CC2652R/CC1352P discussion

[Koenkk]

This is a continuation of #1429

[juslex]

Is anyone having connectivity and pairing problems involving zzh and zemismart switch (HGZB-42 and HGZB-43)?

[Gibbz]

I have a new zzh with the firmware Z-Stack_3.x.0 20201026 and pairing is not working at all. My stick is not receiving any mqtt messages. I'll try an older fw and see if that helps...

[Gibbz]

no luck with a different fw

[louis-genestier]

@Gibbz it's a little bit old but did u succeed ? Is your zzh on port ttyUSB0 ?

[Gibbz]

I did get it working, I think it was a software issue in the end.

[louis-genestier]

@Gibbz can you tell me which version of the firmware are you using please ? mine is last but z2m can't detect my zzh :/

[Sineos]

I'm currently running 20201113 successfully on my zzh

[juslex]

I have the same error with the same firmware version and also the beta version. In my case, I can only pair close to zzh. However, after taking the end device to its final location and pressing the button for it to connect to a closer router, it does not communicate losing the signal. To be able to paring it, yesterday I found out if I delete the router from the location and re-add it on z2m, I can do the pairing or connect the next end device to it. I suspect it's a firmware incompatibility With HGZB-42 and HGZB-43 my only kind of routers in my zigbee network.

[Hafi-2021]

Hello!

I have a board with CC2652P. Could you please explain which settings I have to change in order to build Z-Stack for this device?

I'm familar with Eclipse but not with CCS.

TIA!

[chbarg]

Please refer to #1429 (comment)

ProASV shared a couple good links about the CC2652P.

[jabadabadu]

I have bought mine zig-a-zig-ah! (CC2652R Stick) and updated it lately with Z-Stack-firmware (https://github.com/Koenkk/Z-Stack-firmware/blob/master/coordinator/Z-Stack_3.x.0/bin/CC26X2R1_20201026.zip), and when I tried to connect Aqara temperature, humidity and pressure sensors (https://www.zigbee2mqtt.io/devices/WSDCGQ11LM.html#xiaomi-wsdcgq11lm), couldn't succeed until I disconnected the antenna. The only one sensor with some of linkage (lqi:90) is located 2 metres from zzh!, other located sensors in the apartment are not available. Distances from them are not far - bathroom sensor located in range 5 metres; kitchen about 7 metres, and main room in 3 metres (and one wall). Should be there still a connection, but Zigbee2MQTT states there are none. Even after connected them all close to the zzh with disconnected antenna (to be seen), and then connecting antenna again and mounting sensors to theirs previous mounting points.

I am using Raspberry Pi 4 with 4 GB of RAM Model B Rev 1.2, bootable from SSD with Ugreen USB Adapter to USB 3.0, zzh! is connected to USB 2.0 (black one). Information from Home Assistant OS:

version: 2021.1.0
installation_type: Home Assistant OS
dev: false
hassio: true
docker: true
virtualenv: false
python_version: 3.8.7
os_name: Linux
os_version: 5.4.79-v8
arch: aarch64
timezone: Europe/Warsaw

host_os: Home Assistant OS 5.10
update_channel: stable
supervisor_version: 2020.12.7
docker_version: 19.03.13
disk_total: 116.7 GB
disk_used: 3.6 GB
healthy: true
supported: true
board: rpi4-64
supervisor_api: ok
version_api: ok
installed_addons: Mosquitto broker (5.1), Zigbee2mqtt (1.17.0.1), File editor (5.2.0), MariaDB (2.2.1), Terminal & SSH (8.10.0), zigbee2mqttassistant (0.3.157), Samba share (9.3.0), Log Viewer (0.9.1)

Zigbee2Mqtt configuration has settings:

serial:
  port: /dev/ttyUSB0
advanced:
  log_level: debug
  rtscts: false

[BigMike71]

try connect the Ugreen USB Adapter to USB 3.0 on your USB 2.0 Port!

USB3.0 has strong radiation within the Zigbee frequency. also had strong problems with my USB3.0 adapters and Zigbee. The Raspi4 needs no USB3.0 SSD speed for good working
since I plugged the Ugreen onto the USB2.0 everything is going fine

[jabadabadu]

That was a perfect solution. Everything is working now.

[exetico]

CC265R connected to zigbee2mqtt with S2E module

Hardware required

I've added ref-links to the AliExpress links. Let me know if i should remove it. But it's a good way to say thanks for the guide, right?

The PoE-parts are only needed, if you're planning to have a minimal setup at the receiver-end with no power outlets, or if you're interesting in trying something new (But you're using zigbee2mqtt, so I think you are ready to join the PoE-club too, right 😁?!)....

• LAUNCHXL-CC26X2R1-board
• USR-TCP232-T2 S2E adapter (non-ref)
• POE-Splitter (non-ref)
• Four jumper cables
• One networkcable
• A switch with PoE, or a PoE Injector (non-ref) - or alternative, just power the CC26X2R1 with a spare USB power-adapter from a cell-phone or so, if that's an option for you.

