Skip to content

Latest commit

 

History

History
118 lines (104 loc) · 4.98 KB

task_configuring_the_ontap_mediator_service_from_a_metrocluster_ip_configuration.adoc

File metadata and controls

118 lines (104 loc) · 4.98 KB
Raw
permalink sidebar keywords summary
install-ip/task_configuring_the_ontap_mediator_service_from_a_metrocluster_ip_configuration.html
sidebar
metrocluster, mediator, configure
The ONTAP Mediator service must be configured on the ONTAP node for use in a MetroCluster IP configuration.

Configure the ONTAP Mediator service from a MetroCluster IP configuration

The ONTAP Mediator service must be configured on the ONTAP node for use in a MetroCluster IP configuration.

Before you begin

  • The ONTAP Mediator must have been successfully installed on a network location that can be reached by both MetroCluster sites.

  • You must have the IP address of the host running the ONTAP Mediator service.

  • You must have the username and password for the ONTAP Mediator service.

  • All nodes of the MetroCluster IP configuration must be online.

Caution
 Beginning with ONTAP 9.12.1, you can enable the MetroCluster automatic forced switchover feature in a MetroCluster IP configuration. This feature is an extension of the Mediator-assisted unplanned switchover. Before you enable this feature, review the Risks and limitations of using MetroCluster automatic forced switchover.
About this task

  • This task enables automatic unplanned switchover by default.

  • This task can be performed on the ONTAP interface of any node in the MetroCluster IP configuration.

  • A single installation of the ONTAP Mediator service can be configured with up to five MetroCluster IP configurations.

Steps

  1. Add the ONTAP Mediator service to ONTAP:

    metrocluster configuration-settings mediator add -mediator-address ip-address-of-mediator-host

    Note
    		 You will be prompted for the username and password for the Mediator admin user account.

  2. Verify that the automatic switchover feature in enabled:

    metrocluster show

  3. Verify that the Mediator is now running.

    1. Show the Mediator virtual disks:

      storage disk show -container-type mediator

       cluster_A::> storage disk show -container-type mediator
                        Usable           Disk    Container   Container
 Disk                   Size Shelf Bay Type    Type        Name      Owner
 ---------------- ---------- ----- --- ------- ----------- --------- --------
 NET-1.5                   -     -   - VMDISK  mediator    -         node_A_2
 NET-1.6                   -     -   - VMDISK  mediator    -         node_B_1
 NET-1.7                   -     -   - VMDISK  mediator    -         node_B_2
 NET-1.8                   -     -   - VMDISK  mediator    -         node_A_1

    2. Set the privilege mode to advanced:

      set advanced

       cluster_A::> set advanced

    3. Display the initiators labelled as mediator:

      storage iscsi-initiator show -label mediator

       cluster_A::*> storage iscsi-initiator show -label mediator
   (storage iscsi-initiator show)
  +                                                                     Status
 Node Type Label    Target Portal      Target Name                      Admin/Op
 ---- ---- -------- ------------------ -------------------------------- --------
 node_A_1
      mailbox
           mediator 1.1.1.1       iqn.2012-05.local:mailbox.target.6616cd3f-9ef1-11e9-aada-00a098ccf5d8:a05e1ffb-9ef1-11e9-8f68- 00a098cbca9e:1 up/up
 node_A_2
      mailbox
           mediator 1.1.1.1       iqn.2012-05.local:mailbox.target.6616cd3f-9ef1-11e9-aada-00a098ccf5d8:a05e1ffb-9ef1-11e9-8f68-00a098cbca9e:1 up/up

    4. Verify the state of the automatic unplanned switchover (AUSO) failure domain:

      metrocluster show

      Note
      		 The following example output applies to ONTAP 9.13.1 and later. For ONTAP 9.12.1 and earlier, the AUSO failure domain state should be auso-on-cluster-disaster. 
      cluster_A::> metrocluster show
Cluster                   Entry Name          State
------------------------- ------------------- -----------
Local: cluster_A         Configuration state configured
                          Mode                normal
                          AUSO Failure Domain auso-on-dr-group-disaster
Remote: cluster_B         Configuration state configured
                          Mode                normal
                          AUSO Failure Domain auso-on-dr-group-disaster

  4. Optionally, configure MetroCluster automatic forced switchover.

    You can only use the following command in advanced privilege level.

    Important
    		 Before using this command, review the Risks and limitations of using MetroCluster automatic forced switchover.

    metrocluster modify -allow-auto-forced-switchover true

    Example
    cluster_A::*> metrocluster modify -allow-auto-forced-switchover true