/
smc91x.h
1280 lines (1051 loc) · 37.8 KB
/
smc91x.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
/*------------------------------------------------------------------------
. smc91x.h - macros for SMSC's 91C9x/91C1xx single-chip Ethernet device.
.
. Copyright (C) 1996 by Erik Stahlman
. Copyright (C) 2001 Standard Microsystems Corporation
. Developed by Simple Network Magic Corporation
. Copyright (C) 2003 Monta Vista Software, Inc.
. Unified SMC91x driver by Nicolas Pitre
.
. This program is free software; you can redistribute it and/or modify
. it under the terms of the GNU General Public License as published by
. the Free Software Foundation; either version 2 of the License, or
. (at your option) any later version.
.
. This program is distributed in the hope that it will be useful,
. but WITHOUT ANY WARRANTY; without even the implied warranty of
. MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
. GNU General Public License for more details.
.
. You should have received a copy of the GNU General Public License
. along with this program; if not, write to the Free Software
. Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
.
. Information contained in this file was obtained from the LAN91C111
. manual from SMC. To get a copy, if you really want one, you can find
. information under www.smsc.com.
.
. Authors
. Erik Stahlman <erik@vt.edu>
. Daris A Nevil <dnevil@snmc.com>
. Nicolas Pitre <nico@fluxnic.net>
.
---------------------------------------------------------------------------*/
#ifndef _SMC91X_H_
#define _SMC91X_H_
#include <linux/smc91x.h>
/*
* Define your architecture specific bus configuration parameters here.
*/
#if defined(CONFIG_ARCH_LUBBOCK) ||\
defined(CONFIG_MACH_MAINSTONE) ||\
defined(CONFIG_MACH_ZYLONITE) ||\
defined(CONFIG_MACH_LITTLETON) ||\
defined(CONFIG_MACH_ZYLONITE2) ||\
defined(CONFIG_ARCH_VIPER) ||\
defined(CONFIG_MACH_STARGATE2)
#include <asm/mach-types.h>
/* Now the bus width is specified in the platform data
* pretend here to support all I/O access types
*/
#define SMC_CAN_USE_8BIT 1
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 1
#define SMC_NOWAIT 1
#define SMC_IO_SHIFT (lp->io_shift)
#define SMC_inb(a, r) readb((a) + (r))
#define SMC_inw(a, r) readw((a) + (r))
#define SMC_inl(a, r) readl((a) + (r))
#define SMC_outb(v, a, r) writeb(v, (a) + (r))
#define SMC_outl(v, a, r) writel(v, (a) + (r))
#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
#define SMC_IRQ_FLAGS (-1) /* from resource */
/* We actually can't write halfwords properly if not word aligned */
static inline void SMC_outw(u16 val, void __iomem *ioaddr, int reg)
{
if ((machine_is_mainstone() || machine_is_stargate2()) && reg & 2) {
unsigned int v = val << 16;
v |= readl(ioaddr + (reg & ~2)) & 0xffff;
writel(v, ioaddr + (reg & ~2));
} else {
writew(val, ioaddr + reg);
}
}
#elif defined(CONFIG_BLACKFIN)
#define SMC_IRQ_FLAGS IRQF_TRIGGER_HIGH
#define RPC_LSA_DEFAULT RPC_LED_100_10
#define RPC_LSB_DEFAULT RPC_LED_TX_RX
#define SMC_CAN_USE_8BIT 0
#define SMC_CAN_USE_16BIT 1
# if defined(CONFIG_BF561)
#define SMC_CAN_USE_32BIT 1
# else
#define SMC_CAN_USE_32BIT 0
# endif
#define SMC_IO_SHIFT 0
#define SMC_NOWAIT 1
#define SMC_USE_BFIN_DMA 0
#define SMC_inw(a, r) readw((a) + (r))
#define SMC_outw(v, a, r) writew(v, (a) + (r))
#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
# if SMC_CAN_USE_32BIT
#define SMC_inl(a, r) readl((a) + (r))
#define SMC_outl(v, a, r) writel(v, (a) + (r))
#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
# endif
#elif defined(CONFIG_REDWOOD_5) || defined(CONFIG_REDWOOD_6)
/* We can only do 16-bit reads and writes in the static memory space. */
#define SMC_CAN_USE_8BIT 0
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 0
#define SMC_NOWAIT 1
#define SMC_IO_SHIFT 0
#define SMC_inw(a, r) in_be16((volatile u16 *)((a) + (r)))
#define SMC_outw(v, a, r) out_be16((volatile u16 *)((a) + (r)), v)
#define SMC_insw(a, r, p, l) \
do { \
unsigned long __port = (a) + (r); \