Please note that PoE splitters can be found in many qualities. It's always hard to tell which are the best to go with. If you're feel it's better to not cheap-our, maybe check this one (non-ref). I've bought the cheap one...

Connection between CC1352P and the S2E module

If people are looking for a solution for their CC2652R with S2E, here's a few images:

First move the two jumpers, so both of them are disconnected. It's just easier to have them on the board, so I've just moved them as shown on the image.

Great! You've just exposed the TX and RX pins 🤯 (The two pins we seperated from the jumpers), but I like to follow the datasheet for pin-outs. Scroll down, and you'll find my wirering guide 🤟😁...

Now wire like so:

CC2652R	S2E
3V3	3.3V:VCD
GND	GND
DIO2	TXD
DIO3	RXD

On the CC1352P, DIO2 are RX, and DIO3 are TX. And yes, it should always go RX > TX and TX > RX.

You can use the pin-outs, which we just exposed by moving the jumpers, but I like to follow the normal pin-out diagram. It's also a good thing to have all wires at the same location on the board. But, it's up to you mate - it's a free country... or at least, where I live!

S2E module

You'll find out that your module is locked to a static IP.

Normally it's 192.168.0.7 or 192.168.1.7, so good luck with connection to it 😉 It can be a pain to establish the first heartbeat, but you'll get there! Trust me - just take your time ⏳.

Use admin:admin as username and password, after you've finally connected to it.

Change the static IP to what you need, or set it to DHCP, and create a MAC-adress mapping in your router (that's my suggestion). I've defined a new static IP first, and changed it to DHCP here after.

Go to the "Serial Port" page, and change "Local Port Number" if needed. Hereafter change "Work Mode" to "TCP Server" <-- Very important.

Here's the "Serial Port" page:

And here's the "Local IP Config":

zigbee2mqtt configuration

I'm running zigbee2mqtt powered by the official docker container, and that's ready for a setup where the serial connection are handled through the network.

Therefore, you'll only need to change the following things in your configuration:

serial:
  port: 'tcp://10.0.0.120:20108'
advanced:
  ...
  baudrate: 115200
  rtscts: false

Note that I've removed other things within "advanced".

Reboot zigbee2mqtt, and cross your fingers. Now you should be good to go 😃💡 🔌!

If you're not running zigbee2mqtt in a container, take a look at this page.

Links

• Ti's Ref for Pinout
• Old issue where this is brought up

Pin-out diagram

[exetico]

Thanks Niels! I'm actually considering to just print it... But lets' see. (I've read your recommendation)

@DeltaAngle You're more than welcome :-)

[valepe]

CC265R connected to zigbee2mqtt with S2E module

Hi, I hope you can help me. I have a CC1352P-2 actually connected via USB to a Synology NAS running zigbee2mqtt in a docker container.
It works flawlessy. I'd like to change this connection to a SER module because I'm switching to a server with ESXi and I prefer to ditch the USB connection. I bought a USR-TCP232-T2 module.

I followed your guide to setup everything but zigbee2mqtt failed to start because it can't connect to to the module (SRSP - SYS - ping after 6000ms).
While connecting; I'm looking the main page of the module and I see the incoming connection from zigbee2mqtt but the module reports RX traffic only. Nothing leaving it.

I double checked all the wire connections and all the setup in the module and in the yaml file. But nothing :(

By now I restored the jumpers and reconnect it via USB.

[exetico]

Please double check the wires, and confirm that every config are made correctly - also the crossing of TX and RX.

With that said, have you tried to connect to the SER module in a terminal or so? That's maybe a good idea to confirm that it's working as expected.

My system are working so much better, after ditching the USB interface for a Ethernet-based solution.

I know this aren't that helpful, but we must start with something 😅. It's pretty hard to help with things like this, without confirming every step made.

[valepe]

Please double check the wires, and confirm that every config are made correctly - also the crossing of TX and RX.

With that said, have you tried to connect to the SER module in a terminal or so? That's maybe a good idea to confirm that it's working as expected.

My system are working so much better, after ditching the USB interface for a Ethernet-based solution.

I know this aren't that helpful, but we must start with something 😅. It's pretty hard to help with things like this, without confirming every step made.

After wrote the post, I checked the module with the test app from USRIOT (looping serial and ethernet interfaces on the same PC) and I found that the serial chip was able to receive data but not to transmit.

Luckily I bought two of them and I tested the second one that worked fine. So next days I will retry.

Update:
All is worked at first time with the second module. :-)

[klein0r]

Thanks a lot! I've designed a small PCB to connect the USR module to the CC26X2R1:
https://github.com/klein0r/pcb-cc26x2r1-hat

[gabric098]

Yesterday I flashed the latest router firmware for CC2652R downloaded from here https://github.com/Koenkk/Z-Stack-firmware/raw/master/router/Z-Stack_3.x.0/bin/CC2652R_router_20210128.zip on my zzh! stick.

