#start-many Setup Guide
There are many ways to setup a wallet to support start-many. This guide will walk through two of them.
- Importing an existing wallet (recommended if you are consolidating wallets).
- Sending 10,000 Erotica to new wallet addresses.
This is the way to go if you are consolidating multiple wallets into one that supports start-many.
Open your QT Wallet and go to console (from the menu select Tools => Debug Console)
Dump the private key from your MasterNode's pulic key.
walletpassphrase [your_wallet_passphrase] 600
dumpprivkey [mn_public_key]
Copy the resulting priviate key. You'll use it in the next step.
Open your QT Wallet and go to console (from the menu select Tools => Debug Console)
Import the private key from the step above.
walletpassphrase [your_wallet_passphrase] 600
importprivkey [single_instance_private_key]
The wallet will re-scan and you will see your available balance increase by the amount that was in the imported wallet.
Skip Option 2. and go to Create masternode.conf file
If you used Option 1 above, then you can skip down to Create masternode.conf file.
- Open the QT Wallet.
- Click the Receive tab.
- Fill in the form to request a payment.
- Label: mn01
- Amount: 1000 (optional)
- Click Request payment
- Click the Copy Address button
Create a new wallet address for each MasterNode.
Close your QT Wallet.
Just like setting up a standard MN. Send exactly 10,000 Erotica to each new address created above.
Open your QT Wallet and go to console (from the menu select Tools => Debug Console)
Issue the following:
masternode genkey
Note: A masternode private key will need to be created for each MasterNode you run. You should not use the same masternode private key for multiple MasterNodes.
Close your QT Wallet.
Remember... this is local. Make sure your QT is not running.
Create the masternode.conf file in the same directory as your wallet.dat.
Copy the masternode private key and correspondig collateral output transaction that holds the 1K Erotica.
The masternode private key may be an existing key from Option 1, or a newly generated key from Option 2.
Please note, the masternode priviate key is not the same as a wallet private key. Never put your wallet private key in the masternode.conf file. That is equivalent to putting your 10,000 Erotica on the remote server and defeats the purpose of a hot/cold setup.
Open your QT Wallet and go to console (from the menu select Tools => Debug Console)
Issue the following:
masternode outputs
Make note of the hash (which is your collaterla_output) and index.
The new masternode.conf format consists of a space seperated text file. Each line consisting of an alias, IP address followed by port, masternode private key, collateral output transaction id and collateral output index, donation address and donation percentage (the latter two are optional and should be in format "address:percentage").
alias ipaddress:port masternode_private_key collateral_output collateral_output_index donationin_address:donation_percentage
Example:
mn01 127.0.0.1:6969 93HaYBVUCYjEMeeH1Y4sBGLALQZE1Yc1K64xiqgX37tGBDQL8Xg 2bcd3c84c84f87eaa86e4e56834c92927a07f9e18718810b92e0d0324456a67c 0
mn02 127.0.0.2:6969 93WaAb3htPJEV8E9aQcN23Jt97bPex7YvWfgMDTUdWJvzmrMqey aa9f1034d973377a5e733272c3d0eced1de22555ad45d6b24abadff8087948d4 0 7gnwGHt17heGpG9Crfeh4KGpYNFugPhJdh:25
If you are using a masternode.conf file you no longer need the erotica.conf file. The exception is if you need custom settings (thanks oblox).
If you generated a new masternode private key, you will need to update the remote erotica.conf files.
Shut down the daemon and then edit the file.
sudo nano .erotica/erotica.conf
If you generated a new masternode private key, you will need to update the masternodeprivkey value in your remote erotica.conf file.
If your remote server is not running, start your remote daemon as you normally would.
I usually confirm that remote is on the correct block by issuing:
eroticad getinfo
And compare with the official explorer at http://eroticacoin.com
Finally... time to start from local.
From the menu select Tools => Debug Console
If you want to review your masternode.conf setting before starting the MasterNodes, issue the following in the Debug Console:
masternode list-conf
Give it the eye-ball test. If satisfied, you can start your nodes one of two ways.
- masternode start-alias [alias_from_masternode.conf]. Example
masternode start-alias mn01
- masternode start-many