u16 *__p = (u16 *)(p); \
int __l = (l); \
insw(__port, __p, __l); \
while (__l > 0) { \
*__p = swab16(*__p); \
__p++; \
__l--; \
} \
} while (0)
#define SMC_outsw(a, r, p, l) \
do { \
unsigned long __port = (a) + (r); \
u16 *__p = (u16 *)(p); \
int __l = (l); \
while (__l > 0) { \
/* Believe it or not, the swab isn't needed. */ \
outw( /* swab16 */ (*__p++), __port); \
__l--; \
} \
} while (0)
#define SMC_IRQ_FLAGS (0)
#elif defined(CONFIG_SA1100_PLEB)
/* We can only do 16-bit reads and writes in the static memory space. */
#define SMC_CAN_USE_8BIT 1
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 0
#define SMC_IO_SHIFT 0
#define SMC_NOWAIT 1
#define SMC_inb(a, r) readb((a) + (r))
#define SMC_insb(a, r, p, l) readsb((a) + (r), p, (l))
#define SMC_inw(a, r) readw((a) + (r))
#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
#define SMC_outb(v, a, r) writeb(v, (a) + (r))
#define SMC_outsb(a, r, p, l) writesb((a) + (r), p, (l))
#define SMC_outw(v, a, r) writew(v, (a) + (r))
#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
#define SMC_IRQ_FLAGS (-1)
#elif defined(CONFIG_SA1100_ASSABET)
#include <mach/neponset.h>
/* We can only do 8-bit reads and writes in the static memory space. */
#define SMC_CAN_USE_8BIT 1
#define SMC_CAN_USE_16BIT 0
#define SMC_CAN_USE_32BIT 0
#define SMC_NOWAIT 1
/* The first two address lines aren't connected... */
#define SMC_IO_SHIFT 2
#define SMC_inb(a, r) readb((a) + (r))
#define SMC_outb(v, a, r) writeb(v, (a) + (r))
#define SMC_insb(a, r, p, l) readsb((a) + (r), p, (l))
#define SMC_outsb(a, r, p, l) writesb((a) + (r), p, (l))
#define SMC_IRQ_FLAGS (-1) /* from resource */
#elif defined(CONFIG_MACH_LOGICPD_PXA270) \
|| defined(CONFIG_MACH_NOMADIK_8815NHK)
#define SMC_CAN_USE_8BIT 0
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 0
#define SMC_IO_SHIFT 0
#define SMC_NOWAIT 1
#define SMC_inw(a, r) readw((a) + (r))
#define SMC_outw(v, a, r) writew(v, (a) + (r))
#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
#elif defined(CONFIG_ARCH_INNOKOM) || \
defined(CONFIG_ARCH_PXA_IDP) || \
defined(CONFIG_ARCH_RAMSES) || \
defined(CONFIG_ARCH_PCM027)
#define SMC_CAN_USE_8BIT 1
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 1
#define SMC_IO_SHIFT 0
#define SMC_NOWAIT 1
#define SMC_USE_PXA_DMA 1
#define SMC_inb(a, r) readb((a) + (r))
#define SMC_inw(a, r) readw((a) + (r))
#define SMC_inl(a, r) readl((a) + (r))
#define SMC_outb(v, a, r) writeb(v, (a) + (r))
#define SMC_outl(v, a, r) writel(v, (a) + (r))
#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
#define SMC_IRQ_FLAGS (-1) /* from resource */
/* We actually can't write halfwords properly if not word aligned */
static inline void
SMC_outw(u16 val, void __iomem *ioaddr, int reg)
{
if (reg & 2) {
unsigned int v = val << 16;
v |= readl(ioaddr + (reg & ~2)) & 0xffff;
writel(v, ioaddr + (reg & ~2));
} else {
writew(val, ioaddr + reg);
}
}
#elif defined(CONFIG_ARCH_OMAP)
/* We can only do 16-bit reads and writes in the static memory space. */
#define SMC_CAN_USE_8BIT 0
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 0
#define SMC_IO_SHIFT 0
#define SMC_NOWAIT 1
#define SMC_inw(a, r) readw((a) + (r))
#define SMC_outw(v, a, r) writew(v, (a) + (r))
#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
#define SMC_IRQ_FLAGS (-1) /* from resource */
#elif defined(CONFIG_SH_SH4202_MICRODEV)
#define SMC_CAN_USE_8BIT 0
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 0
#define SMC_inb(a, r) inb((a) + (r) - 0xa0000000)
#define SMC_inw(a, r) inw((a) + (r) - 0xa0000000)
#define SMC_inl(a, r) inl((a) + (r) - 0xa0000000)
#define SMC_outb(v, a, r) outb(v, (a) + (r) - 0xa0000000)
#define SMC_outw(v, a, r) outw(v, (a) + (r) - 0xa0000000)
#define SMC_outl(v, a, r) outl(v, (a) + (r) - 0xa0000000)
#define SMC_insl(a, r, p, l) insl((a) + (r) - 0xa0000000, p, l)
#define SMC_outsl(a, r, p, l) outsl((a) + (r) - 0xa0000000, p, l)
#define SMC_insw(a, r, p, l) insw((a) + (r) - 0xa0000000, p, l)
#define SMC_outsw(a, r, p, l) outsw((a) + (r) - 0xa0000000, p, l)