The stick has been working for quite a while as coordinator with the coordinator firmware so, I can confirm that it's not a stick issue.
Once flashed with the router firmware, I plugged it into a usb adapter (just to power it) and I can't see any lights going off, is it normal?

Assuming it is normal, following the instructions found here: https://www.zigbee2mqtt.io/information/supported_adapters.html#router. I've tried several time to press the button on the stick in order to reset/pair the device but with no luck, I don't see any message related to the router in the z2m logs, as there was no message coming from the stick.

The coordinator is another zzh! stick running latest coordinator firmware.

Any idea about what could be wrong?
thank you.
Gab

[ersiensi]

Hi Koenkk
Today I flashed the new CC2652R from Electrolama zig-a-zig-ah! (zzh!) to the latest version of CC2652R_coordinator_20210120.zip on a clean installation of Hassio + MQTT + Zigbee2mqtt. Finally, I managed to start the coordinator and successfully pair the first device for testing the Sonoff sensor (SNZB-04). However, I cannot connect to the Xiaomi Aqara SKUE64782 switch. I have been using these switches without problems for a long time in another Rpi with Hassio and the cc2531 coordinator with your software. The log does not record any errors and does not respond to the switch during pairing. The LED light on the CC2652R coordinator does not light up after uploaded the latest firmware, but the coordinator reportsare without errors in the logs. I tried to change channels to 11, 12, 25 but it didn't help. The switches operate on the old CC2531 on 11 channel.

Debug: Z2M_log.txt

Thank you for your answer.
Robert

[piit79]

@ersiensi I also had troubles pairing these switches before. When you reset them for pairing, make sure to start and keep pressing the switch every second to make sure it doesn't go to sleep. That's what worked for me.

[ersiensi]

@ersiensi Tiež som mal predtým problémy so spárovaním týchto prepínačov. Keď ich resetujete na párovanie, nezabudnite spustiť a každú sekundu stlačte vypínač, aby ste sa uistili, že nejde spať. To sa mi osvedčilo.

Hi piit79. I have been using 1, 2 and 3 Aqara pushbutton switches for a long time and I had no problems with the CC2531 even when pairing. I tried to keep in touch at second intervals as you wrote, but it didn't help. I think the problem is in my new CC2652R, because after flashing it doesn't even light up and I tried to flash it via USB3 and USB2 to avoid possible problems. It didn't help.

[rvalle]

With CC2652RB I am experiencing xiaomi devices kicked out of network, but only when using the router firmware, and not the coordinator firmware see Koenkk/Z-Stack-firmware#307

Which I think it is strange...

[frank-f]

I'm not sure, if this is the right place to ask about this. I designed my own adapter using an RF-Star RF-BM-2652P2 board. It's all working fine, but the LEDs connected to DIO 6 and 7 never light up. From what I remember one of them should light up when joining is enabled and the other one on network traffic - or am I wrong on this?
The connection path is DIO -> 1k resistor -> LED -> GND.
Any idea what could be wrong here? Or do LEDs just not work with CC2652 adapters?

[Gr3G63]

Hi every one.
I'm trying to build a router from a CC1352P-2 LAUNCHPAD (MAC Address: 0x00124b001ca1bb3b). I have download the right firmware (https://github.com/Koenkk/Z-Stack-firmware/blob/master/router/Z-Stack_3.x.0/bin/CC1352P2_CC2652P_launchpad_router_20210128.zip) and try to flash it with Uniflash an Flash Programmer. But it didn't work. The pairing is still unsuccesful.

The only thing I saw in the log file is when the pairing error occure, the transaction ID is different from the permit_join:

info  2021-12-14 18:11:02: MQTT publish: topic 'zigbee2mqtt/bridge/response/permit_join', payload '{"data":{"time":254,"value":true},"status":"ok","transaction":"ovqyx-9"}'
...
info  2021-12-14 18:12:10: MQTT publish: topic 'zigbee2mqtt/bridge/response/device/configure', payload '{"data":{"id":"0x00124b001ca1bb3b"},"error":"Device '0x00124b001ca1bb3b' cannot be configured","status":"error","transaction":"ovqyx-10"}'

I'm using:

• a Pi4 raspbian buster
• Zigbee2MQTT version 1.22.1
• an other CC1352P-2 LAUNCHPAD as a coordinator (MAC Address : 0x00124b001ca1b3ad), build 20210708
• Everything is working well since 1 year. My network is just growning up, and I need a good router to listen what happen in my fresh build garage

info  2021-12-14 18:11:02: MQTT publish: topic 'zigbee2mqtt/bridge/response/permit_join', payload '{"data":{"time":254,"value":true},"status":"ok","transaction":"ovqyx-9"}'
info  2021-12-14 18:11:25: Device '0x00124b001ca1bb3b' joined
info  2021-12-14 18:11:26: MQTT publish: topic 'zigbee2mqtt/bridge/event', payload '{"data":{"friendly_name":"0x00124b001ca1bb3b","ieee_address":"0x00124b001ca1bb3b"},"type":"device_joined"}'
info  2021-12-14 18:11:26: MQTT publish: topic 'zigbee2mqtt/bridge/log', payload '{"message":{"friendly_name":"0x00124b001ca1bb3b"},"type":"device_connected"}'
info  2021-12-14 18:11:26: MQTT publish: topic 'zigbee2mqtt/0x00124b001ca1bb3b', payload '{"last_seen":"2021-12-14T18:11:26+01:00"}'
info  2021-12-14 18:11:26: Starting interview of '0x00124b001ca1bb3b'
info  2021-12-14 18:11:26: MQTT publish: topic 'zigbee2mqtt/bridge/event', payload '{"data":{"friendly_name":"0x00124b001ca1bb3b","ieee_address":"0x00124b001ca1bb3b","status":"started"},"type":"device_interview"}'
info  2021-12-14 18:11:26: MQTT publish: topic 'zigbee2mqtt/bridge/log', payload '{"message":"interview_started","meta":{"friendly_name":"0x00124b001ca1bb3b"},"type":"pairing"}'
debug 2021-12-14 18:11:26: Received MQTT message on 'zigbee2mqtt/bridge/config/devices/get' with data ''
info  2021-12-14 18:11:26: MQTT publish: topic 'zigbee2mqtt/bridge/config/devices', payload '[{"dateCode":"20210708","friendly_name":"Coordinator","ieeeAddr":"0x00124b001ca1b3ad","lastSeen":1639501886154,"networkAddress":0,"softwareBuildID":"zStack3x0","type":"Coordinator"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Salon","hardwareVersion":30,"ieeeAddr":"0x00158d000582e341","lastSeen":1639500616845,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":17724,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Chambre","hardwareVersion":30,"ieeeAddr":"0x00158d00019d1ad8","lastSeen":1639500784001,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":45490,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20180629","description":"Aqara wireless switch (with gyroscope)","friendly_name":"Switch_1","hardwareVersion":1,"ieeeAddr":"0x00158d000521667a","lastSeen":1639500920375,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WXKG12LM","modelID":"lumi.sensor_switch.aq3","networkAddress":16383,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Bureau","hardwareVersion":30,"ieeeAddr":"0x00158d0005828cb5","lastSeen":1639500626297,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":43345,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20140331CNEF****","description":"SMART+ CLASSIC A 60 TW","friendly_name":"Ampoule_Cellier","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa00af75ae","lastSeen":1639501200357,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AC03642","modelID":"CLA60 TW OSRAM","networkAddress":34739,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.10","type":"Router","vendor":"OSRAM"},{"description":"Aqara wireless switch (with gyroscope)","friendly_name":"Switch_2","ieeeAddr":"0x00158d0005216614","lastSeen":1639499995548,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WXKG12LM","modelID":"lumi.sensor_switch.aq3","networkAddress":49737,"powerSource":"Battery","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"","description":"2 gang smart dimmer switch module with neutral","friendly_name":"Dimmer_Chambre","hardwareVersion":1,"ieeeAddr":"0x5c0272fffedaa890","lastSeen":1639499924623,"manufacturerID":4098,"manufacturerName":"_TYZB01_v8gtiaed","model":"QS-Zigbee-D02-TRIAC-2C-LN","modelID":"TS110F","networkAddress":11447,"powerSource":"Mains (single phase)","type":"Router","vendor":"Lonsonho"},{"dateCode":"20190723","description":"TRADFRI ON/OFF switch","friendly_name":"Inter_Chevet_Marion","hardwareVersion":1,"ieeeAddr":"0xbc33acfffe9e6d32","lastSeen":1639465804903,"manufacturerID":4476,"manufacturerName":"IKEA of Sweden","model":"E1743","modelID":"TRADFRI on/off switch","networkAddress":11795,"powerSource":"Battery","softwareBuildID":"2.2.010","type":"EndDevice","vendor":"IKEA"},{"dateCode":"20190723","description":"TRADFRI ON/OFF switch","friendly_name":"Inter_Chevet_Greg","hardwareVersion":1,"ieeeAddr":"0xbc33acfffe9cf365","lastSeen":1639476613278,"manufacturerID":4476,"manufacturerName":"IKEA of Sweden","model":"E1743","modelID":"TRADFRI on/off switch","networkAddress":11397,"powerSource":"Battery","softwareBuildID":"2.2.010","type":"EndDevice","vendor":"IKEA"},{"dateCode":"20170627","description":"Aqara human body movement and illuminance