forked from apollo-ng/picoReflow
/
config.py.EXAMPLE
88 lines (66 loc) · 2.73 KB
/
config.py.EXAMPLE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
import logging
########################################################################
#
# General options
### Logging
log_level = logging.INFO
log_format = '%(asctime)s %(levelname)s %(name)s: %(message)s'
### Server
listening_ip = "0.0.0.0"
listening_port = 8081
### Cost Estimate
kwh_rate = 0.26 # Rate in currency_type to calculate cost to run job
currency_type = "EUR" # Currency Symbol to show when calculating cost to run job
########################################################################
#
# GPIO Setup (BCM SoC Numbering Schema)
#
# Check the RasPi docs to see where these GPIOs are
# connected on the P1 header for your board type/rev.
# These were tested on a Pi B Rev2 but of course you
# can use whichever GPIO you prefer/have available.
### Outputs
gpio_heat = 11 # Switches zero-cross solid-state-relay
gpio_cool = 10 # Regulates PWM for 12V DC Blower
gpio_air = 9 # Switches 0-phase det. solid-state-relay
heater_invert = 0 # switches the polarity of the heater control
### Inputs
gpio_door = 18
### Thermocouple Adapter selection:
# max31855 - bitbang SPI interface
# max31855spi - kernel SPI interface
# max6675 - bitbang SPI interface
max31855 = 1
max6675 = 0
max31855spi = 0 # if you use this one, you MUST reassign the default GPIO pins
### Thermocouple Connection (using bitbang interfaces)
gpio_sensor_cs = 27
gpio_sensor_clock = 22
gpio_sensor_data = 17
### Thermocouple SPI Connection (using adafrut drivers + kernel SPI interface)
spi_sensor_chip_id = 0
### amount of time, in seconds, to wait between reads of the thermocouple
sensor_time_wait = .5
########################################################################
#
# PID parameters
pid_ki = 0.1 # Integration
pid_kd = 0.4 # Derivative
pid_kp = 0.5 # Proportional
########################################################################
#
# Simulation parameters
sim_t_env = 25.0 # deg C
sim_c_heat = 100.0 # J/K heat capacity of heat element
sim_c_oven = 2000.0 # J/K heat capacity of oven
sim_p_heat = 3500.0 # W heating power of oven
sim_R_o_nocool = 1.0 # K/W thermal resistance oven -> environment
sim_R_o_cool = 0.05 # K/W " with cooling
sim_R_ho_noair = 0.1 # K/W thermal resistance heat element -> oven
sim_R_ho_air = 0.05 # K/W " with internal air circulation
########################################################################
#
# Time and Temperature parameters
temp_scale = "c" # c = Celsius | f = Fahrenheit - Unit to display
time_scale_slope = "s" # s = Seconds | m = Minutes | h = Hours - Slope displayed in temp_scale per time_scale_slope
time_scale_profile = "s" # s = Seconds | m = Minutes | h = Hours - Enter and view target time in time_scale_profile