#define SMC_IRQ_FLAGS (0)
#elif defined(CONFIG_M32R)
#define SMC_CAN_USE_8BIT 0
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 0
#define SMC_inb(a, r) inb(((u32)a) + (r))
#define SMC_inw(a, r) inw(((u32)a) + (r))
#define SMC_outb(v, a, r) outb(v, ((u32)a) + (r))
#define SMC_outw(v, a, r) outw(v, ((u32)a) + (r))
#define SMC_insw(a, r, p, l) insw(((u32)a) + (r), p, l)
#define SMC_outsw(a, r, p, l) outsw(((u32)a) + (r), p, l)
#define SMC_IRQ_FLAGS (0)
#define RPC_LSA_DEFAULT RPC_LED_TX_RX
#define RPC_LSB_DEFAULT RPC_LED_100_10
#elif defined(CONFIG_MACH_LPD79520) \
|| defined(CONFIG_MACH_LPD7A400) \
|| defined(CONFIG_MACH_LPD7A404)
/* The LPD7X_IOBARRIER is necessary to overcome a mismatch between the
* way that the CPU handles chip selects and the way that the SMC chip
* expects the chip select to operate. Refer to
* Documentation/arm/Sharp-LH/IOBarrier for details. The read from
* IOBARRIER is a byte, in order that we read the least-common
* denominator. It would be wasteful to read 32 bits from an 8-bit
* accessible region.
*
* There is no explicit protection against interrupts intervening
* between the writew and the IOBARRIER. In SMC ISR there is a
* preamble that performs an IOBARRIER in the extremely unlikely event
* that the driver interrupts itself between a writew to the chip an
* the IOBARRIER that follows *and* the cache is large enough that the
* first off-chip access while handing the interrupt is to the SMC
* chip. Other devices in the same address space as the SMC chip must
* be aware of the potential for trouble and perform a similar
* IOBARRIER on entry to their ISR.
*/
#include <mach/constants.h> /* IOBARRIER_VIRT */
#define SMC_CAN_USE_8BIT 0
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 0
#define SMC_NOWAIT 0
#define LPD7X_IOBARRIER readb (IOBARRIER_VIRT)
#define SMC_inw(a,r)\
({ unsigned short v = readw ((void*) ((a) + (r))); LPD7X_IOBARRIER; v; })
#define SMC_outw(v,a,r) ({ writew ((v), (a) + (r)); LPD7X_IOBARRIER; })
#define SMC_insw LPD7_SMC_insw
static inline void LPD7_SMC_insw (unsigned char* a, int r,
unsigned char* p, int l)
{
unsigned short* ps = (unsigned short*) p;
while (l-- > 0) {
*ps++ = readw (a + r);
LPD7X_IOBARRIER;
}
}
#define SMC_outsw LPD7_SMC_outsw
static inline void LPD7_SMC_outsw (unsigned char* a, int r,
unsigned char* p, int l)
{
unsigned short* ps = (unsigned short*) p;
while (l-- > 0) {
writew (*ps++, a + r);
LPD7X_IOBARRIER;
}
}
#define SMC_INTERRUPT_PREAMBLE LPD7X_IOBARRIER
#define RPC_LSA_DEFAULT RPC_LED_TX_RX
#define RPC_LSB_DEFAULT RPC_LED_100_10
#elif defined(CONFIG_ARCH_VERSATILE)
#define SMC_CAN_USE_8BIT 1
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 1
#define SMC_NOWAIT 1
#define SMC_inb(a, r) readb((a) + (r))
#define SMC_inw(a, r) readw((a) + (r))
#define SMC_inl(a, r) readl((a) + (r))
#define SMC_outb(v, a, r) writeb(v, (a) + (r))
#define SMC_outw(v, a, r) writew(v, (a) + (r))
#define SMC_outl(v, a, r) writel(v, (a) + (r))
#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
#define SMC_IRQ_FLAGS (-1) /* from resource */
#elif defined(CONFIG_MN10300)
/*
* MN10300/AM33 configuration
*/
#include <unit/smc91111.h>
#else
/*
* Default configuration
*/
#define SMC_CAN_USE_8BIT 1
#define SMC_CAN_USE_16BIT 1
#define SMC_CAN_USE_32BIT 1
#define SMC_NOWAIT 1
#define SMC_IO_SHIFT (lp->io_shift)
#define SMC_inb(a, r) readb((a) + (r))
#define SMC_inw(a, r) readw((a) + (r))
#define SMC_inl(a, r) readl((a) + (r))
#define SMC_outb(v, a, r) writeb(v, (a) + (r))
#define SMC_outw(v, a, r) writew(v, (a) + (r))
#define SMC_outl(v, a, r) writel(v, (a) + (r))
#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
#define RPC_LSA_DEFAULT RPC_LED_100_10
#define RPC_LSB_DEFAULT RPC_LED_TX_RX
#endif
/* store this information for the driver.. */
struct smc_local {
/*
* If I have to wait until memory is available to send a
* packet, I will store the skbuff here, until I get the
* desired memory. Then, I'll send it out and free it.