sensor","friendly_name":"motion_sensor_cellier","hardwareVersion":1,"ieeeAddr":"0x00158d0006a0aa75","lastSeen":1639500254360,"manufacturerID":4151,"manufacturerName":"LUMI","model":"RTCGQ11LM","modelID":"lumi.sensor_motion.aq2","networkAddress":64111,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20210320","description":"Zigbee two way smart switch","friendly_name":"Switch_spots_terrasse","hardwareVersion":1,"ieeeAddr":"0x00124b0024c2db18","lastSeen":1639483378065,"manufacturerID":4742,"manufacturerName":"SONOFF","model":"ZBMINI","modelID":"01MINIZB","networkAddress":7171,"powerSource":"Mains (single phase)","softwareBuildID":"2.0.0","type":"Router","vendor":"SONOFF"},{"dateCode":"20140331DEOS****","description":"Smart+ plug","friendly_name":"Prise_sapin","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa0a0a7424","lastSeen":1639498710234,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AB3257001NJ","modelID":"Plug 01","networkAddress":25711,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.09","type":"Router","vendor":"OSRAM"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Chambre_Bebe","hardwareVersion":1,"ieeeAddr":"0x00124b0024ce1e4b","lastSeen":1639500857775,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":25623,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Garage","hardwareVersion":1,"ieeeAddr":"0x00124b00246ce6fd","lastSeen":1639500842471,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":39338,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Exterieur","hardwareVersion":1,"ieeeAddr":"0x00124b0023b45e0c","lastSeen":1639501249624,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":37117,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Contact sensor","friendly_name":"Etat_Porte_Garage","hardwareVersion":1,"ieeeAddr":"0x00124b00245c6d43","lastSeen":1639499666538,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-04","modelID":"DS01","networkAddress":14393,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20140331DEOS****","description":"Smart+ plug","friendly_name":"Prise_guirlande","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa0a0a72d9","lastSeen":1639500105673,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AB3257001NJ","modelID":"Plug 01","networkAddress":55794,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.09","type":"Router","vendor":"OSRAM"},{"description":"-","friendly_name":"0x00124b001ca1bb3b","ieeeAddr":"0x00124b001ca1bb3b","lastSeen":1639501886048,"networkAddress":63830,"type":"Unknown","vendor":"-"}]'
debug 2021-12-14 18:11:26: Received MQTT message on 'zigbee2mqtt/bridge/config/devices' with data '[{"dateCode":"20210708","friendly_name":"Coordinator","ieeeAddr":"0x00124b001ca1b3ad","lastSeen":1639501886154,"networkAddress":0,"softwareBuildID":"zStack3x0","type":"Coordinator"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Salon","hardwareVersion":30,"ieeeAddr":"0x00158d000582e341","lastSeen":1639500616845,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":17724,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Chambre","hardwareVersion":30,"ieeeAddr":"0x00158d00019d1ad8","lastSeen":1639500784001,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":45490,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20180629","description":"Aqara wireless switch (with gyroscope)","friendly_name":"Switch_1","hardwareVersion":1,"ieeeAddr":"0x00158d000521667a","lastSeen":1639500920375,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WXKG12LM","modelID":"lumi.sensor_switch.aq3","networkAddress":16383,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Bureau","hardwareVersion":30,"ieeeAddr":"0x00158d0005828cb5","lastSeen":1639500626297,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":43345,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20140331CNEF****","description":"SMART+ CLASSIC A 60 TW","friendly_name":"Ampoule_Cellier","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa00af75ae","lastSeen":1639501200357,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AC03642","modelID":"CLA60 TW OSRAM","networkAddress":34739,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.10","type":"Router","vendor":"OSRAM"},{"description":"Aqara wireless switch (with gyroscope)","friendly_name":"Switch_2","ieeeAddr":"0x00158d0005216614","lastSeen":1639499995548,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WXKG12LM","modelID":"lumi.sensor_switch.aq3","networkAddress":49737,"powerSource":"Battery","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"","description":"2 gang smart dimmer switch module with neutral","friendly_name":"Dimmer_Chambre","hardwareVersion":1,"ieeeAddr":"0x5c0272fffedaa890","lastSeen":1639499924623,"manufacturerID":4098,"manufacturerName":"_TYZB01_v8gtiaed","model":"QS-Zigbee-D02-TRIAC-2C-LN","modelID":"TS110F","networkAddress":11447,"powerSource":"Mains (single phase)","type":"Router","vendor":"Lonsonho"},{"dateCode":"20190723","description":"TRADFRI ON/OFF