pins.h

/*
    This file is part of the Repetier-Firmware for RF devices from Conrad Electronic SE.

    Repetier-Firmware is free software: you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation, either version 3 of the License, or
    (at your option) any later version.

    Repetier-Firmware is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License
    along with Repetier-Firmware.  If not, see <http://www.gnu.org/licenses/>.
*/


#ifndef PINS_H
#define PINS_H


#define CURRENT_CONTROL_DRV8711     4
#define BEEPER_PIN_RF1000           23
#define BEEPER_PIN_RF2000           5


// ##########################################################################################
// ##   RF1000 pin assignment
// ##########################################################################################
#if MOTHERBOARD == DEVICE_TYPE_RF1000
  #define KNOWN_BOARD 1

  #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif

// Definition for current control
#define STEPPER_CURRENT_CONTROL  CURRENT_CONTROL_DRV8711

// On board beeper, so define values already here
#define BEEPER_PIN              23
#define SDCARDDETECT            -1

// digital pin mappings
#define ORIG_X_STEP_PIN         54
// PINF.0, 97, STP_DRV1
#define ORIG_X_DIR_PIN          55
// PINF.1, 96, DIR_DRV1
#define ORIG_X_ENABLE_PIN       38
// PIND.7, 50, ENA_DRV1
#define ORIG_X_MIN_PIN           3
// PINE.5,  7, ES1
#define ORIG_X_MAX_PIN          -1
// not installed

#define ORIG_Y_STEP_PIN         60
// PINF.6, 91, STP_DRV2
#define ORIG_Y_DIR_PIN          61
// PINF.7, 90, DIR_DRV2
#define ORIG_Y_ENABLE_PIN       56
// PINF.2, 95, ENA_DRV2
#define ORIG_Y_MIN_PIN           2
// PINE.4,  6, ES2
#define ORIG_Y_MAX_PIN          -1
// not installed

#define ORIG_Z_STEP_PIN         46
// PINL.3, 38, STP_DRV3
#define ORIG_Z_DIR_PIN          48
// PINL.1, 36, DIR_DRV3
#define ORIG_Z_ENABLE_PIN       62
// PINK.0, 89, ENA_DRV3

// the RF1000 with miller functionality can provide min and max endstops at the same pin
#define ORIG_Z_MIN_PIN          31
// PINC.6, 59, ES3
#define ORIG_Z_MAX_PIN          31
// PINC.6, 59, ES3

#define ORIG_E0_STEP_PIN        26
// PINA.4, 74, STP_DRV4
#define ORIG_E0_DIR_PIN         28
// PINA.6, 72, DIR_DRV4
#define ORIG_E0_ENABLE_PIN      24
// PINA.2, 76, ENA_DRV4

#if NUM_EXTRUDER == 2
#define ORIG_E1_STEP_PIN        36
// PINC.1, 54, STP_DRV5
#define ORIG_E1_DIR_PIN         34
// PINC.3, 56, DIR_DRV5
#define ORIG_E1_ENABLE_PIN      30
// PINC.7, 60, ENA_DRV5
#else
#define ORIG_E1_STEP_PIN        -1
#define ORIG_E1_DIR_PIN         -1
#define ORIG_E1_ENABLE_PIN      -1
#endif // NUM_EXTRUDER == 2

#define SDPOWER                 -1
#define SDSS                    53
// PINB.0, 19, SS
#define LED_PIN                 13
// PINB.7, 26, LED13

#if PROTOTYPE_PCB == 1 // 1 = first PCB's / 0 = Final
  #define ORIG_FAN_PIN          25
// PINA.3, 75, OUT1
#else
  #define ORIG_FAN_PIN          27
// PINA.5, 73, OUT2
#endif

#define WATCHDOG_PIN            37
// PINC.0

#define HEATER_0_PIN            10
// PINB.4, 23, HZ1  left X4

#if NUM_EXTRUDER == 2
#define HEATER_1_PIN             9
// PINH.6, 18, HZ2  right X8
#else
#define HEATER_1_PIN            -1
#endif // NUM_EXTRUDER == 2

