Skip to content

Latest commit

 

History

History
120 lines (87 loc) · 3.86 KB

fly_e3_v2.md

File metadata and controls

120 lines (87 loc) · 3.86 KB
Raw
title tags keywords last_updated summary sidebar permalink folder comments toc datatable boardname version mcu fly_e3_v2_img1 fly_e3_v2_cap1 fly_e3_v2_img2 fly_3_v2_cap2 fly_e3_v2_img3 fly_3_v2_cap3
Fly-E3-v2 General Information
17/02/2024
General information regarding the Fly-E3-v2
mydoc_sidebar
fly_e3_v2.html
mydoc
false
true
true
Fly-E3-v2
v2
fly-e3_v2
fly-e3_v2/fly-e3_v2_image.webp
Fly-E3-v2 Overview
fly-e3_v2/fly_e3_jumpers.png
Fly-E3-v2 Driver Jumper Locations
fly-e3_v2/fly-e3_v2_dimensions.webp
Fly-E3-v2 dimensions
 
{% capture boardname %}{{ page.boardname }}{% endcapture %}

{% capture mcu %}{{ page.mcu }}{% endcapture %}

{% capture fly_e3_v2_img1 %}{{page.fly_e3_v2_img1 }}{% endcapture %}
{% capture fly_e3_v2_cap1 %}{{page.fly_e3_v2_cap1 }}{% endcapture %}
{% capture fly_e3_v2_url1 %} .\images\{{ page.fly_e3_v2_img1 }} {% endcapture %}

{% capture fly_e3_v2_img2 %}{{page.fly_e3_v2_img2 }}{% endcapture %}
{% capture fly_e3_v2_cap2 %}{{page.fly_e3_v2_cap2 }}{% endcapture %}
{% capture fly_e3_v2_url2 %} .\images\{{ page.fly_e3_v2_img2 }} {% endcapture %}

{% capture fly_e3_v2_img3 %}{{page.fly_e3_v2_img3 }}{% endcapture %}
{% capture fly_e3_v2_cap3 %}{{page.fly_e3_v2_cap3 }}{% endcapture %}
{% capture fly_e3_v2_url3 %} .\images\{{ page.fly_e3_v2_img3 }} {% endcapture %}

Fly-E3-v2 General Information

{% include image.html file=fly_e3_v2_img1 url=fly_e3_v2_url1 alt=fly_e3_v2_cap1 caption=fly_e3_v2_cap1 %}

Overview

This page covers any general information for the Fly-E3-v2 board. It is currently available through AliExpress.

{% include tip.html content="You need to also buy the WiFi module from Mellow to be able to use RRF with this board." %}

Features

  • 32-bit ARM Cortex-M4 series 168 MHz, STM32F407ZGT6 chip
  • Supported Firmware: Marlin 2.0, Reprap, and Klipper
  • Drivers supported: A4988, LV8729, DRV8225, TMC2208, 2209, & 5160
  • Drive mode support: TMC: UART, & SPI
  • Support for 5 independent motor drives, 2 extruders, and 4 PWM fans
  • All drivers sockets support up to 24 volts.
  • Supported Displays: serial touch screen, 12864 LCD, 2004 LCD , FLY 4.3, & 7.0 V1
  • Supports automatic bed leveling sensor: BLTouch
  • Onboard CAN bus transciever.
  • Optional WiFi module supported with Reprap firmware.
  • PWM Fan MOS boards can be directly replaced in case of damage.

Driver Jumpers

The jumpers should be installed as below. “Common Interpolation” should be used for standalone drivers. “SPI mode Interpolation” is supported for TMC5160 drivers. “UART mode Interpolation” should be used when using smart drivers (i.e. TMC2208, TMC2209, TMC2225 and TMC2226)

{% include image.html file=fly_e3_v2_img2 url=fly_e3_v2_url2 alt=fly_e3_v2_cap2 caption=fly_e3_v2_cap2 %}

Driver Diag Pin

The driver diag pin is used for sensorless homing and stall detection. The Fly-E3-v2 does not have a way of disabling the diag pin as it is designed to be used with Fly-2209 drivers which have a switch on the underside of them for disabling the diag pin. If you plan on using endstops rather than sensorless homing and do not have the Fly-2209 drivers, you need to bend or remove the diag pin.

Fan Mosfets

The Fly-E3-v2 has a unique feature in that the fan mosfets are replaceable. Each mosfet (VS3622e) controls two of the fan outputs. The orientation that the fan mostfet is plugged into the board doesn't matter.

Input voltage

The board can handle an input voltage up to 32v.

Initial Installation

The board that you will receive doesn’t have any firmware installed so when plugged into a computer, the board will show as an unidentified device.

Dimensions

{% include image.html file=fly_e3_v2_img3 url=fly_e3_v2_url3 alt=fly_e3_v2_cap3 caption=fly_e3_v2_cap3 %}

{% include custom/mcu/e3v2/fly_e3_v2_links.html %}