*/
struct sk_buff *pending_tx_skb;
struct tasklet_struct tx_task;
/* version/revision of the SMC91x chip */
int version;
/* Contains the current active transmission mode */
int tcr_cur_mode;
/* Contains the current active receive mode */
int rcr_cur_mode;
/* Contains the current active receive/phy mode */
int rpc_cur_mode;
int ctl_rfduplx;
int ctl_rspeed;
u32 msg_enable;
u32 phy_type;
struct mii_if_info mii;
/* work queue */
struct work_struct phy_configure;
struct net_device *dev;
int work_pending;
spinlock_t lock;
#ifdef CONFIG_ARCH_PXA
/* DMA needs the physical address of the chip */
u_long physaddr;
struct device *device;
#endif
void __iomem *base;
void __iomem *datacs;
/* the low address lines on some platforms aren't connected... */
int io_shift;
struct smc91x_platdata cfg;
};
#define SMC_8BIT(p) ((p)->cfg.flags & SMC91X_USE_8BIT)
#define SMC_16BIT(p) ((p)->cfg.flags & SMC91X_USE_16BIT)
#define SMC_32BIT(p) ((p)->cfg.flags & SMC91X_USE_32BIT)
#ifdef CONFIG_ARCH_PXA
/*
* Let's use the DMA engine on the XScale PXA2xx for RX packets. This is
* always happening in irq context so no need to worry about races. TX is
* different and probably not worth it for that reason, and not as critical
* as RX which can overrun memory and lose packets.
*/
#include <linux/dma-mapping.h>
#include <mach/dma.h>
#ifdef SMC_insl
#undef SMC_insl
#define SMC_insl(a, r, p, l) \
smc_pxa_dma_insl(a, lp, r, dev->dma, p, l)
static inline void
smc_pxa_dma_insl(void __iomem *ioaddr, struct smc_local *lp, int reg, int dma,
u_char *buf, int len)
{
u_long physaddr = lp->physaddr;
dma_addr_t dmabuf;
/* fallback if no DMA available */
if (dma == (unsigned char)-1) {
readsl(ioaddr + reg, buf, len);
return;
}
/* 64 bit alignment is required for memory to memory DMA */
if ((long)buf & 4) {
*((u32 *)buf) = SMC_inl(ioaddr, reg);
buf += 4;
len--;
}
len *= 4;
dmabuf = dma_map_single(lp->device, buf, len, DMA_FROM_DEVICE);
DCSR(dma) = DCSR_NODESC;
DTADR(dma) = dmabuf;
DSADR(dma) = physaddr + reg;
DCMD(dma) = (DCMD_INCTRGADDR | DCMD_BURST32 |
DCMD_WIDTH4 | (DCMD_LENGTH & len));
DCSR(dma) = DCSR_NODESC | DCSR_RUN;
while (!(DCSR(dma) & DCSR_STOPSTATE))
cpu_relax();
DCSR(dma) = 0;
dma_unmap_single(lp->device, dmabuf, len, DMA_FROM_DEVICE);
}
#endif
#ifdef SMC_insw
#undef SMC_insw
#define SMC_insw(a, r, p, l) \
smc_pxa_dma_insw(a, lp, r, dev->dma, p, l)
static inline void
smc_pxa_dma_insw(void __iomem *ioaddr, struct smc_local *lp, int reg, int dma,
u_char *buf, int len)
{
u_long physaddr = lp->physaddr;
dma_addr_t dmabuf;
/* fallback if no DMA available */
if (dma == (unsigned char)-1) {
readsw(ioaddr + reg, buf, len);
return;
}
/* 64 bit alignment is required for memory to memory DMA */
