Skip to content

Latest commit

 

History

History
510 lines (336 loc) · 13.8 KB

README.md

File metadata and controls

510 lines (336 loc) · 13.8 KB

CUSTOM boards with STM32

Feel free to propose your custom boards support in mbed-os!

Table of Contents

Usage

In your application, clone this repo.

git clone https://github.com/ARMmbed/stm32customtargets.git

Copy custom_targets.json

cp stm32customtargets/custom_targets.json .

For some targets, you have to customize the configuration in your local mbed_app.json.

Details are explained for each target below, but you can also use the mbed_app_template.json file as example.

Then build your target with

  • CLI1:
mbed compile -m XXX -t XXX
  • CLI2:

Add in the application CMakeLists.txt:

add_subdirectory(stm32customtargets)

And build:

mbedtools compile -m XXX -t XXX

GENERIC BOARDS

A "generic" board is a mbed-os "virtual" target with a pure STM32 MCU.

Goal is to make real custom boards creation very easy as we ensure that build has alrady been tested.

Check the GENERIC_TARGET branch in this repo:

https://github.com/ARMmbed/stm32customtargets/tree/GENERIC_TARGET

STM32F1

BLUEPILL

MCU: STM32F103C8T6

TARGET: BLUEPILL_F103C8

source: https://os.mbed.com/users/hudakz/code/mbed-os-bluepill/

(https://os.mbed.com/users/hudakz/code/STM32F103C8T6_Hello/)

STM32F4

CORE2

MCU: STM32F407ZG

TARGET: CORE2

https://github.com/byq77/core2-mbed6-template

STM32L0

MURATA LPWAN Wireless Module

MCU: STM32L082CZ

TARGET: MTB_MURATA_ABZ

https://wireless.murata.com/type-abz-078.html

  • LORA is not enabled by default. You need to update your local mbed_app.json file:
{
    "target_overrides": {
        "MTB_MURATA_ABZ": {
            "target.components_add":             ["SX1276"],
            "sx1276-lora-driver.spi-mosi":       "LORA_SPI_MOSI",
            "sx1276-lora-driver.spi-miso":       "LORA_SPI_MISO",
            "sx1276-lora-driver.spi-sclk":       "LORA_SPI_SCLK",
            "sx1276-lora-driver.spi-cs":         "LORA_CS",
            "sx1276-lora-driver.reset":          "LORA_RESET",
            "sx1276-lora-driver.dio0":           "LORA_DIO0",
            "sx1276-lora-driver.dio1":           "LORA_DIO1",
            "sx1276-lora-driver.dio2":           "LORA_DIO2",
            "sx1276-lora-driver.dio3":           "LORA_DIO3",
            "sx1276-lora-driver.txctl":          "LORA_ANT_TX",
            "sx1276-lora-driver.rxctl":          "LORA_ANT_RX",
            "sx1276-lora-driver.pwr-amp-ctl":    "LORA_ANT_BOOST"
        }
    }
}

If you need to Low Power with VDD TXCO like b-l072z-lrwan1, then you need JP9 positionned 1-2. And reflect the pin used for that because it's defined to NC by default.

{
    "target_overrides": {
        "MTB_MURATA_ABZ": {
            "sx1276-lora-driver.tcxo":           "PA_12"
        }
    }
}

MURATA Grasshopper

MCU: STM32L082CZ

TARGET: GRASSHOPPER TleraCorp

  • LORA is not enabled by default. You need to update your local mbed_app.json file:
{
    "target_overrides": {
        "GRASSHOPPER": {
            "target.components_add":             ["SX1276"],
            "sx1276-lora-driver.spi-mosi":       "LORA_SPI_MOSI",
            "sx1276-lora-driver.spi-miso":       "LORA_SPI_MISO",
            "sx1276-lora-driver.spi-sclk":       "LORA_SPI_SCLK",
            "sx1276-lora-driver.spi-cs":         "LORA_CS",
            "sx1276-lora-driver.reset":          "LORA_RESET",
            "sx1276-lora-driver.dio0":           "LORA_DIO0",
            "sx1276-lora-driver.dio1":           "LORA_DIO1",
            "sx1276-lora-driver.dio2":           "LORA_DIO2",
            "sx1276-lora-driver.dio3":           "LORA_DIO3",
            "sx1276-lora-driver.txctl":          "LORA_ANT_TX",
            "sx1276-lora-driver.rxctl":          "LORA_ANT_RX",
            "sx1276-lora-driver.pwr-amp-ctl":    "LORA_ANT_BOOST",
            "sx1276-lora-driver.tcxo":           "LORA_VDD_TXCO"
        }
    }
}

