SPI flash and EEPROM dump of the ODI DFP-34x-2c2

[lehoangnb]

Its for ODI DFP-34x-2c2 with 8MB MX25L6433F flash and 24C04 EEPROM

SPI Flash info

• Flash name: MX25L6433F SPI 8MB
• File name: ODI_DFP-34X-2C2_factory_8M_v220923.bin
• sha256: 5e3572c2c6821b8f345d6564ae547aaf734b227c678744b276d311cb97006cd7
• Both layout is running 220923 @Anime4000 modified firmware

EEPROM info

• EEPROM name: 24C04 4K (512B) I2C (SOT23 package)
• File name: ODI_DFP-34X-2C2_eeprom_4K.bin
• sha256: 6342c4bdefee80e1ca238615c3840184eaec5cdae48dc403111bb5b09f96fef0

Notice

• Use only 3.3V level for both Flash and EEPROM
• In most case, flashing eeprom is not necessary

Download

ODI_DFP-34X-2C2_full_dump_v220923.zip

[Headcrabed]

Besides, eeprom need to be modified to switch to 2500basex mode for host device.

[Anime4000]

I linking this to main README.md

[duskyzaoKING]

Hi. Do you have the original .bin of the ODI? I lost access to the IP interface, and i dont wat to do UART as i have a RT809H programmer. Will flash direct the .bin with aligator clip. I will restore original firmware and then change to M114_sfp_ODI_PPPOE_210702 firmware because they do PPPoE auth. Do your firmware do PPPoE Auth ? I have a Chinese Switch Layer 3 and i am having a lot of probleming with low speed only using my switch L3. Maybe my switch have a problem with HiSGMII PHY, HiSGMII MAC and 2500Base-X? I lost access when i changed to LAN_SDS_MODE 6. As i did no know about your work, i bought the version DFP-34G-2C2 instead of DFP-34X-2C2. But as i checked in the repo, the newer version like mine come with realtek chip, maybe RTL9602(i lost access now but i checked in past in /proc/cpuinfo). So i am using always the X version of firmware. Do you know if i will loose anything using the G version? (mine using realtek chip too)

[duskyzaoKING]

The problem is my config has a flash set SDS that I lost access in IP interface. When you flash the firmware they preserve this config, so I still without access. But I done UART and switched backed SDS and recovery IP access.

lost entire night trying to do UART, and the morning I checked I lost one capacitor and two resistor 🤦‍♂️. As I have two units I checked the capacitors nF in other board and I am doing reverse engineering to find in one of my iPhone donate boards one capacitor and two resistors with same value. Already found the capacitor, just need to find resistor 🙏

[Headcrabed]

Pull out and plug in fiber 5 times in 30 seconds would reset everything(except loid stuff)

[duskyzaoKING]

I didn’t know. But this erase SDS value too? The parameter to get 2.5GB

[Headcrabed]

My stock firmware has a option to change speed mode in web interface, and it works when that blocked me out.

[duskyzaoKING]

Trying to Finding this two micro resistors 😂😂

[duskyzaoKING]

@Anime4000 i flashed you BIN but they didn’t come with your interface customization. Maybe is it in the eprom? I only flashed the SPI

[Anime4000]

@lehoangnb I have question,
My stick using different brand SPI Flash, something off-brand called CFEON.
It should be similar to MXIC MX25L6433F right?

[duskyzaoKING]

You can check in datasheet of the two SPI Flash. But i can confirm its compatible, because i flashed your .bin and mine SPI its MXIC and worked ok. The bin didnt come with your logo customization, but came with your OMCI info and other things

[Anime4000]

the GUI Customization not yet public 😅 just to make sure no issue or glitch

[lehoangnb]

Maybe similar if both have same size, (but be aware, kernel in firmware must have driver for SPI flash)

[Anime4000]

Alright, just to be safe, read multiple time, backup multiple time, compare and verify multiple time, I'll get back once required tool arrive