-
Notifications
You must be signed in to change notification settings - Fork 4
/
Ads1015.cpp
190 lines (162 loc) · 8.01 KB
/
Ads1015.cpp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
#include "Ads1015.h"
#include <Wire.h>
#define ADS_I2C_ADDRESS 0x48
/*=========================================================================
CONVERSION DELAY (in mS)
-----------------------------------------------------------------------*/
//#define ADS1015_CONVERSIONDELAY (1)
#define ADS1115_CONVERSIONDELAY (8)
/*=========================================================================*/
/*=========================================================================
POINTER REGISTER
-----------------------------------------------------------------------*/
#define ADS1015_REG_POINTER_MASK (0x03)
#define ADS1015_REG_POINTER_CONVERT (0x00)
#define ADS1015_REG_POINTER_CONFIG (0x01)
#define ADS1015_REG_POINTER_LOWTHRESH (0x02)
#define ADS1015_REG_POINTER_HITHRESH (0x03)
/*=========================================================================*/
/*=========================================================================
CONFIG REGISTER
-----------------------------------------------------------------------*/
#define ADS1015_REG_CONFIG_OS_MASK (0x8000)
#define ADS1015_REG_CONFIG_OS_SINGLE (0x8000) // Write: Set to start a single-conversion
#define ADS1015_REG_CONFIG_OS_BUSY (0x0000) // Read: Bit = 0 when conversion is in progress
#define ADS1015_REG_CONFIG_OS_NOTBUSY (0x8000) // Read: Bit = 1 when device is not performing a conversion
#define ADS1015_REG_CONFIG_MUX_MASK (0x7000)
#define ADS1015_REG_CONFIG_MUX_DIFF_0_1 (0x0000) // Differential P = AIN0, N = AIN1 (default)
#define ADS1015_REG_CONFIG_MUX_DIFF_0_3 (0x1000) // Differential P = AIN0, N = AIN3
#define ADS1015_REG_CONFIG_MUX_DIFF_1_3 (0x2000) // Differential P = AIN1, N = AIN3
#define ADS1015_REG_CONFIG_MUX_DIFF_2_3 (0x3000) // Differential P = AIN2, N = AIN3
#define ADS1015_REG_CONFIG_MUX_SINGLE_0 (0x4000) // Single-ended AIN0
#define ADS1015_REG_CONFIG_MUX_SINGLE_1 (0x5000) // Single-ended AIN1
#define ADS1015_REG_CONFIG_MUX_SINGLE_2 (0x6000) // Single-ended AIN2
#define ADS1015_REG_CONFIG_MUX_SINGLE_3 (0x7000) // Single-ended AIN3
#define ADS1015_REG_CONFIG_PGA_MASK (0x0E00)
#define ADS1015_REG_CONFIG_PGA_6_144V (0x0000) // +/-6.144V range = Gain 2/3
#define ADS1015_REG_CONFIG_PGA_4_096V (0x0200) // +/-4.096V range = Gain 1
#define ADS1015_REG_CONFIG_PGA_2_048V (0x0400) // +/-2.048V range = Gain 2 (default)
#define ADS1015_REG_CONFIG_PGA_1_024V (0x0600) // +/-1.024V range = Gain 4
#define ADS1015_REG_CONFIG_PGA_0_512V (0x0800) // +/-0.512V range = Gain 8
#define ADS1015_REG_CONFIG_PGA_0_256V (0x0A00) // +/-0.256V range = Gain 16
#define ADS1015_REG_CONFIG_MODE_MASK (0x0100)
#define ADS1015_REG_CONFIG_MODE_CONTIN (0x0000) // Continuous conversion mode
#define ADS1015_REG_CONFIG_MODE_SINGLE (0x0100) // Power-down single-shot mode (default)
#define ADS1015_REG_CONFIG_DR_MASK (0x00E0)
#define ADS1015_REG_CONFIG_DR_128SPS (0x0000) // 128 samples per second
#define ADS1015_REG_CONFIG_DR_250SPS (0x0020) // 250 samples per second
#define ADS1015_REG_CONFIG_DR_490SPS (0x0040) // 490 samples per second
#define ADS1015_REG_CONFIG_DR_920SPS (0x0060) // 920 samples per second
#define ADS1015_REG_CONFIG_DR_1600SPS (0x0080) // 1600 samples per second (default)
#define ADS1015_REG_CONFIG_DR_2400SPS (0x00A0) // 2400 samples per second
#define ADS1015_REG_CONFIG_DR_3300SPS (0x00C0) // 3300 samples per second
#define ADS1015_REG_CONFIG_CMODE_MASK (0x0010)
#define ADS1015_REG_CONFIG_CMODE_TRAD (0x0000) // Traditional comparator with hysteresis (default)
#define ADS1015_REG_CONFIG_CMODE_WINDOW (0x0010) // Window comparator
#define ADS1015_REG_CONFIG_CPOL_MASK (0x0008)