MURATA Gnat

MCU: STM32L082CZ

https://www.tindie.com/products/tleracorp/gnat-loragnss-asset-tracker/

TARGET: GNAT TleraCorp

  • LORA is not enabled by default. You need to update your local mbed_app.json file:
{
    "target_overrides": {
        "GNAT": {
            "target.components_add":             ["SX1276"],
            "sx1276-lora-driver.spi-mosi":       "LORA_SPI_MOSI",
            "sx1276-lora-driver.spi-miso":       "LORA_SPI_MISO",
            "sx1276-lora-driver.spi-sclk":       "LORA_SPI_SCLK",
            "sx1276-lora-driver.spi-cs":         "LORA_CS",
            "sx1276-lora-driver.reset":          "LORA_RESET",
            "sx1276-lora-driver.dio0":           "LORA_DIO0",
            "sx1276-lora-driver.dio1":           "LORA_DIO1",
            "sx1276-lora-driver.dio2":           "LORA_DIO2",
            "sx1276-lora-driver.dio3":           "LORA_DIO3",
            "sx1276-lora-driver.txctl":          "LORA_ANT_TX",
            "sx1276-lora-driver.rxctl":          "LORA_ANT_RX",
            "sx1276-lora-driver.pwr-amp-ctl":    "LORA_ANT_BOOST",
            "sx1276-lora-driver.tcxo":           "LORA_VDD_TXCO"
        }
    }
}

STM32L4

STWIN SensorTile Wireless Industrial Node development kit

MCU: STM32L4R9ZI

TARGET: STWIN

https://www.st.com/en/evaluation-tools/steval-stwinkt1.html

  • BLE is enabled by default

STM32WL

Seeed Studio LoRa E5

MCU: STM32WLE5JC

TARGET: LORA_E5

https://www.seeedstudio.com/LoRa-E5-Wireless-Module-p-4745.html

LoRa-E5 use only RFO_HP for TX power, so for all boards using this module you need to add this to your mbed_app.json on section target_overrides

   "LORA_E5": {
      "stm32wl-lora-driver.rf_switch_config": 2
   }

Seeed Studio LoRa E5 Mini

TARGET: LORA_E5_MINI

Use LoRa E5 modulen basic board with USB/Serial and headers

https://www.seeedstudio.com/LoRa-E5-mini-STM32WLE5JC-p-4869.html

Seeed Studio LoRa E5 Dev Board

TARGET: LORA_E5_DEV_BOARD

Use LoRa E5 module

https://www.seeedstudio.com/LoRa-E5-Dev-Kit-p-4868.html

  • RS485 Modbus
  • all LoRa-E5 pins exposed
  • temperature sensor
  • buttons
  • Led
  • GPIO to enable 3.3V and 5V for sensors
  • some grove sonnectors (I2C, Serial, ..)
  • Arduino form factor to plug shield

Charles's LoRa-E5 breakout board

TARGET: LORA_E5_BREAKOUT

https://github.com/hallard/LoRa-E5-Breakout

Use LoRa E5 module and added

  • FTDI 6 pins connector (:warning: use 3.3V FTDI One, not 5V)
  • Exposed JTAG pins needed to flash module (PA13-SWDIO / PA14-SWCLK / RESET)
  • Green Led on PB10 (LED1) reversed (1=OFF, 0=ON)
  • Red Led on PB5 (LED2) reversed (1=OFF, 0=ON)

for debug LEDs of breakout so you need to add this to your mbed_app.json on section target_overrides and don't forget also the rf_switch_config seen above

   "LORA_E5_BREAKOUT": {
      "stm32wl-lora-driver.rf_switch_config": 2,
      "stm32wl-lora-driver.debug_tx": "PB_5",
      "stm32wl-lora-driver.debug_rx": "PB_10",
      "stm32wl-lora-driver.debug_invert": 1
   }

Charles's LoRa-E5 Tiny

TARGET: LORA_E5_TINY

https://github.com/hallard/LoRa-E5-Tiny

Use LoRa E5 module with CR2450 cell coin

  • FTDI SMD 6 pads edge connector (:warning: use 3.3V FTDI One, not 5V)
  • JTAG SMD 6 pads edge connector to flash module (PA13-SWDIO / PA14-SWCLK / PB3-SWO / RESET)
  • Green Led on PB13
  • Red Led on PA9
  • 2 Tactile Switches (user PB4 and reset)
  • Stemma QWIIC I2C connector
  • PTH CR2450 battery holder

for debug LEDs of this board you need to add this to your mbed_app.json on section target_overrides and don't forget also the rf_switch_config seen above