#define HEATER_2_PIN             8
// PINH.5, 17, HZ3

// analog pin mappings
#define TEMP_0_PIN              13
// PINK.5, 84, TH1  X5
#define TEMP_1_PIN              14
// PINK.6, 83, TH2  X6
#define TEMP_2_PIN              15
// PINK.7, 82, TH3

#define E0_PINS                 ORIG_E0_STEP_PIN, ORIG_E0_DIR_PIN, ORIG_E0_ENABLE_PIN,
#define E1_PINS                 ORIG_E1_STEP_PIN, ORIG_E1_DIR_PIN, ORIG_E1_ENABLE_PIN,

// these pins are defined in the SD library if building with SD support
#define SCK_PIN                 52
// PINB.1, 20, SCK
#define MISO_PIN                50
// PINB.3, 22, MISO
#define MOSI_PIN                51
// PINB.2, 21, MOSI
#define MAX6675_SS              53
// PINB.0, 19, SS

// motor driver pin mappings
#define X_SCS_PIN               49
// PINL.0, 35, SCS_1
#define X_STALL_PIN             41
// PING.0, 51, STALLn_1

#define Y_SCS_PIN               47
// PINL.2, 37, SCS_2
#define Y_STALL_PIN             40
// PING.1, 52, STALLn_2

#define Z_SCS_PIN               45
// PINL.4, 39, SCS_3
#define Z_STALL_PIN             39
// PING.2, 70, STALLn_3

#define O0_SCS_PIN              43
// PINL.6, 41, SCS_4
#define O0_STALL_PIN            95
// PING.3, 28, STALLn_4

#define O1_SCS_PIN              84
// PINJ.7, 79, SCS_5
#define O1_STALL_PIN            96
// PING.4, 29, STALLn_5

#define DRV_FAULT               97
// PINE.6, 8, FAULTn
#define DRV_RESET1              90
// PINE.7, 9, RESET_DRV
#define DRV_SCLK                93
// PIND.5, 48, SCLK
#define DRV_SDATO               92
// PIND.4, 47, SDATO
#define DRV_SDATI               94
// PIND.6, 49, SDATI

// key pin mappings
#define ENABLE_KEY_E1           80
// PINJ.2, 65, TAST_E1
#define ENABLE_KEY_E2           81
// PINJ.4, 67, TAST_E2
#define ENABLE_KEY_E3           82
// PINJ.5, 68, TAST_E3
#define ENABLE_KEY_E4           83
// PINJ.6, 69, TAST_E4
#define ENABLE_KEY_E5           85
// PINH.7, 27, TAST_E5
#define ENABLE_KEY_E6           86
// PINH.2, 14, TAST_E6
#define ENABLE_KEY_1             4
// PING.5,  1, TAST1
#define ENABLE_KEY_2             5
// PINE.3,  5, TAST2
#define ENABLE_KEY_3             6
// PINH.3, 15, TAST3
#define ENABLE_KEY_4            11
// PINB.5, 24, TAST4
#define ENABLE_KEY_5            42
// PINL.7, 42, TAST5

// servo pin mapping
#define SERVO0_PIN              35
// PINC.2, 55, PC2
#define SERVO1_PIN              33
// PINC.4, 57, PC4
#define SERVO2_PIN              32
// PINC.5, 58, PC5

