-
Notifications
You must be signed in to change notification settings - Fork 7
/
ReleaseNotes.txt
101 lines (82 loc) · 3.11 KB
/
ReleaseNotes.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
/********************************************************/
version 2.x.3.4:
features
Fit TTN and LoRaServer at region CN470 to connected quickly.
/********************************************************/
version 2.x.3.3:
features
Adjust duty cycle to improve the user experience
/********************************************************/
version 2.x.3.2:
features
This version is based on 2.x.3.1.
1.Fix a debug about "The Hard Fault exception occurs,Reset!".
2.The end number in version indicate the version with DEBUG or RELEASE :odd:DEBUG ,even:RELEASE.
/********************************************************/
version 2.x.3.1:
features
1.This version combine HF and LF board firmware of RAK811. Through defined macro 'LORA_HF_BOARD' surpport HF,or undefined to surpport LF.
2.The Release or Debug Mode switch by modifying the macro 'DEBUG_FW' in "rw_sys.h" to be '0' or '1'.
/********************************************************/
version 2.x.3.0:
features
1. Adapt to Actility test.
2. Fix the problem that the device can't send commands after sending at+sleep
3. Integrate all bands and use the at+band command to switch regional bands.
4.The meaning of x in version number:0 support regions:EU868, US915, AU915, KR920, AS923,IN865,CN779.
1 support regions:EU433,CN470.
/********************************************************/
version 2.0.2.2:
features
1. update LoraWAN 1.0.1 to LoraWAN 1.0.2, support regions:
EU868, US915, AU915, KR920, AS923, IN865
2. Add Peripheral command
at+rd_reg=<reg_addr>[,<len>]
at+wr_reg=<reg_addr>,<len>,<databuf>
at+gpio=<pin>[,<level>]
at+rd_adc=<pin>
at+rd_iic=<dev_addr>,<data_addr>[,<len>]
at+wr_iic=<dev_addr>,<data_addr>,<databuf>
3. add config class to select loraWAN class A C
4. add at+recv_ex command to enable rssi snr with recv
5. add at+link_cnt to get up/downlink counter
6. add at+abp_info to get abp info after join OTAA successfully
7. add at+set_config parameters.
bugs
1. fix P2P frequence 868-929.9 MHz
2. fix at+recv data bug
/********************************************************/
version 1.0.2.6:
features
1. add at+band command to get the loraWAN region info.
2. open EU868 channel 0-2 to customer redefined.
3. change EU868 duty cycle config to disenable.
4. add at+dr command to change the send datarate temporary.
bugs
1. fix at+set_config=rx2:datarate,frequency
2. fix at+uart return info
3. fix at+set_config=dr:datarate use to change the default datarate
/********************************************************/
version 1.0.2.3:
features
1. sleep power consumption fix to 7.2uA
bugs
/********************************************************/
version 1.0.2.2:
features
bugs
1. fix at+txc cnts change limits 100 to 65535
2. fix bug data flash abnormal to factory config
/********************************************************/
version 1.0.1.4:
features
bugs
1. fix rx_delay1 setting
2. fix join abp way to load new config
/********************************************************/
version 1.0.1.2:
features
1. add LoraP2P interfaces
version 1.0.1.0:
1. support LoraWAN V1.0.1 ClassA
2. fixed some bugs, release first version