#define ADS1015_REG_CONFIG_CPOL_ACTVLOW (0x0000) // ALERT/RDY pin is low when active (default)
#define ADS1015_REG_CONFIG_CPOL_ACTVHI (0x0008) // ALERT/RDY pin is high when active
#define ADS1015_REG_CONFIG_CLAT_MASK (0x0004) // Determines if ALERT/RDY pin latches once asserted
#define ADS1015_REG_CONFIG_CLAT_NONLAT (0x0000) // Non-latching comparator (default)
#define ADS1015_REG_CONFIG_CLAT_LATCH (0x0004) // Latching comparator
#define ADS1015_REG_CONFIG_CQUE_MASK (0x0003)
#define ADS1015_REG_CONFIG_CQUE_1CONV (0x0000) // Assert ALERT/RDY after one conversions
#define ADS1015_REG_CONFIG_CQUE_2CONV (0x0001) // Assert ALERT/RDY after two conversions
#define ADS1015_REG_CONFIG_CQUE_4CONV (0x0002) // Assert ALERT/RDY after four conversions
#define ADS1015_REG_CONFIG_CQUE_NONE (0x0003) // Disable the comparator and put ALERT/RDY in high state (default)
/*=========================================================================*/
typedef enum
{
GAIN_TWOTHIRDS = ADS1015_REG_CONFIG_PGA_6_144V,
GAIN_ONE = ADS1015_REG_CONFIG_PGA_4_096V,
GAIN_TWO = ADS1015_REG_CONFIG_PGA_2_048V,
GAIN_FOUR = ADS1015_REG_CONFIG_PGA_1_024V,
GAIN_EIGHT = ADS1015_REG_CONFIG_PGA_0_512V,
GAIN_SIXTEEN = ADS1015_REG_CONFIG_PGA_0_256V
} adsGain_t;
void Ads1015::ReadADC(unsigned int *aAdcValues, byte aCount)
{
// read the analog values:
for(byte i=0; i<aCount; i++)
{
//aAdcValues[i] = GetAdc(i);
aAdcValues[i] = readADC_SingleEnded(i);
}
}
float Ads1015::GetAdc(byte aChannel)
{
unsigned int lValue = 0;
lValue = readADC_SingleEnded(aChannel);
float lV = lValue;
lV = lV * cAdcRange;
return lV;
}
/**************************************************************************/
/*!
@brief Writes 16-bits to the specified destination register
*/
/**************************************************************************/
void Ads1015::writeAdcRegister(uint8_t reg, uint16_t value)
{
Wire.beginTransmission(ADS_I2C_ADDRESS);
Wire.write(reg);
Wire.write((uint8_t)(value>>8));
Wire.write((uint8_t)(value & 0xFF));
Wire.endTransmission();
}
/**************************************************************************/
/*!
@brief Writes 16-bits to the specified destination register
*/
/**************************************************************************/
uint16_t Ads1015::readAdcRegister(uint8_t reg)
{
Wire.beginTransmission(ADS_I2C_ADDRESS);
Wire.write(reg);
Wire.endTransmission();
Wire.requestFrom(ADS_I2C_ADDRESS, 2);
return ((Wire.read() << 8) | Wire.read());
}
/**************************************************************************/
/*!
@brief Gets a single-ended ADC reading from the specified channel
*/
/**************************************************************************/
uint16_t Ads1015::readADC_SingleEnded(uint8_t channel)
{
if (channel > 3)
{
return 0;
}
// Start with default values
uint16_t config = ADS1015_REG_CONFIG_CQUE_NONE | // Disable the comparator (default val)
ADS1015_REG_CONFIG_CLAT_NONLAT | // Non-latching (default val)
ADS1015_REG_CONFIG_CPOL_ACTVLOW | // Alert/Rdy active low (default val)
ADS1015_REG_CONFIG_CMODE_TRAD | // Traditional comparator (default val)
ADS1015_REG_CONFIG_DR_1600SPS | // samples per second
ADS1015_REG_CONFIG_MODE_SINGLE | // Single-shot mode (default)
ADS1015_REG_CONFIG_OS_SINGLE | // Set 'start single-conversion' bit
GAIN_ONE;
// Set single-ended input channel
switch (channel)
{
case (0):
config |= ADS1015_REG_CONFIG_MUX_SINGLE_0;
break;
case (1):
config |= ADS1015_REG_CONFIG_MUX_SINGLE_1;
break;
case (2):
config |= ADS1015_REG_CONFIG_MUX_SINGLE_2;
break;
case (3):
config |= ADS1015_REG_CONFIG_MUX_SINGLE_3;
break;
}
// Write config register to the ADC
writeAdcRegister(ADS1015_REG_POINTER_CONFIG, config);
// Wait for the conversion to complete
delay(ADS1115_CONVERSIONDELAY);
// Read the conversion results
return readAdcRegister(ADS1015_REG_POINTER_CONVERT);
}