// case light pin mapping
#define CASE_LIGHT_PIN          25
// PINA.3, 75, OUT1

// case fan pin mapping
#define CASE_FAN_PIN             9
// PINH.6, 18, HZ2

// display pin mapping
#define UI_DISPLAY_RS_PIN       63
// PINK.1, 88, D_RS
#define UI_DISPLAY_RW_PIN       -1
#define UI_DISPLAY_ENABLE_PIN   65
// PINK.3, 86, D_E
#define UI_DISPLAY_D0_PIN       -1
#define UI_DISPLAY_D1_PIN       -1
#define UI_DISPLAY_D2_PIN       -1
#define UI_DISPLAY_D3_PIN       -1
#define UI_DISPLAY_D4_PIN       59
// PINF.5, 92, D_D4
#define UI_DISPLAY_D5_PIN       64
// PINK.2, 87, D_D5
#define UI_DISPLAY_D6_PIN       44
// PINL.5, 40, D_D6
#define UI_DISPLAY_D7_PIN       66
// PINK.4, 85, D_D7

#define OUTPUT_230V_PIN         -1
#define FET1                    -1
#define FET2                    -1
#define FET3                    -1

//http://www.rf1000.de/viewtopic.php?f=24&t=1119 :
//RF1000 X25.12 und RF2000 X33.3 //Serial3 RX3
#define RESERVE_DIGITAL_PIN_PJ0 15
//RF1000 X25.13 und RF2000 X33.4 //Serial3 TX3
#define RESERVE_DIGITAL_PIN_PJ1 14 

//X25.4
#define RESERVE_DIGITAL_PIN_PC2 35 
//X25.5
#define RESERVE_DIGITAL_PIN_PC4 33 
//X25.6
#define RESERVE_DIGITAL_PIN_PC5 32 

//X25.7
#define RESERVE_DIGITAL_PIN_PD2 19
//RF1000 X25.8 und RF2000 X34.2 "EXT_IRQ"/INT3 -> FEATURE_USER_INT3
#define RESERVE_DIGITAL_PIN_PD3 18 

//X25.10
#define RESERVE_ANALOG_PIN_PF3 3 
//X25.11
#define RESERVE_ANALOG_PIN_PF4 4 

//#define RESERVE_DIGITAL_PIN_PE2  //X25.9 -> kein digital pin? XCK0/AIN0 ? HW Pin 4
//#define RESERVE_DIGITAL_PIN_PC0 -> //X25.3 Doppelfunktion! s. Reset & Watchdog
//#define RESERVE_DIGITAL_PIN_PB6 -> //X25.2 Doppelfunktion! s. Heizplatte


#endif // MOTHERBOARD == DEVICE_TYPE_RF1000


// ##########################################################################################
// ##   RF2000 pin assignment
// ##########################################################################################
#if MOTHERBOARD == DEVICE_TYPE_RF2000
  #define KNOWN_BOARD 1

  #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif

// Definition for current control
#define STEPPER_CURRENT_CONTROL  CURRENT_CONTROL_DRV8711

// On board beeper, so define values already here
#define BEEPER_PIN               5
// PINE.3,  5, BUZ1
#define SDCARDDETECT            19
// PIND.2, 45, CARD

// digital pin mappings
#define ORIG_X_STEP_PIN         54
// PINF.0, 97, STP_DRV1
#define ORIG_X_DIR_PIN          55
// PINF.1, 96, DIR_DRV1
#define ORIG_X_ENABLE_PIN       38
// PIND.7, 50, ENA_DRV1
#define ORIG_X_MIN_PIN          35
// PINC.2, 55, ES1
#define ORIG_X_MAX_PIN          -1
// not installed

#define ORIG_Y_STEP_PIN         60
// PINF.6, 91, STP_DRV2
#define ORIG_Y_DIR_PIN          61
// PINF.7, 90, DIR_DRV2
#define ORIG_Y_ENABLE_PIN       56
// PINF.2, 95, ENA_DRV2
#define ORIG_Y_MIN_PIN          37
// PINC.0, 53, ES2
#define ORIG_Y_MAX_PIN          -1
// not installed

#define ORIG_Z_STEP_PIN         57
// PINF.3, 94, STP_DRV3
#define ORIG_Z_DIR_PIN          48
// PINL.1, 36, DIR_DRV3
#define ORIG_Z_ENABLE_PIN       62
// PINK.0, 89, ENA_DRV3

