfaceDefaults
{
  # Olsrd can autodetect changes in NIC configurations (IP address
  # changes etc.).  This is enabled by default and the interval to
  # poll for changes on is defined by NicChgsPollInt.  This polling
  # can be disabled pr. NIC by setting AutoDetectChanges to no.

  #AutoDetectChanges            no

  # IPv4 broadcast address to use. The
  # one usefull example would be 255.255.255.255
  # If not defined the broadcastaddress
  # every card is configured with is used

  Ip4Broadcast		255.255.255.255

  # IPv6 address scope to use.
  # Must be 'site-local' or 'global'

  #Ip6AddrType		site-local

  # IPv6 multicast address to use when
  # using site-local addresses.
  # If not defined, ff05::15 is used

  #Ip6MulticastSite		ff05::11

  # IPv6 multicast address to use when
  # using global addresses
  # If not defined, ff0e::1 is used

  #Ip6MulticastGlobal	ff0e::1


  # Emission intervals.
  # If not defined, RFC proposed values will
  # be used in most cases.

  # Hello interval in seconds(float)
    HelloInterval		6.0

  # HELLO validity time
    HelloValidityTime		600.0

  # TC interval in seconds(float)
    TcInterval			0.5

  # TC validity time
    TcValidityTime		300.0

  # MID interval in seconds(float)
    MidInterval			10.0

  # MID validity time
    MidValidityTime		300.0

  # HNA interval in seconds(float)
    HnaInterval			10.0

  # HNA validity time
    HnaValidityTime		300.0

  # When multiple links exist between hosts
  # the weight of interface is used to determine
  # the link to use. Normally the weight is
  # automatically calculated by olsrd based
  # on the characteristics of the interface,
  # but here you can specify a fixed value.
  # Olsrd will choose links with the lowest value.

  #Weight 0


  # If a certain route should be preferred
  # or ignored by the mesh, the Link Quality
  # value of a node can be multiplied with a factor
  # entered here. In the example the route
  # using 192.168.0.1 would rather be ignored.
  # A multiplier of 0.5 will result in a small
  # (bad) LinkQuality value and a high (bad)
  # ETX value.

  #LinkQualityMult 192.168.0.1 0.5

  # This multiplier applies to all other nodes
  # LinkQualityMult default 0.8
}

## these settings should work for funkfeuer, freifunk, etc.
# Fisheye mechanism for TC messages 0=off, 1=on
LinkQualityFishEye 1
#LinkQualityAlgorithm "etx_ff"

## if using commotionwireless.net, comment the line above and uncomment these:
#LinkQualityFishEye 0
#LinkQualityAlgorithm "etx_ffeth"

# IP version to use (4 or 6)

IpVersion	4

# Clear the screen each time the internal state changes

ClearScreen     yes

# HNA IPv4 routes
# syntax: netaddr netmask
# Example Internet gateway:
# 0.0.0.0 0.0.0.0

Hna4
{
#   Internet gateway:
#   0.0.0.0      0.0.0.0
#   more entries can be added:
#   192.168.1.0  255.255.255.0
}

# HNA IPv6 routes
# syntax: netaddr prefix
# Example Internet gateway:
Hna6
{
#   Internet gateway:
#   ::              0
#   more entries can be added:
#   fec0:2200:106:: 48
}


# Should olsrd keep on running even if there are
# no interfaces available? This is a good idea
# for a PCMCIA/USB hotswap environment.
# "yes" OR "no"

AllowNoInt	yes

# TOS(type of service) value for
# the IP header of control traffic.
# If not set it will default to 16

#TosValue	16

# The fixed willingness to use(0-7)
# If not set willingness will be calculated
# dynamically based on battery/power status
# if such information is available

Willingness    	7

# Allow processes like the GUI front-end
# to connect to the daemon.

IpcConnect
{
     # Determines how many simultaneously
     # IPC connections that will be allowed
     # Setting this to 0 disables IPC

     MaxConnections  2

     # By default only 127.0.0.1 is allowed
     # to connect. Here allowed hosts can
     # be added

     Host            127.0.0.1
     Host            192.168.7.1
     Host            192.168.7.2
     Host            192.168.7.3
     Host            192.168.7.4
     Host            192.168.7.10
     Host            192.168.7.11
     #Host            10.0.0.5

     # You can also specify entire net-ranges
     # that are allowed to connect. Multiple
     # entries are allowed

     Net             192.168.7.0 192.168.7.255
}

# Wether to use hysteresis or not
# Hysteresis adds more robustness to the
# link sensing but delays neighbor registration.
# Used by default. 'yes' or 'no'
# Do not use hysteresis with ETX!

