-
Notifications
You must be signed in to change notification settings - Fork 0
/
AA_PLANTILLA_CODE.asm
59 lines (50 loc) · 3.04 KB
/
AA_PLANTILLA_CODE.asm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
#INCLUDE <P18F4550.INC>
; CONFIG1L
CONFIG PLLDIV = 1 ; PLL Prescaler Selection bits (No prescale (4 MHz oscillator input drives PLL directly))
CONFIG CPUDIV = OSC1_PLL2 ; System Clock Postscaler Selection bits ([Primary Oscillator Src: /1][96 MHz PLL Src: /2])
CONFIG USBDIV = 1 ; USB Clock Selection bit (used in Full-Speed USB mode only; UCFG:FSEN = 1) (USB clock source comes directly from the primary oscillator block with no postscale)
; CONFIG1H
CONFIG FOSC = HS ; Oscillator Selection bits (HS oscillator (HS))
CONFIG FCMEN = OFF ; Fail-Safe Clock Monitor Enable bit (Fail-Safe Clock Monitor disabled)
CONFIG IESO = OFF ; Internal/External Oscillator Switchover bit (Oscillator Switchover mode disabled)
; CONFIG2L
CONFIG PWRT = OFF ; Power-up Timer Enable bit (PWRT disabled)
CONFIG BOR = ON ; Brown-out Reset Enable bits (Brown-out Reset enabled in hardware only (SBOREN is disabled))
CONFIG BORV = 3 ; Brown-out Reset Voltage bits (Minimum setting 2.05V)
CONFIG VREGEN = OFF ; USB Voltage Regulator Enable bit (USB voltage regulator disabled)
; CONFIG2H
CONFIG WDT = OFF ; Watchdog Timer Enable bit (WDT disabled (control is placed on the SWDTEN bit))
CONFIG WDTPS = 32768 ; Watchdog Timer Postscale Select bits (1:32768)
; CONFIG3H
CONFIG CCP2MX = OFF ; CCP2 MUX bit (CCP2 input/output is multiplexed with RB3)
CONFIG PBADEN = OFF ; PORTB A/D Enable bit (PORTB<4:0> pins are configured as digital I/O on Reset)
CONFIG LPT1OSC = OFF ; Low-Power Timer 1 Oscillator Enable bit (Timer1 configured for higher power operation)
CONFIG MCLRE = ON ; MCLR Pin Enable bit (MCLR pin enabled; RE3 input pin disabled)
;***************** PLANTILLA DE CÓDIGO VACIO *********************
;********** RESOLUCIÓN ****************
CBLOCK 0x00
variablePrueba; Mantenemos nuestra variable para las pruebas
varSuma ;Creamos una variable de suma
ENDC
ORG 0X000
GOTO MAIN;Creamos un alias para la posicion 0x000 de la memoria de programa
;Esto nos redirige al MAIN, y es a donde apunta el PC cuando se reinicia el microcontrolador
ORG 0X008
GOTO INT_ALTA_PRIOR; Añadimos el alias de la rutina de servicio para la interrupcion de alta prioridad
; Esto sucede en la posición 0x008 del PC
ORG 0X018
GOTO INT_BAJA_PRIOR; Hacemos lo mismo para el de baja prioridad
ORG 0X020
MAIN: ; Damos un alias de MAIN a la posicion 0X020 para el PC
;dentro de esta parte podemos configurar nuestros puertos de trabajo demás cosas
START:; Damos otro alías a otra posición de memoria de programa para iniciar
; la rutina que deseamos
ORG 0X0C0
INT_ALTA_PRIOR: ; Damos el alias de INT_ALTA_PRIOR
; a la posicion 0X0C0 para que acá vaya una rutina de servicio a la interrupción
; todo ello se verá más adelante
RETFIE ; usamos el retorno de interrupcion
ORG 0X0F0
INT_BAJA_PRIOR: ; Hacemos lo mismo para la de baja prioridad
RETFIE
END