// the RF2000 with miller functionality can provide min and max endstops
#define ORIG_Z_MIN_PIN          31
// PINC.6, 59, ES3
#define ORIG_Z_MAX_PIN          16
// PINH.1, 13, ES4

#define ORIG_E0_STEP_PIN        26
// PINA.4, 74, STP_DRV4
#define ORIG_E0_DIR_PIN         28
// PINA.6, 72, DIR_DRV4
#define ORIG_E0_ENABLE_PIN      24
// PINA.2, 76, ENA_DRV4

#define ORIG_E1_STEP_PIN        36
// PINC.1, 54, STP_DRV5
#define ORIG_E1_DIR_PIN         34
// PINC.3, 56, DIR_DRV5
#define ORIG_E1_ENABLE_PIN      30
// PINC.7, 60, ENA_DRV5

#define SDPOWER                 -1
#define SDSS                    53
// PINB.0, 19, SS
#define LED_PIN                 -1

#define ORIG_FAN_PIN            27
// PINA.5, 73, OUT2

#define WATCHDOG_PIN            29
// PINA.7, 71, WDI

#define HEATER_0_PIN            10
// PINB.4, 23, HZ1
#define HEATER_1_PIN             9
// PINH.6, 18, HZ2
#define HEATER_2_PIN            91
// PINE.2,  4, HZ3

// analog pin mappings
#define TEMP_0_PIN              13
// PINK.5, 84, TH1
#define TEMP_1_PIN              14
// PINK.6, 83, TH2
#define TEMP_2_PIN              15
// PINK.7, 82, TH3
#define TEMP_3_PIN              12
// PINK.4, 85, TH4

#define E0_PINS                 ORIG_E0_STEP_PIN, ORIG_E0_DIR_PIN, ORIG_E0_ENABLE_PIN,
#define E1_PINS                 ORIG_E1_STEP_PIN, ORIG_E1_DIR_PIN, ORIG_E1_ENABLE_PIN,

// these pins are defined in the SD library if building with SD support
#define SCK_PIN                 52
// PINB.1, 20, SCK
#define MISO_PIN                50
// PINB.3, 22, MISO
#define MOSI_PIN                51
// PINB.2, 21, MOSI
#define MAX6675_SS              53
// PINB.0, 19, SS

// motor driver pin mappings
#define X_SCS_PIN               49
// PINL.0, 35, SCS_1
#define X_STALL_PIN             41
// PING.0, 51, STALLn_1

#define Y_SCS_PIN               47
// PINL.2, 37, SCS_2
#define Y_STALL_PIN             40
// PING.1, 52, STALLn_2

#define Z_SCS_PIN               12
// PINB.6, 25, SCS_3
#define Z_STALL_PIN             39
// PING.2, 70, STALLn_3

#define O0_SCS_PIN              43
// PINL.6, 41, SCS_4
#define O0_STALL_PIN            95
// PING.3, 28, STALLn_4

#define O1_SCS_PIN              84
// PINJ.7, 79, SCS_5
#define O1_STALL_PIN            96
// PING.4, 29, STALLn_5

#define DRV_FAULT               97
// PINE.6,  8, FAULTn
#define DRV_RESET1              90
// PINE.7,  9, RESET_DRV
#define DRV_SCLK                93
// PIND.5, 48, SCLK
#define DRV_SDATO               92
// PIND.4, 47, SDATO
#define DRV_SDATI               94
// PIND.6, 49, SDATI