switch","friendly_name":"Inter_Chevet_Marion","hardwareVersion":1,"ieeeAddr":"0xbc33acfffe9e6d32","lastSeen":1639465804903,"manufacturerID":4476,"manufacturerName":"IKEA of Sweden","model":"E1743","modelID":"TRADFRI on/off switch","networkAddress":11795,"powerSource":"Battery","softwareBuildID":"2.2.010","type":"EndDevice","vendor":"IKEA"},{"dateCode":"20190723","description":"TRADFRI ON/OFF switch","friendly_name":"Inter_Chevet_Greg","hardwareVersion":1,"ieeeAddr":"0xbc33acfffe9cf365","lastSeen":1639476613278,"manufacturerID":4476,"manufacturerName":"IKEA of Sweden","model":"E1743","modelID":"TRADFRI on/off switch","networkAddress":11397,"powerSource":"Battery","softwareBuildID":"2.2.010","type":"EndDevice","vendor":"IKEA"},{"dateCode":"20170627","description":"Aqara human body movement and illuminance sensor","friendly_name":"motion_sensor_cellier","hardwareVersion":1,"ieeeAddr":"0x00158d0006a0aa75","lastSeen":1639500254360,"manufacturerID":4151,"manufacturerName":"LUMI","model":"RTCGQ11LM","modelID":"lumi.sensor_motion.aq2","networkAddress":64111,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20210320","description":"Zigbee two way smart switch","friendly_name":"Switch_spots_terrasse","hardwareVersion":1,"ieeeAddr":"0x00124b0024c2db18","lastSeen":1639483378065,"manufacturerID":4742,"manufacturerName":"SONOFF","model":"ZBMINI","modelID":"01MINIZB","networkAddress":7171,"powerSource":"Mains (single phase)","softwareBuildID":"2.0.0","type":"Router","vendor":"SONOFF"},{"dateCode":"20140331DEOS****","description":"Smart+ plug","friendly_name":"Prise_sapin","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa0a0a7424","lastSeen":1639498710234,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AB3257001NJ","modelID":"Plug 01","networkAddress":25711,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.09","type":"Router","vendor":"OSRAM"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Chambre_Bebe","hardwareVersion":1,"ieeeAddr":"0x00124b0024ce1e4b","lastSeen":1639500857775,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":25623,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Garage","hardwareVersion":1,"ieeeAddr":"0x00124b00246ce6fd","lastSeen":1639500842471,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":39338,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Exterieur","hardwareVersion":1,"ieeeAddr":"0x00124b0023b45e0c","lastSeen":1639501249624,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":37117,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Contact sensor","friendly_name":"Etat_Porte_Garage","hardwareVersion":1,"ieeeAddr":"0x00124b00245c6d43","lastSeen":1639499666538,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-04","modelID":"DS01","networkAddress":14393,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20140331DEOS****","description":"Smart+ plug","friendly_name":"Prise_guirlande","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa0a0a72d9","lastSeen":1639500105673,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AB3257001NJ","modelID":"Plug 01","networkAddress":55794,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.09","type":"Router","vendor":"OSRAM"},{"description":"-","friendly_name":"0x00124b001ca1bb3b","ieeeAddr":"0x00124b001ca1bb3b","lastSeen":1639501886048,"networkAddress":63830,"type":"Unknown","vendor":"-"}]'
info  2021-12-14 18:11:26: MQTT publish: topic 'zigbee2mqtt/bridge/log', payload '{"message":[{"dateCode":"20210708","friendly_name":"Coordinator","ieeeAddr":"0x00124b001ca1b3ad","lastSeen":1639501886166,"networkAddress":0,"softwareBuildID":"zStack3x0","type":"Coordinator"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Salon","hardwareVersion":30,"ieeeAddr":"0x00158d000582e341","lastSeen":1639500616845,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":17724,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Chambre","hardwareVersion":30,"ieeeAddr":"0x00158d00019d1ad8","lastSeen":1639500784001,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":45490,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20180629","description":"Aqara wireless switch (with gyroscope)","friendly_name":"Switch_1","hardwareVersion":1,"ieeeAddr":"0x00158d000521667a","lastSeen":1639500920375,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WXKG12LM","modelID":"lumi.sensor_switch.aq3","networkAddress":16383,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20191205","description":"Aqara temperature, humidity and pressure sensor","friendly_name":"Bureau","hardwareVersion":30,"ieeeAddr":"0x00158d0005828cb5","lastSeen":1639500626297,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WSDCGQ11LM","modelID":"lumi.weather","networkAddress":43345,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20140331CNEF****","description":"SMART+ CLASSIC A 60 TW","friendly_name":"Ampoule_Cellier","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa00af75ae","lastSeen":1639501200357,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AC03642","modelID":"CLA60 