while ((long)buf & 6) {
*((u16 *)buf) = SMC_inw(ioaddr, reg);
buf += 2;
len--;
}
len *= 2;
dmabuf = dma_map_single(lp->device, buf, len, DMA_FROM_DEVICE);
DCSR(dma) = DCSR_NODESC;
DTADR(dma) = dmabuf;
DSADR(dma) = physaddr + reg;
DCMD(dma) = (DCMD_INCTRGADDR | DCMD_BURST32 |
DCMD_WIDTH2 | (DCMD_LENGTH & len));
DCSR(dma) = DCSR_NODESC | DCSR_RUN;
while (!(DCSR(dma) & DCSR_STOPSTATE))
cpu_relax();
DCSR(dma) = 0;
dma_unmap_single(lp->device, dmabuf, len, DMA_FROM_DEVICE);
}
#endif
static void
smc_pxa_dma_irq(int dma, void *dummy)
{
DCSR(dma) = 0;
}
#endif /* CONFIG_ARCH_PXA */
/*
* Everything a particular hardware setup needs should have been defined
* at this point. Add stubs for the undefined cases, mainly to avoid
* compilation warnings since they'll be optimized away, or to prevent buggy
* use of them.
*/
#if ! SMC_CAN_USE_32BIT
#define SMC_inl(ioaddr, reg) ({ BUG(); 0; })
#define SMC_outl(x, ioaddr, reg) BUG()
#define SMC_insl(a, r, p, l) BUG()
#define SMC_outsl(a, r, p, l) BUG()
#endif
#if !defined(SMC_insl) || !defined(SMC_outsl)
#define SMC_insl(a, r, p, l) BUG()
#define SMC_outsl(a, r, p, l) BUG()
#endif
#if ! SMC_CAN_USE_16BIT
/*
* Any 16-bit access is performed with two 8-bit accesses if the hardware
* can't do it directly. Most registers are 16-bit so those are mandatory.
*/
#define SMC_outw(x, ioaddr, reg) \
do { \
unsigned int __val16 = (x); \
SMC_outb( __val16, ioaddr, reg ); \
SMC_outb( __val16 >> 8, ioaddr, reg + (1 << SMC_IO_SHIFT));\
} while (0)
#define SMC_inw(ioaddr, reg) \
({ \
unsigned int __val16; \
__val16 = SMC_inb( ioaddr, reg ); \
__val16 |= SMC_inb( ioaddr, reg + (1 << SMC_IO_SHIFT)) << 8; \
__val16; \
})
#define SMC_insw(a, r, p, l) BUG()
#define SMC_outsw(a, r, p, l) BUG()
#endif
#if !defined(SMC_insw) || !defined(SMC_outsw)
#define SMC_insw(a, r, p, l) BUG()
#define SMC_outsw(a, r, p, l) BUG()
#endif
#if ! SMC_CAN_USE_8BIT
#define SMC_inb(ioaddr, reg) ({ BUG(); 0; })
#define SMC_outb(x, ioaddr, reg) BUG()
#define SMC_insb(a, r, p, l) BUG()
#define SMC_outsb(a, r, p, l) BUG()
#endif
#if !defined(SMC_insb) || !defined(SMC_outsb)
#define SMC_insb(a, r, p, l) BUG()
#define SMC_outsb(a, r, p, l) BUG()
#endif
#ifndef SMC_CAN_USE_DATACS
#define SMC_CAN_USE_DATACS 0
#endif
#ifndef SMC_IO_SHIFT
#define SMC_IO_SHIFT 0
#endif
#ifndef SMC_IRQ_FLAGS
#define SMC_IRQ_FLAGS IRQF_TRIGGER_RISING
#endif
#ifndef SMC_INTERRUPT_PREAMBLE
#define SMC_INTERRUPT_PREAMBLE
#endif
/* Because of bank switching, the LAN91x uses only 16 I/O ports */
#define SMC_IO_EXTENT (16 << SMC_IO_SHIFT)
#define SMC_DATA_EXTENT (4)
/*
. Bank Select Register:
.
. yyyy yyyy 0000 00xx
. xx = bank number
. yyyy yyyy = 0x33, for identification purposes.