// key pin mappings
#define ENABLE_KEY_E1           80
// PINJ.2, 65, TAST_E1
#define ENABLE_KEY_E2           81
// PINJ.4, 67, TAST_E2
#define ENABLE_KEY_E3           82
// PINJ.5, 68, TAST_E3
#define ENABLE_KEY_E4           83
// PINJ.6, 69, TAST_E4
#define ENABLE_KEY_E5           85
// PINH.7, 27, TAST_E5
#define ENABLE_KEY_E6           86
// PINH.2, 14, TAST_E6
#define ENABLE_KEY_1             4
// PING.5,  1, TAST1
#define ENABLE_KEY_2            13
// PINB.7, 26, TAST2
#define ENABLE_KEY_3            17
// PINH.0, 12, TAST3
#define ENABLE_KEY_4            11
// PINB.5, 24, TAST4
#define ENABLE_KEY_5            42
// PINL.7, 42, TAST5

// servo pin mapping
#define SERVO1_PIN              46
// PINL.3, 38, SERVO_1
#define SERVO2_PIN              45
// PINL.4, 39, SERVO_2
#define SERVO3_PIN              44
// PINL.5, 40, SERVO_3

// 230V output pin mapping
#define OUTPUT_230V_PIN         3
// PINE.5,  7, P230

// 3x 24V FET output pin mapping
#define FET1                    33
// PINC.4, 57, OUT3
#define FET2                    32
// PINC.5, 58, OUT4
#define FET3                    58
// PINF.4, 93, OUT5

// RGB lights pin mapping
#define RGB_LIGHT_R_PIN         6
// PINH.3, 15, L_RT
#define RGB_LIGHT_G_PIN         7
// PINH.4, 16, L_GN
#define RGB_LIGHT_B_PIN         8
// PINH.5, 17, L_BL

// case light pin mapping
#define CASE_LIGHT_PIN          25
// PINA.3, 75, OUT1

// case fan pin mapping
#define CASE_FAN_PIN            58
// PINF.4, 93, OUT5

// display pin mapping
#define UI_DISPLAY_RS_PIN       63
// PINK.1, 88, D_RS
#define UI_DISPLAY_RW_PIN       -1
#define UI_DISPLAY_ENABLE_PIN   65
// PINK.3, 86, D_E
#define UI_DISPLAY_D0_PIN       -1
#define UI_DISPLAY_D1_PIN       -1
#define UI_DISPLAY_D2_PIN       -1
#define UI_DISPLAY_D3_PIN       -1
#define UI_DISPLAY_D4_PIN       59
// PINF.5, 92, D_D4
#define UI_DISPLAY_D5_PIN       64
// PINK.2, 87, D_D5
#define UI_DISPLAY_D6_PIN       23
// PINA.1, 77, D_D6
#define UI_DISPLAY_D7_PIN       98
// PINJ.3, 66, D_D7

// debug pin mapping (added with RF1.39)
// PINJ.0, 63, PJ0
#define DEBUG_TEST_J0_PIN       15 

//RF spare pins:
//RF1000 X25.12 und RF2000 X33.3 //Serial3 RX3
#define RESERVE_DIGITAL_PIN_PJ0 15 
//RF1000 X25.13 und RF2000 X33.4 //Serial3 TX3
#define RESERVE_DIGITAL_PIN_PJ1 14 
//RF2000 X33.5 used for FEATURE_READ_CALIPER data input as example.
#define RESERVE_DIGITAL_PIN_PE4 2 
//RF1000 X25.8 und RF2000 X34.2 "EXT_IRQ"/INT3 -> FEATURE_USER_INT3/FEATURE_READ_CALIPER
#define RESERVE_DIGITAL_PIN_PD3 18 
/* X34.3=SCL und X34.4=SDA ist I²C siehe wire.h. (X34.1=5V und X34.5/X34.6=VSS) An diesem Bus sind auch die DMS und EEPROMs für Geräteidentifikation (EEPROM 2) und das EEPROM für die Z-Matrix (EEPROM 1) angeschlossen. */
#endif // MOTHERBOARD == DEVICE_TYPE_RF2000


// ##########################################################################################
// ##	RF2000v2 pin assignment
// ##########################################################################################
#if MOTHERBOARD == DEVICE_TYPE_RF2000v2
  #define KNOWN_BOARD 1