   "LORA_E5_TINY": {
      "stm32wl-lora-driver.rf_switch_config": 2,
      "stm32wl-lora-driver.debug_tx": "PB_13",
      "stm32wl-lora-driver.debug_rx": "PA_9"
   }

RAK Wireless RAK3172

MCU: STM32WLE5CC

TARGET: RAK3172

RAK3172 use only RFO_HP for TX power and no TXCO so for all boards using this module you need to add this to your mbed_app.json on section target_overrides

   "RAK3172": {
      "stm32wl-lora-driver.rf_switch_config": 2,
      "stm32wl-lora-driver.crystal_select" : 0
   }

Charles's RAK3172 breakout board

TARGET: RAK3172_BREAKOUT

https://github.com/hallard/RAK3172-Breakout

Use RAK3172 and added

  • FTDI 6 pins connector (:warning: use 3.3V FTDI One, not 5V)
  • Exposed JTAG pins needed to flash module (PA13-SWDIO / PA14-SWCLK / RESET)
  • Green Led on PA10 (LED1) reversed (1=OFF, 0=ON)
  • Red Led on PA9 (LED2) reversed (1=OFF, 0=ON)
  • SMD CR2450 battery holder

For debug LEDs of breakout so you need to add this to your mbed_app.json on section target_overrides and don't forget also the rf_switch_config and crystal_select seen above

   "RAK3172_BREAKOUT": {
      "stm32wl-lora-driver.rf_switch_config": 2,
      "stm32wl-lora-driver.crystal_select" : 0,
      "stm32wl-lora-driver.debug_tx": "PA_10",
      "stm32wl-lora-driver.debug_rx": "PA_9",
      "stm32wl-lora-driver.debug_invert": 1
   }

RAK Wirekess RAK3172-SiP SOC

MCU: STM32WLE5CC

TARGET: RAK3172SIP

RAK3172-SIP SOC is just a SOC, you can build your own boards with this module, check below the usage for the RAK3272-SiP Breakout Board reference board and an example of board definition and usage.

RAK Wirekess RAK3272-SiP Breakout Board

MCU: STM32WLE5CC

TARGET: RAK3272_SIP_BREAKOUT

RAK3172-SIP SOC exists in two versions, both with TCXO connected to PB0 (so you can disable it for low power):

  • RAK3172-SIP using high power path (>14db) that use only RFO_HP for TX power, you need to add this to your mbed_app.json on section target_overrides
   "RAK3272_BREAKOUT": {
      "stm32wl-lora-driver.rf_switch_config": "RBI_CONF_RFO_HP",
      "stm32wl-lora-driver.crystal_select" : 1
   }
  • RAK3172LP-SIP using low power path only (<=14db) that use only RFO_LP for TX power, you need to add this to your mbed_app.json on section target_overrides
   "RAK3272_BREAKOUT": {
      "stm32wl-lora-driver.rf_switch_config": "RBI_CONF_RFO_LP",
      "stm32wl-lora-driver.crystal_select" : 1
   }

License

The software is provided under the Apache-2.0 license.

Contributions

Contributions to this project are accepted under the same license.

Automatic pull request checks

  • Build with CLI1 should be OK
python aci_build.py
  • Build with CLI2 should be OK
python aci_build.py --cli2

Note that build is using the mbed_app_template.json file as configuration file.

  • Standard Pin Names check should be OK

https://os.mbed.com/docs/mbed-os/latest/apis/standard-pin-names.html

python aci_build.py --pin

Manual pull request checks

  • Each target in custom_targets.json should be described in the README.md file
## <Full target name>

MCU: <STM32 MCU>

TARGET: <Target name for build>

<Link to a webpage describing this board>

<all other info is optional>

Note we limit image size to 200

  • Keep Table of Contents up to date

Automatic weekly non regression

A full non regression is executed each week-end

python aci_build.py --all
python aci_build.py --all --baremetal
python aci_build.py --all --cli2
python aci_build.py --all --cli2 --baremetal
python aci_build.py --all --pin

See in https://github.com/ARMmbed/stm32customtargets/actions