*/
#define BANK_SELECT (14 << SMC_IO_SHIFT)
// Transmit Control Register
/* BANK 0 */
#define TCR_REG(lp) SMC_REG(lp, 0x0000, 0)
#define TCR_ENABLE 0x0001 // When 1 we can transmit
#define TCR_LOOP 0x0002 // Controls output pin LBK
#define TCR_FORCOL 0x0004 // When 1 will force a collision
#define TCR_PAD_EN 0x0080 // When 1 will pad tx frames < 64 bytes w/0
#define TCR_NOCRC 0x0100 // When 1 will not append CRC to tx frames
#define TCR_MON_CSN 0x0400 // When 1 tx monitors carrier
#define TCR_FDUPLX 0x0800 // When 1 enables full duplex operation
#define TCR_STP_SQET 0x1000 // When 1 stops tx if Signal Quality Error
#define TCR_EPH_LOOP 0x2000 // When 1 enables EPH block loopback
#define TCR_SWFDUP 0x8000 // When 1 enables Switched Full Duplex mode
#define TCR_CLEAR 0 /* do NOTHING */
/* the default settings for the TCR register : */
#define TCR_DEFAULT (TCR_ENABLE | TCR_PAD_EN)
// EPH Status Register
/* BANK 0 */
#define EPH_STATUS_REG(lp) SMC_REG(lp, 0x0002, 0)
#define ES_TX_SUC 0x0001 // Last TX was successful
#define ES_SNGL_COL 0x0002 // Single collision detected for last tx
#define ES_MUL_COL 0x0004 // Multiple collisions detected for last tx
#define ES_LTX_MULT 0x0008 // Last tx was a multicast
#define ES_16COL 0x0010 // 16 Collisions Reached
#define ES_SQET 0x0020 // Signal Quality Error Test
#define ES_LTXBRD 0x0040 // Last tx was a broadcast
#define ES_TXDEFR 0x0080 // Transmit Deferred
#define ES_LATCOL 0x0200 // Late collision detected on last tx
#define ES_LOSTCARR 0x0400 // Lost Carrier Sense
#define ES_EXC_DEF 0x0800 // Excessive Deferral
#define ES_CTR_ROL 0x1000 // Counter Roll Over indication
#define ES_LINK_OK 0x4000 // Driven by inverted value of nLNK pin
#define ES_TXUNRN 0x8000 // Tx Underrun
// Receive Control Register
/* BANK 0 */
#define RCR_REG(lp) SMC_REG(lp, 0x0004, 0)
#define RCR_RX_ABORT 0x0001 // Set if a rx frame was aborted
#define RCR_PRMS 0x0002 // Enable promiscuous mode
#define RCR_ALMUL 0x0004 // When set accepts all multicast frames
#define RCR_RXEN 0x0100 // IFF this is set, we can receive packets
#define RCR_STRIP_CRC 0x0200 // When set strips CRC from rx packets
#define RCR_ABORT_ENB 0x0200 // When set will abort rx on collision
#define RCR_FILT_CAR 0x0400 // When set filters leading 12 bit s of carrier
#define RCR_SOFTRST 0x8000 // resets the chip
/* the normal settings for the RCR register : */
#define RCR_DEFAULT (RCR_STRIP_CRC | RCR_RXEN)
#define RCR_CLEAR 0x0 // set it to a base state
// Counter Register
/* BANK 0 */
#define COUNTER_REG(lp) SMC_REG(lp, 0x0006, 0)
// Memory Information Register
/* BANK 0 */
#define MIR_REG(lp) SMC_REG(lp, 0x0008, 0)
// Receive/Phy Control Register
/* BANK 0 */
#define RPC_REG(lp) SMC_REG(lp, 0x000A, 0)
#define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode.
#define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode
#define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode
#define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb
#define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb
#ifndef RPC_LSA_DEFAULT
#define RPC_LSA_DEFAULT RPC_LED_100
#endif
#ifndef RPC_LSB_DEFAULT
#define RPC_LSB_DEFAULT RPC_LED_FD
#endif
#define RPC_DEFAULT (RPC_ANEG | RPC_SPEED | RPC_DPLX)
/* Bank 0 0x0C is reserved */
// Bank Select Register
/* All Banks */
#define BSR_REG 0x000E
// Configuration Reg
/* BANK 1 */
#define CONFIG_REG(lp) SMC_REG(lp, 0x0000, 1)
#define CONFIG_EXT_PHY 0x0200 // 1=external MII, 0=internal Phy
#define CONFIG_GPCNTRL 0x0400 // Inverse value drives pin nCNTRL
#define CONFIG_NO_WAIT 0x1000 // When 1 no extra wait states on ISA bus
#define CONFIG_EPH_POWER_EN 0x8000 // When 0 EPH is placed into low power mode.