  #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
  #endif

// Definition for current control
#define STEPPER_CURRENT_CONTROL  CURRENT_CONTROL_DRV8711

// On board beeper, so define values already here
// PINE.3,  5, BUZ1
#define BEEPER_PIN		 		 5
// PIND.2, 45, CARD
#define SDCARDDETECT			19

// digital pin mappings
// PINF.0, 97, STP_DRV1
#define ORIG_X_STEP_PIN         54
// PINF.1, 96, DIR_DRV1
#define ORIG_X_DIR_PIN          55
// PIND.7, 50, ENA_DRV1
#define ORIG_X_ENABLE_PIN       38
// PINC.2, 55, ES1
#define ORIG_X_MIN_PIN          35
// not installed
#define ORIG_X_MAX_PIN          -1

// PINF.6, 91, STP_DRV2
#define ORIG_Y_STEP_PIN         60
// PINF.7, 90, DIR_DRV2
#define ORIG_Y_DIR_PIN          61
// PINF.2, 95, ENA_DRV2
#define ORIG_Y_ENABLE_PIN       56
// PINC.0, 53, ES2
#define ORIG_Y_MIN_PIN          37
// not installed
#define ORIG_Y_MAX_PIN          -1

// PINF.3, 94, STP_DRV3
#define ORIG_Z_STEP_PIN         57
// PINL.1, 36, DIR_DRV3
#define ORIG_Z_DIR_PIN          48
// PINK.0, 89, ENA_DRV3
#define ORIG_Z_ENABLE_PIN       62

// the RF2000 with miller functionality can provide min and max endstops
// PINC.6, 59, ES3
#define ORIG_Z_MIN_PIN          31
// PINH.1, 13, ES4
#define ORIG_Z_MAX_PIN          16

// PINA.4, 74, STP_DRV4
#define ORIG_E0_STEP_PIN        26
// PINA.6, 72, DIR_DRV4
#define ORIG_E0_DIR_PIN         28
// PINA.2, 76, ENA_DRV4
#define ORIG_E0_ENABLE_PIN      24

// PINC.1, 54, STP_DRV5
#define ORIG_E1_STEP_PIN        36
// PINC.3, 56, DIR_DRV5
#define ORIG_E1_DIR_PIN         34
// PINC.7, 60, ENA_DRV5
#define ORIG_E1_ENABLE_PIN      30

#define SDPOWER				    -1
// PINB.0, 19, SS
#define SDSS				    53
#define LED_PIN				    -1

// PINA.5, 73, OUT2
#define ORIG_FAN_PIN			27

// PINA.7, 71, WDI
#define WATCHDOG_PIN		    29

// PINB.4, 23, HZ1
#define HEATER_0_PIN		    10
// PINH.6, 18, HZ2
#define HEATER_1_PIN		     9
// PINE.2,  4, HZ3
#define HEATER_2_PIN		    91

// analog pin mappings
// PINK.5, 84, TH1
#define TEMP_0_PIN			    13
// PINK.6, 83, TH2
#define TEMP_1_PIN			    14
// PINK.7, 82, TH3
#define TEMP_2_PIN			    15
// PINK.4, 85, TH4
#define	TEMP_3_PIN				12

#define E0_PINS					ORIG_E0_STEP_PIN, ORIG_E0_DIR_PIN, ORIG_E0_ENABLE_PIN,
#define E1_PINS					ORIG_E1_STEP_PIN, ORIG_E1_DIR_PIN, ORIG_E1_ENABLE_PIN,

// these pins are defined in the SD library if building with SD support
// PINB.1, 20, SCK
#define SCK_PIN				    52
// PINB.3, 22, MISO
#define MISO_PIN			    50
// PINB.2, 21, MOSI
#define MOSI_PIN			    51
// PINB.0, 19, SS
#define MAX6675_SS				53

