-
-
Notifications
You must be signed in to change notification settings - Fork 5.2k
/
generic-bigtreetech-skr-v1.3.cfg
189 lines (159 loc) · 3.98 KB
/
generic-bigtreetech-skr-v1.3.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
# This file contains common pin mappings for the BIGTREETECH SKR V1.3
# board. To use this config, the firmware should be compiled for the
# LPC1768.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: P2.2
dir_pin: !P2.6
enable_pin: !P2.1
microsteps: 16
rotation_distance: 40
endstop_pin: P1.29 # P1.28 for X-max
position_endstop: 0
position_max: 320
homing_speed: 50
[stepper_y]
step_pin: P0.19
dir_pin: !P0.20
enable_pin: !P2.8
microsteps: 16
rotation_distance: 40
endstop_pin: P1.27 # P1.26 for Y-max
position_endstop: 0
position_max: 300
homing_speed: 50
[stepper_z]
step_pin: P0.22
dir_pin: P2.11
enable_pin: !P0.21
microsteps: 16
rotation_distance: 8
endstop_pin: P1.25 # P1.24 for Z-max
position_endstop: 0.5
position_max: 400
[extruder]
step_pin: P2.13
dir_pin: !P0.11
enable_pin: !P2.12
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: P2.7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: P0.24
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 260
#[extruder1]
#step_pin: P0.1
#dir_pin: P0.0
#enable_pin: !P0.10
#heater_pin: P2.4
#sensor_pin: P0.25
#...
[heater_bed]
heater_pin: P2.5
sensor_type: ATC Semitec 104GT-2
sensor_pin: P0.23
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: P2.3
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 200
max_accel: 2000
max_z_velocity: 25
max_z_accel: 100
########################################
# TMC2208 configuration
########################################
# For TMC2208 UART
# 1) Remove all of the jumpers below the stepper drivers
# 2) Place jumpers on the red pin headers labeled XUART (XUART, YUART etc.)
#[tmc2208 stepper_x]
#uart_pin: P1.17
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 stepper_y]
#uart_pin: P1.15
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 stepper_z]
#uart_pin: P1.10
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2208 extruder]
#uart_pin: P1.8
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2208 extruder1]
#uart_pin: P1.1
#run_current: 0.800
#stealthchop_threshold: 999999
########################################
# TMC2130 configuration
########################################
# For TMC SPI
# 1) Place jumpers on all the red pin headers under the stepper drivers
# 2) Remove jumpers from the red pin headers labeled XUART (XUART, YUART etc.)
#[tmc2130 stepper_x]
#cs_pin: P1.17
#spi_software_miso_pin: P0.5
#spi_software_mosi_pin: P4.28
#spi_software_sclk_pin: P0.4
##diag1_pin: P1.29
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_y]
#cs_pin: P1.15
#spi_software_miso_pin: P0.5
#spi_software_mosi_pin: P4.28
#spi_software_sclk_pin: P0.4
##diag1_pin: P1.27
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_z]
#cs_pin: P1.10
#spi_software_miso_pin: P0.5
#spi_software_mosi_pin: P4.28
#spi_software_sclk_pin: P0.4
##diag1_pin: P1.25
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2130 extruder]
#cs_pin: P1.8
#spi_software_miso_pin: P0.5
#spi_software_mosi_pin: P4.28
#spi_software_sclk_pin: P0.4
##diag1_pin: P1.28
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder1]
#cs_pin: P1.1
#spi_software_miso_pin: P0.5
#spi_software_mosi_pin: P4.28
#spi_software_sclk_pin: P0.4
##diag1_pin: P1.26
#run_current: 0.800
#stealthchop_threshold: 999999
########################################
# EXP1 / EXP2 (display) pins
########################################
[board_pins]
aliases:
# EXP1 header
EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
# EXP2 header
EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"
# See the sample-lcd.cfg file for definitions of common LCD displays.