UseHysteresis	no

# Hysteresis parameters
# Do not alter these unless you know
# what you are doing!
# Set to auto by default. Allowed
# values are floating point values
# in the interval 0,1
# THR_LOW must always be lower than
# THR_HIGH.

#HystScaling	0.50
#HystThrHigh	0.80
#HystThrLow	0.30


# Link quality level
# 0 = do not use link quality
# 1 = use link quality for MPR selection
# 2 = use link quality for MPR selection and routing
# Defaults to 0

LinkQualityLevel	2

# Polling rate in seconds(float).
# Default value 0.05 sec

Pollrate	0.1


# TC redundancy
# Specifies how much neighbor info should
# be sent in TC messages
# Possible values are:
# 0 - only send MPR selectors
# 1 - send MPR selectors and MPRs
# 2 - send all neighbors
#
# defaults to 0

TcRedundancy	2


#
# MPR coverage
# Specifies how many MPRs a node should
# try select to reach every 2 hop neighbor
#
# Can be set to any integer >0
#
# defaults to 1

MprCoverage	5


# Olsrd plugins to load
# This must be the absolute path to the file
# or the loader will use the following scheme:
# - Try the paths in the LD_LIBRARY_PATH
#   environment variable.
# - The list of libraries cached in /etc/ld.so.cache
# - /lib, followed by /usr/lib

# Configuration examples for plugins:
# see /usr/share/doc/olsrd-plugins/ for some for documentation

# these are loaded from LD_LIBRARY_PATH
#LoadPlugin "olsrd_httpinfo.so.0.1"
#{
  # defaults to 1978
  #PlParam "Port" "8080"
  # if you dont set these, the default is to listen only on the loopback device
  #PlParam "Host"   "80.23.53.22"
  #PlParam "Net"    "10.0.0.0 255.0.0.0"
  #PlParam "Net" "0.0.0.0 0.0.0.0"
  #PlParam "Host"  "127.0.0.1"
#}

## for more info: http://olsr.org/?q=txtinfo_plugin
#LoadPlugin "olsrd_txtinfo.so.0.1"
#{
#  PlParam     "port"   "2006"
#  PlParam     "accept" "0.0.0.0"
#}

## for more info: http://olsr.org/?q=jsoninfo_plugin
#LoadPlugin "olsrd_jsoninfo.so.0.0"
#{
#  PlParam     "port"   "9090"
#  PlParam     "accept" "0.0.0.0"
#}

# useful if your machine has an uplink
#LoadPlugin "olsrd_dyn_gw.so.0.4"
#{
  # Here parameters are set to be sent to the
  # plugin. Theese are on the form "key" "value".
  # Parameters ofcause, differs from plugin to plugin.
  # Consult the documentation of your plugin for details.

  # Example: dyn_gw params

  # how often to check for Internet connectivity
  # defaults to 5 secs
  #PlParam     "Interval"   "40"

  # if one or more IPv4 addresses are given, do a ping on these in
  # descending order to validate that there is not only an entry in
  # routing table, but also a real internet connection. If any of
  # these addresses could be pinged successfully, the test was
  # succesful, i.e. if the ping on the 1st address was successful,the
  # 2nd won't be pinged
  #PlParam     "Ping"       "141.1.1.1"
  #PlParam     "Ping"       "194.25.2.129"
#}

#LoadPlugin "olsrd_nameservice.so.0.2"
#{
  #PlParam "name" "xxx"
  #PlParam "a.b.c.d" "xxx-eth"
  #PlParam "a.b.c.e" "xxx-bbb"
  #PlParam "a.b.c.f" "xxx-olsr"
  #PlParam "suffix" ".olsr"
#}

#LoadPlugin "olsrd_dot_draw.so.0.3"
#{
  # accept connection from IP:
  # default 127.0.0.1 (localhost)
  #PlParam     "accept" "192.168.0.5"
  #PlParam     "port" "2004"
#}