// motor driver pin mappings
// PINL.0, 35, SCS_1
#define X_SCS_PIN			    49
// PING.0, 51, STALLn_1
#define X_STALL_PIN			    41

// PINL.2, 37, SCS_2
#define Y_SCS_PIN			    47
// PING.1, 52, STALLn_2
#define Y_STALL_PIN			    40

// PINB.6, 25, SCS_3
#define Z_SCS_PIN			    12
// PING.2, 70, STALLn_3
#define Z_STALL_PIN			    39

// PINL.6, 41, SCS_4
#define O0_SCS_PIN			    43
// PING.3, 28, STALLn_4
#define O0_STALL_PIN		    95

// PINJ.7, 79, SCS_5
#define O1_SCS_PIN			    84
// PING.4, 29, STALLn_5
#define O1_STALL_PIN		    96

// PINE.6,  8, FAULTn
#define	DRV_FAULT			    97
// PINE.7,  9, RESET_DRV
#define DRV_RESET1			    90
// PIND.5, 48, SCLK
#define DRV_SCLK			    93
// PIND.4, 47, SDATO
#define DRV_SDATO			    92
// PIND.6, 49, SDATI
#define DRV_SDATI			    94

// key pin mappings
// PINJ.2, 65, TAST_E1
#define ENABLE_KEY_E1		    80
// PINJ.4, 67, TAST_E2
#define ENABLE_KEY_E2		    81
// PINJ.5, 68, TAST_E3
#define ENABLE_KEY_E3		    82
// PINJ.6, 69, TAST_E4
#define ENABLE_KEY_E4		    83
// PINH.7, 27, TAST_E5
#define ENABLE_KEY_E5		    85
// PINH.2, 14, TAST_E6
#define ENABLE_KEY_E6		    86
// PING.5,  1, TAST1
#define ENABLE_KEY_1			 4
// PINB.7, 26, TAST2
#define ENABLE_KEY_2			13
// PINH.0, 12, TAST3
#define ENABLE_KEY_3			17
// PINB.5, 24, TAST4
#define ENABLE_KEY_4			11
// PINL.7, 42, TAST5
#define ENABLE_KEY_5			42

// servo pin mapping
// PINL.3, 38, SERVO_1
#define SERVO1_PIN				46
// PINL.4, 39, SERVO_2
#define SERVO2_PIN				45
// PINL.5, 40, SERVO_3
#define SERVO3_PIN				44

// 230V output pin mapping
// PINE.5,  7, P230
#define OUTPUT_230V_PIN			3

// 3x 24V FET output pin mapping
// PINC.4, 57, OUT3
#define FET1					33
// PINC.5, 58, OUT4
#define	FET2					32
// PINF.4, 93, OUT5
#define	FET3					58

// RGB lights pin mapping
// PINH.3, 15, L_RT
#define RGB_LIGHT_R_PIN			6
// PINH.4, 16, L_GN
#define RGB_LIGHT_G_PIN			7
// PINH.5, 17, L_BL
#define RGB_LIGHT_B_PIN			8

// case light pin mapping
// PINA.3, 75, OUT1
#define CASE_LIGHT_PIN			25

// case fan pin mapping
// PINF.4, 93, OUT5
#define	CASE_FAN_PIN			58

// display pin mapping
// PINK.1, 88, D_RS
#define UI_DISPLAY_RS_PIN		63
#define UI_DISPLAY_RW_PIN		-1
// PINK.3, 86, D_E
#define UI_DISPLAY_ENABLE_PIN	65
#define UI_DISPLAY_D0_PIN		-1
#define UI_DISPLAY_D1_PIN		-1
#define UI_DISPLAY_D2_PIN		-1
#define UI_DISPLAY_D3_PIN		-1
// PINF.5, 92, D_D4
#define UI_DISPLAY_D4_PIN		59
// PINK.2, 87, D_D5
#define UI_DISPLAY_D5_PIN		64
// PINA.1, 77, D_D6
#define UI_DISPLAY_D6_PIN		23
// PINJ.3, 66, D_D7
#define UI_DISPLAY_D7_PIN		98

