sun50i-h618-bananapi-m4berry.dts

// SPDX-License-Identifier: (GPL-2.0+ or MIT)
/*
 * Copyright (C) 2020 Arm Ltd.
 */

/dts-v1/;

#include "sun50i-h616.dtsi"
#include "sun50i-h616-cpu-opp.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/leds/common.h>

/ {
	model = "BananaPi M4 Berry";
	compatible = "BiPai,bananapi-m4berry", "allwinner,sun50i-h616";

	aliases {
		ethernet0 = &emac0;
		serial0 = &uart0;
		serial5 = &uart5;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	connector {
		compatible = "hdmi-connector";
		type = "d";

		port {
			hdmi_con_in: endpoint {
				remote-endpoint = <&hdmi_out_con>;
			};
		};
	};

	leds: leds {
		compatible = "gpio-leds";

		led-greed {
			label = "red_led";
			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
			linux,default-trigger = "heartbeat";
		};
	};

	wifi_usb {
		compatible = "usb-wifi";
		status = "okay";
		power_on_pin = <&pio 2 2 GPIO_ACTIVE_HIGH>; /* PC2 */
	};

	reg_vcc5v: vcc5v {
		/* board wide 5V supply directly from the USB-C socket */
		compatible = "regulator-fixed";
		regulator-name = "vcc-5v";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		regulator-always-on;
	};
};

&de {
	status = "okay";
};

&hdmi {
	//hvcc-supply = <&reg_bldo1>;
	status = "okay";
};

&hdmi_out {
	hdmi_out_con: endpoint {
		remote-endpoint = <&hdmi_con_in>;
	};
};

&gpu {
	mali-supply = <&reg_dcdc1>;
	status = "disabled";
};

&emac0 {
	pinctrl-names = "default";
	pinctrl-0 = <&ext_rgmii_pins>;
	phy-mode = "rgmii";
	phy-handle = <&ext_rgmii_phy>;
	allwinner,rx-delay-ps = <3100>;
	allwinner,tx-delay-ps = <700>;
	status = "okay";
};

&mdio0 {
	ext_rgmii_phy: ethernet-phy@1 {
		compatible = "ethernet-phy-ieee802.3-c22";
		reg = <1>;
	};
};

&mmc0 {
	vmmc-supply = <&reg_dldo1>;
	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
	bus-width = <4>;
	max-frequency = <50000000>;
	status = "okay";
};

&mmc2 {
	pinctrl-names = "default";

	vmmc-supply = <&reg_dldo1>;
	bus-width = <8>;
	non-removable;
	cap-mmc-hw-reset;
	status = "okay";
};

&r_i2c {
	status = "okay";

	axp313a: pmic@36 {
		compatible = "x-powers,axp313a";
		reg = <0x36>;
		wakeup-source;

		regulators{
			reg_dcdc1: dcdc1 {
				regulator-name = "axp313a-dcdc1";
				regulator-min-microvolt = <500000>;
				regulator-max-microvolt = <1100000>;
				regulator-step-delay-us = <25>;
				regulator-final-delay-us = <50>;
				regulator-always-on;
			};

			reg_dcdc2: dcdc2 {
				regulator-name = "axp313a-dcdc2";
				regulator-min-microvolt = <500000>;
				regulator-max-microvolt = <1200000>;
				regulator-step-delay-us = <25>;
				regulator-final-delay-us = <50>;
				regulator-ramp-delay = <200>;
				regulator-always-on;
			};

			reg_dcdc3: dcdc3 {
				regulator-name = "axp313a-dcdc3";
				regulator-min-microvolt = <1100000>;
				regulator-max-microvolt = <1100000>;
				regulator-step-delay-us = <25>;
				regulator-final-delay-us = <50>;
				regulator-always-on;
			};

			reg_aldo1: ldo1 {
				regulator-name = "axp313a-aldo1";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-step-delay-us = <25>;
				regulator-final-delay-us = <50>;
				regulator-always-on;
			};

			reg_dldo1: ldo2 {
				regulator-name = "axp313a-dldo1";
				regulator-min-microvolt = <3300000>;
				regulator-max-microvolt = <3300000>;
				regulator-step-delay-us = <25>;
				regulator-final-delay-us = <50>;
				regulator-always-on;
			};
		};
	};
};

&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_ph_pins>;
	status = "okay";
};

&usbotg {
	/*
	 * PHY0 pins are connected to a USB-C socket, but a role switch
	 * is not implemented: both CC pins are pulled to GND.
	 * The VBUS pins power the device, so a fixed peripheral mode
	 * is the best choice.
	 * The board can be powered via GPIOs, in this case port0 *can*
	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
	 * then provided by the GPIOs. Any user of this setup would
	 * need to adjust the DT accordingly: dr_mode set to "host",
	 * enabling OHCI0 and EHCI0.
	 */
	dr_mode = "peripheral";
	status = "okay";
};

&usbphy {
	usb1_vbus-supply = <&reg_vcc5v>;
	status = "okay";
};

&ehci0 {
	status = "disabled";
};

&ehci1 {
	status = "okay";
};

&ehci2 {
	status = "okay";
};

&ehci3 {
	status = "okay";
};

&ohci0 {
	status = "disabled";
};

&ohci1 {
	status = "okay";
};

&ohci2 {
	status = "okay";
};

&ohci3 {
	status = "okay";
};

&ir {
	pinctrl-names = "default";
	pinctrl-0 = <&ir_rx_pin>;
	status = "okay";
};

&i2c1 {
	status = "disabled";
};

&i2c2 {
	status = "disabled";
};

&i2c3 {
	status = "disabled";
};

&i2c4 {
	status = "disabled";
};

&uart1 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart1_ph_pins>, <&uart1_ph_rts_cts_pins>;
	status = "okay";
};

&uart2 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_ph_pins>;
	status = "disabled";
};

&uart5 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart5_ph_pins>;
	status = "okay";
};

&spi1 {
	status = "okay";
	#address-cells = <1>;
	#size-cells = <0>;
	pinctrl-names = "default";
	pinctrl-0 = <&spi1_pins>, <&spi1_cs1_pin>;

	spidev@1 {
		compatible = "rohm,dh2228fv";
		status = "okay";
		reg = <1>;
		spi-max-frequency = <1000000>;
	};
};

&codec {
	allwinner,audio-routing =
	        "Line Out", "LINEOUT";
	status = "okay";
};

&ahub_dam_plat {
	status = "okay";
};

&ahub_dam_mach {
	status = "okay";
};

&ahub1_plat {
	status = "okay";
};

&ahub1_mach {
	status = "okay";
};

&ahub_i2s2 {
	status = "okay";
};

&cpu0 {
	cpu-supply = <&reg_dcdc2>;
	status = "okay";
};