// Default is powered-up, Internal Phy, Wait States, and pin nCNTRL=low
#define CONFIG_DEFAULT (CONFIG_EPH_POWER_EN)
// Base Address Register
/* BANK 1 */
#define BASE_REG(lp) SMC_REG(lp, 0x0002, 1)
// Individual Address Registers
/* BANK 1 */
#define ADDR0_REG(lp) SMC_REG(lp, 0x0004, 1)
#define ADDR1_REG(lp) SMC_REG(lp, 0x0006, 1)
#define ADDR2_REG(lp) SMC_REG(lp, 0x0008, 1)
// General Purpose Register
/* BANK 1 */
#define GP_REG(lp) SMC_REG(lp, 0x000A, 1)
// Control Register
/* BANK 1 */
#define CTL_REG(lp) SMC_REG(lp, 0x000C, 1)
#define CTL_RCV_BAD 0x4000 // When 1 bad CRC packets are received
#define CTL_AUTO_RELEASE 0x0800 // When 1 tx pages are released automatically
#define CTL_LE_ENABLE 0x0080 // When 1 enables Link Error interrupt
#define CTL_CR_ENABLE 0x0040 // When 1 enables Counter Rollover interrupt
#define CTL_TE_ENABLE 0x0020 // When 1 enables Transmit Error interrupt
#define CTL_EEPROM_SELECT 0x0004 // Controls EEPROM reload & store
#define CTL_RELOAD 0x0002 // When set reads EEPROM into registers
#define CTL_STORE 0x0001 // When set stores registers into EEPROM
// MMU Command Register
/* BANK 2 */
#define MMU_CMD_REG(lp) SMC_REG(lp, 0x0000, 2)
#define MC_BUSY 1 // When 1 the last release has not completed
#define MC_NOP (0<<5) // No Op
#define MC_ALLOC (1<<5) // OR with number of 256 byte packets
#define MC_RESET (2<<5) // Reset MMU to initial state
#define MC_REMOVE (3<<5) // Remove the current rx packet
#define MC_RELEASE (4<<5) // Remove and release the current rx packet
#define MC_FREEPKT (5<<5) // Release packet in PNR register
#define MC_ENQUEUE (6<<5) // Enqueue the packet for transmit
#define MC_RSTTXFIFO (7<<5) // Reset the TX FIFOs
// Packet Number Register
/* BANK 2 */
#define PN_REG(lp) SMC_REG(lp, 0x0002, 2)
// Allocation Result Register
/* BANK 2 */
#define AR_REG(lp) SMC_REG(lp, 0x0003, 2)
#define AR_FAILED 0x80 // Alocation Failed
// TX FIFO Ports Register
/* BANK 2 */
#define TXFIFO_REG(lp) SMC_REG(lp, 0x0004, 2)
#define TXFIFO_TEMPTY 0x80 // TX FIFO Empty
// RX FIFO Ports Register
/* BANK 2 */
#define RXFIFO_REG(lp) SMC_REG(lp, 0x0005, 2)
#define RXFIFO_REMPTY 0x80 // RX FIFO Empty
#define FIFO_REG(lp) SMC_REG(lp, 0x0004, 2)
// Pointer Register
/* BANK 2 */
#define PTR_REG(lp) SMC_REG(lp, 0x0006, 2)
#define PTR_RCV 0x8000 // 1=Receive area, 0=Transmit area
#define PTR_AUTOINC 0x4000 // Auto increment the pointer on each access
#define PTR_READ 0x2000 // When 1 the operation is a read
// Data Register
/* BANK 2 */
#define DATA_REG(lp) SMC_REG(lp, 0x0008, 2)
// Interrupt Status/Acknowledge Register
/* BANK 2 */
#define INT_REG(lp) SMC_REG(lp, 0x000C, 2)
// Interrupt Mask Register
/* BANK 2 */
#define IM_REG(lp) SMC_REG(lp, 0x000D, 2)
#define IM_MDINT 0x80 // PHY MI Register 18 Interrupt
#define IM_ERCV_INT 0x40 // Early Receive Interrupt
#define IM_EPH_INT 0x20 // Set by Ethernet Protocol Handler section
#define IM_RX_OVRN_INT 0x10 // Set by Receiver Overruns
#define IM_ALLOC_INT 0x08 // Set when allocation request is completed
#define IM_TX_EMPTY_INT 0x04 // Set if the TX FIFO goes empty
#define IM_TX_INT 0x02 // Transmit Interrupt
#define IM_RCV_INT 0x01 // Receive Interrupt
// Multicast Table Registers
/* BANK 3 */
#define MCAST_REG1(lp) SMC_REG(lp, 0x0000, 3)
#define MCAST_REG2(lp) SMC_REG(lp, 0x0002, 3)
#define MCAST_REG3(lp) SMC_REG(lp, 0x0004, 3)
#define MCAST_REG4(lp) SMC_REG(lp, 0x0006, 3)
// Management Interface Register (MII)
/* BANK 3 */
#define MII_REG(lp) SMC_REG(lp, 0x0008, 3)
#define MII_MSK_CRS100 0x4000 // Disables CRS100 detection during tx half dup
#define MII_MDOE 0x0008 // MII Output Enable
#define MII_MCLK 0x0004 // MII Clock, pin MDCLK
#define MII_MDI 0x0002 // MII Input, pin MDI
#define MII_MDO 0x0001 // MII Output, pin MDO
// Revision Register
/* BANK 3 */
/* ( hi: chip id low: rev # ) */
#define REV_REG(lp) SMC_REG(lp, 0x000A, 3)
// Early RCV Register
/* BANK 3 */
/* this is NOT on SMC9192 */