// debug pin mapping
// PINJ.0, 63, PJ0
#define DEBUG_TEST_J0_PIN		15

//RF spare pins:
//RF1000 X25.12 und RF2000 X33.3 //Serial3 RX3
#define RESERVE_DIGITAL_PIN_PJ0 15 
//RF1000 X25.13 und RF2000 X33.4 //Serial3 TX3
#define RESERVE_DIGITAL_PIN_PJ1 14
//RF2000 X33.5 used for FEATURE_READ_CALIPER data input as example.
#define RESERVE_DIGITAL_PIN_PE4 2 
//RF1000 X25.8 und RF2000 X34.2 "EXT_IRQ"/INT3 -> FEATURE_USER_INT3/FEATURE_READ_CALIPER
#define RESERVE_DIGITAL_PIN_PD3 18 
/* X34.3=SCL und X34.4=SDA ist I²C siehe wire.h. (X34.1=5V und X34.5/X34.6=VSS) An diesem Bus sind auch die DMS und EEPROMs für Geräteidentifikation (EEPROM 2) und das EEPROM für die Z-Matrix (EEPROM 1) angeschlossen. */
#endif // MOTHERBOARD == DEVICE_TYPE_RF2000v2



#ifndef SDSSORIG
#define SDSSORIG                -1
#endif

#ifndef FAN_BOARD_PIN
#define FAN_BOARD_PIN           -1
#endif

#if NUM_EXTRUDER==1
#undef E1_PINS
#define E1_PINS
#endif

#if NUM_EXTRUDER<=2
#undef E2_PINS
#define E2_PINS
#endif

#ifndef HEATER_PINS_INVERTED
#define HEATER_PINS_INVERTED    0
#endif

// Original pin assignmats to be used in configuration tool
#define X_STEP_PIN              ORIG_X_STEP_PIN
#define X_DIR_PIN               ORIG_X_DIR_PIN
#define X_ENABLE_PIN            ORIG_X_ENABLE_PIN
#define X_MIN_PIN               ORIG_X_MIN_PIN
#define X_MAX_PIN               ORIG_X_MAX_PIN

#define Y_STEP_PIN              ORIG_Y_STEP_PIN
#define Y_DIR_PIN               ORIG_Y_DIR_PIN
#define Y_ENABLE_PIN            ORIG_Y_ENABLE_PIN
#define Y_MIN_PIN               ORIG_Y_MIN_PIN
#define Y_MAX_PIN               ORIG_Y_MAX_PIN

#define Z_STEP_PIN              ORIG_Z_STEP_PIN
#define Z_DIR_PIN               ORIG_Z_DIR_PIN
#define Z_ENABLE_PIN            ORIG_Z_ENABLE_PIN
#define Z_MIN_PIN               ORIG_Z_MIN_PIN
#define Z_MAX_PIN               ORIG_Z_MAX_PIN

#define E0_STEP_PIN             ORIG_E0_STEP_PIN
#define E0_DIR_PIN              ORIG_E0_DIR_PIN
#define E0_ENABLE_PIN           ORIG_E0_ENABLE_PIN

#define E1_STEP_PIN             ORIG_E1_STEP_PIN
#define E1_DIR_PIN              ORIG_E1_DIR_PIN
#define E1_ENABLE_PIN           ORIG_E1_ENABLE_PIN

#define E2_STEP_PIN             ORIG_E2_STEP_PIN
#define E2_DIR_PIN              ORIG_E2_DIR_PIN
#define E2_ENABLE_PIN           ORIG_E2_ENABLE_PIN

#define FAN_PIN                 ORIG_FAN_PIN
#define FAN2_PIN                ORIG_FAN2_PIN

#endif
// PINS_H