TW OSRAM","networkAddress":34739,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.10","type":"Router","vendor":"OSRAM"},{"description":"Aqara wireless switch (with gyroscope)","friendly_name":"Switch_2","ieeeAddr":"0x00158d0005216614","lastSeen":1639499995548,"manufacturerID":4151,"manufacturerName":"LUMI","model":"WXKG12LM","modelID":"lumi.sensor_switch.aq3","networkAddress":49737,"powerSource":"Battery","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"","description":"2 gang smart dimmer switch module with neutral","friendly_name":"Dimmer_Chambre","hardwareVersion":1,"ieeeAddr":"0x5c0272fffedaa890","lastSeen":1639499924623,"manufacturerID":4098,"manufacturerName":"_TYZB01_v8gtiaed","model":"QS-Zigbee-D02-TRIAC-2C-LN","modelID":"TS110F","networkAddress":11447,"powerSource":"Mains (single phase)","type":"Router","vendor":"Lonsonho"},{"dateCode":"20190723","description":"TRADFRI ON/OFF switch","friendly_name":"Inter_Chevet_Marion","hardwareVersion":1,"ieeeAddr":"0xbc33acfffe9e6d32","lastSeen":1639465804903,"manufacturerID":4476,"manufacturerName":"IKEA of Sweden","model":"E1743","modelID":"TRADFRI on/off switch","networkAddress":11795,"powerSource":"Battery","softwareBuildID":"2.2.010","type":"EndDevice","vendor":"IKEA"},{"dateCode":"20190723","description":"TRADFRI ON/OFF switch","friendly_name":"Inter_Chevet_Greg","hardwareVersion":1,"ieeeAddr":"0xbc33acfffe9cf365","lastSeen":1639476613278,"manufacturerID":4476,"manufacturerName":"IKEA of Sweden","model":"E1743","modelID":"TRADFRI on/off switch","networkAddress":11397,"powerSource":"Battery","softwareBuildID":"2.2.010","type":"EndDevice","vendor":"IKEA"},{"dateCode":"20170627","description":"Aqara human body movement and illuminance sensor","friendly_name":"motion_sensor_cellier","hardwareVersion":1,"ieeeAddr":"0x00158d0006a0aa75","lastSeen":1639500254360,"manufacturerID":4151,"manufacturerName":"LUMI","model":"RTCGQ11LM","modelID":"lumi.sensor_motion.aq2","networkAddress":64111,"powerSource":"Battery","softwareBuildID":"3000-0001","type":"EndDevice","vendor":"Xiaomi"},{"dateCode":"20210320","description":"Zigbee two way smart switch","friendly_name":"Switch_spots_terrasse","hardwareVersion":1,"ieeeAddr":"0x00124b0024c2db18","lastSeen":1639483378065,"manufacturerID":4742,"manufacturerName":"SONOFF","model":"ZBMINI","modelID":"01MINIZB","networkAddress":7171,"powerSource":"Mains (single phase)","softwareBuildID":"2.0.0","type":"Router","vendor":"SONOFF"},{"dateCode":"20140331DEOS****","description":"Smart+ plug","friendly_name":"Prise_sapin","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa0a0a7424","lastSeen":1639498710234,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AB3257001NJ","modelID":"Plug 01","networkAddress":25711,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.09","type":"Router","vendor":"OSRAM"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Chambre_Bebe","hardwareVersion":1,"ieeeAddr":"0x00124b0024ce1e4b","lastSeen":1639500857775,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":25623,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Garage","hardwareVersion":1,"ieeeAddr":"0x00124b00246ce6fd","lastSeen":1639500842471,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":39338,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Temperature and humidity sensor","friendly_name":"Temp_Hum_Exterieur","hardwareVersion":1,"ieeeAddr":"0x00124b0023b45e0c","lastSeen":1639501249624,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-02","modelID":"TH01","networkAddress":37117,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20201026","description":"Contact sensor","friendly_name":"Etat_Porte_Garage","hardwareVersion":1,"ieeeAddr":"0x00124b00245c6d43","lastSeen":1639499666538,"manufacturerID":0,"manufacturerName":"eWeLink","model":"SNZB-04","modelID":"DS01","networkAddress":14393,"powerSource":"Battery","type":"EndDevice","vendor":"SONOFF"},{"dateCode":"20140331DEOS****","description":"Smart+ plug","friendly_name":"Prise_guirlande","hardwareVersion":1,"ieeeAddr":"0x7cb03eaa0a0a72d9","lastSeen":1639500105673,"manufacturerID":48042,"manufacturerName":"OSRAM","model":"AB3257001NJ","modelID":"Plug 01","networkAddress":55794,"powerSource":"Mains (single phase)","softwareBuildID":"V1.05.09","type":"Router","vendor":"OSRAM"},{"description":"-","friendly_name":"0x00124b001ca1bb3b","ieeeAddr":"0x00124b001ca1bb3b","lastSeen":1639501886048,"networkAddress":63830,"type":"Unknown","vendor":"-"}],"type":"devices"}'
debug 2021-12-14 18:12:10: Received MQTT message on 'zigbee2mqtt/bridge/request/device/configure' with data '{"id":"0x00124b001ca1bb3b","transaction":"ovqyx-10"}'
info  2021-12-14 18:12:10: MQTT publish: topic 'zigbee2mqtt/bridge/response/device/configure', payload '{"data":{"id":"0x00124b001ca1bb3b"},"error":"Device '0x00124b001ca1bb3b' cannot be configured","status":"error","transaction":"ovqyx-10"}'