#define ERCV_REG(lp) SMC_REG(lp, 0x000C, 3)
#define ERCV_RCV_DISCRD 0x0080 // When 1 discards a packet being received
#define ERCV_THRESHOLD 0x001F // ERCV Threshold Mask
// External Register
/* BANK 7 */
#define EXT_REG(lp) SMC_REG(lp, 0x0000, 7)
#define CHIP_9192 3
#define CHIP_9194 4
#define CHIP_9195 5
#define CHIP_9196 6
#define CHIP_91100 7
#define CHIP_91100FD 8
#define CHIP_91111FD 9
static const char * chip_ids[ 16 ] = {
NULL, NULL, NULL,
/* 3 */ "SMC91C90/91C92",
/* 4 */ "SMC91C94",
/* 5 */ "SMC91C95",
/* 6 */ "SMC91C96",
/* 7 */ "SMC91C100",
/* 8 */ "SMC91C100FD",
/* 9 */ "SMC91C11xFD",
NULL, NULL, NULL,
NULL, NULL, NULL};
/*
. Receive status bits
*/
#define RS_ALGNERR 0x8000
#define RS_BRODCAST 0x4000
#define RS_BADCRC 0x2000
#define RS_ODDFRAME 0x1000
#define RS_TOOLONG 0x0800
#define RS_TOOSHORT 0x0400
#define RS_MULTICAST 0x0001
#define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT)
/*
* PHY IDs
* LAN83C183 == LAN91C111 Internal PHY
*/
#define PHY_LAN83C183 0x0016f840
#define PHY_LAN83C180 0x02821c50
/*
* PHY Register Addresses (LAN91C111 Internal PHY)
*
* Generic PHY registers can be found in <linux/mii.h>
*
* These phy registers are specific to our on-board phy.
*/
// PHY Configuration Register 1
#define PHY_CFG1_REG 0x10
#define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled
#define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled
#define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down
#define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler
#define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable
#define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled
#define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm)
#define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
#define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust
#define PHY_CFG1_TLVL_MASK 0x003C
#define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time
// PHY Configuration Register 2
#define PHY_CFG2_REG 0x11
#define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled
#define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled
#define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt)
#define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo
// PHY Status Output (and Interrupt status) Register
#define PHY_INT_REG 0x12 // Status Output (Interrupt Status)
#define PHY_INT_INT 0x8000 // 1=bits have changed since last read
#define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected
#define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync
#define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx
#define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx
#define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx
#define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected
#define PHY_INT_JAB 0x0100 // 1=Jabber detected
#define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode
#define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex
// PHY Interrupt/Status Mask Register
#define PHY_MASK_REG 0x13 // Interrupt Mask
// Uses the same bit definitions as PHY_INT_REG
/*
* SMC91C96 ethernet config and status registers.
* These are in the "attribute" space.
*/
#define ECOR 0x8000
#define ECOR_RESET 0x80
#define ECOR_LEVEL_IRQ 0x40
#define ECOR_WR_ATTRIB 0x04
#define ECOR_ENABLE 0x01
#define ECSR 0x8002
#define ECSR_IOIS8 0x20
#define ECSR_PWRDWN 0x04
#define ECSR_INT 0x02
#define ATTRIB_SIZE ((64*1024) << SMC_IO_SHIFT)
/*
* Macros to abstract register access according to the data bus
* capabilities. Please use those and not the in/out primitives.
* Note: the following macros do *not* select the bank -- this must
* be done separately as needed in the main code. The SMC_REG() macro
* only uses the bank argument for debugging purposes (when enabled).
*
* Note: despite inline functions being safer, everything leading to this
* should preferably be macros to let BUG() display the line number in