/
generic-bigtreetech-manta-m5p.cfg
199 lines (166 loc) · 3.44 KB
/
generic-bigtreetech-manta-m5p.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
# This file contains common pin mappings for the BIGTREETECH Manta M5P
# To use this config, the firmware should be compiled for the
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
# and "USB (on PA11/PA12)" or "CAN bus (on PD0/PD1)".
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PC8
dir_pin: !PC9
enable_pin: !PA15
microsteps: 16
rotation_distance: 40
endstop_pin: ^PD3
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_y]
step_pin: PA10
dir_pin: !PA14
enable_pin: !PA13
microsteps: 16
rotation_distance: 40
endstop_pin: ^PD2
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_z]
step_pin: PC6
dir_pin: PC7
enable_pin: !PA9
microsteps: 16
rotation_distance: 8
endstop_pin: ^PC3
position_endstop: 0.0
position_max: 200
[extruder]
step_pin: PB12
dir_pin: !PB11
enable_pin: !PA8
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA1
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
#sensor_type:MAX31865
#sensor_pin: PA4
#spi_bus: spi1
#rtd_nominal_r: 100
#rtd_reference_r: 430
#rtd_num_of_wires: 2
#[filament_switch_sensor material_0]
#switch_pin: PC2
#[extruder1]
#step_pin: PB0
#dir_pin: PB1
#enable_pin: !PC4
#heater_pin: PA7
#sensor_pin: PA2
#...
[heater_bed]
heater_pin: PA5
sensor_type: Generic 3950
sensor_pin: PA0
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: PA4
#[heater_fan fan1]
#pin: PA3
#[heater_fan SoC_fan]
#pin: CB1:gpio79
#pin: RPI:gpio26
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
########################################
# TMC2209 configuration
########################################
#[tmc2209 stepper_x]
#uart_pin: PD9
#run_current: 0.800
#diag_pin: PD3
#[tmc2209 stepper_y]
#uart_pin: PD8
#run_current: 0.800
#diag_pin: PD2
#[tmc2209 stepper_z]
#uart_pin: PB10
#run_current: 0.800
#diag_pin: PC3
#[tmc2209 extruder]
#uart_pin: PB2
#run_current: 0.600
#diag_pin: PC2
#[tmc2209 extruder1]
#uart_pin: PA6
#run_current: 0.600
#diag_pin:
########################################
# TMC2130 configuration
########################################
#[tmc2130 stepper_x]
#cs_pin: PD9
#spi_bus: spi2
#run_current: 0.800
#stealthchop_threshold: 999999
#diag1_pin: PD3
#[tmc2130 stepper_y]
#cs_pin: PD8
#spi_bus: spi2
#run_current: 0.800
#stealthchop_threshold: 999999
#diag1_pin: PD2
#[tmc2130 stepper_z]
#cs_pin: PB10
#spi_bus: spi2
#run_current: 0.650
#stealthchop_threshold: 999999
#diag1_pin: PC3
#[tmc2130 extruder]
#cs_pin: PB2
#spi_bus: spi2
#run_current: 0.800
#stealthchop_threshold: 999999
#diag1_pin: PC2
#[tmc2130 extruder1]
#cs_pin: PA6
#spi_bus: spi2
#run_current: 0.800
#stealthchop_threshold: 999999
#diag1_pin:
[board_pins]
aliases:
# EXP1 header
EXP1_1=PD5, EXP1_3=PB3, EXP1_5=PB5, EXP1_7=PB7, EXP1_9=<GND>,
EXP1_2=PD4, EXP1_4=PD6, EXP1_6=PB4, EXP1_8=PB6, EXP1_10=<5V>,
# EXP2 header
EXP2_1=PB14, EXP2_3=PB8, EXP2_5=PC10, EXP2_7=PC12, EXP2_9=<GND>,
EXP2_2=PB13, EXP2_4=PB9, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
# See the sample-lcd.cfg file for definitions of common LCD displays.
#[bltouch]
#sensor_pin: PC13
#control_pin: PC15
# Proximity switch
#[probe]
#pin: PC15
#[neopixel my_neopixel1]
#pin: PC11
#[neopixel my_neopixel2]
#pin: PC14
#[adxl345]
#cs_pin: PC0
#spi_bus: spi2