Is someone had already build a router using CC1352P-2 ?

Many thanks for your help

[Gr3G63]

Problem solved with the firmware from @ptvoinfo (https://ptvo.info/cc2652r1-cc2652rb-cc2652p-cc1352p2-configurable-router-firmware-748/)
Solution find here: Koenkk/Z-Stack-firmware#273

Many thanks !! I will give you my feedback on this custom firmware (inside the right thread : 273)

[jamess5]

Hi all, not sure if anyone can help if certain attributes are not coming through...

I have previously used Docker, with a Zigbee2MQTT container, which worked well with my zigbee motion devices. It fed through the occupancy status correctly.

I am now in the process of moving this to Hassio - I have installed and configured the add-on within Hassio. It seems to work fine for all my zigbee devices. It has also found and successfully paired, and interview successful for each of them. However, there are a few attributes not fed through. One of these is occupancy. It shows 'Occupancy : N/A', and in the payload it's not there.

Has anyone experienced this before? I'm using the same Zigbee stick CC2652RB, the motion sensors are Samsung SmartThings (2015 model), I've disabled and removed the Docker container, and all seems to be connected to the network, it worked previously, but doesn't seem to work now. I have 3 of the same sensors, and the issue appears on all 3.

Any advice/suggestions would be appreciated!

[deiger]

Thank you for the amazing work on this!
Have you considered adding support for Thread? According to TI it should be possible for these chips to support Zigbee and Thread at once.
This will likely also be helpful as a precursor to Matter.

[hartmood]

I would also be very interested to know if the CC1352P-2 supports this. I put a lot of time into it, especially soldering the bridge was not easy. The range is terrific. It would be a shame if I had to part with it.

[Spyky]

Hello All,

I just changed from xiaomi gateway to zigbee dongle.
Most of the things are working. I have a Aqara wireless switch [WXKG12LM].
In domoticz devices i see the button, but online the voltage. In the mqtt log i see it when i add the device. How do i get the device in domoticz? Anyone an suggestion?
In domoticz i only see the voltage

Log:
info 2022-02-16 18:50:20: MQTT publish: topic 'zigbee2mqtt/bridge/event', paylo ad '{"data":{"definition":{"description":"Aqara wireless switch (with gyroscope) ","exposes":[{"access":1,"description":"Remaining battery in %","name":"battery" ,"property":"battery","type":"numeric","unit":"%","value_max":100,"value_min":0} ,{"access":1,"description":"Triggered action (e.g. a button click)","name":"acti on","property":"action","type":"enum","values":["single","double","hold","releas e","shake"]},{"access":1,"description":"Voltage of the battery in millivolts","n ame":"voltage","property":"voltage","type":"numeric","unit":"mV"},{"access":1,"d escription":"Link quality (signal strength)","name":"linkquality","property":"li nkquality","type":"numeric","unit":"lqi","value_max":255,"value_min":0}],"model" :"WXKG12LM","options":[{"access":2,"description":"Set to false to disable the le gacy integration (highly recommended), will change structure of the published pa yload (default true).","name":"legacy","property":"legacy","type":"binary","valu e_off":false,"value_on":true}],"supports_ota":false,"vendor":"Xiaomi"},"friendly _name":"0x00158d0001eba4bd","ieee_address":"0x00158d0001eba4bd","status":"succes sful","supported":true},"type":"device_interview"}'

Frontend after double click:
MQTT publish: topic 'zigbee2mqtt/Xiaomi Button Hal', payload '{"action":"double","battery":100,"click":"double","linkquality":189,"voltage":3005}'
Info MQTT publish: topic 'zigbee2mqtt/Xiaomi Button Hal/action', payload 'double'
Info MQTT publish: topic 'zigbee2mqtt/Xiaomi Button Hal/click', payload 'double'

Domoticz devices:

Xiaomi Button Hal voltage | General | Voltage | 3.005 V

[Spyky]

Anyone an idea??

[elektrinis]

Hi,

I have a sonoff stick with older firmware and also having issues with some of my devices. Not sure if this can be caused by coordinator, so asking here.
The issues are that some devices won't update their status (like a door sensor, a wall switch), but will listen to home assistant commands. Like, wall switch will switch when commanded, but will not update the status when switched physically. Also light dimmer will adjust the brightness, but the status may still be off.
I have repaired some of the issues by flipping the breaker or re-pairing, but they come back.

I want your opinion if it's worth updating the firmware, as it's a lengthy/risky task that I'd like to avoir if not necessary.

[lux73]

afaik there is a lot of fixes in the newer Firmwares so for me it's allways worth updating

BUT i don't know it will be affect your actual Configuration - some Users have to rebuild the entire Zigbee Network after upgrading

i never experienced this behaviour with my CC2652RB - but you have be warned!!!

[elektrinis]

Thanks a lot. I'll skip it for now, will look for a time when I'll have two spare days to trouble shoot. Probably never. :)