New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
STEVAL-IDP004V1 (master-board) either not communicating to PC through RS485 or not detecting a sensor out of the box #2
Comments
Hi, [>> TX] START SELECT MASTER OR DEVICE [>> TX] MASTER [>> TX] 0 [>> TX] WR_S [>> TX] 096,248,033,122,122,122,122, [>> TX] COMMAND END [>> TX] DEVICE [>> TX] 0 [>> TX] IDS [>> TX] COMMAND END |
Dear Pranav, We are very pleased with the interest you show to our products. In case you found an issue in the user manual, it is always worth reporting it. It helps us enhance the quality of our documents and we do thank you for that. However, this public organization on GitHub is intended to promote co-development and issues posted here shall exclusively be related to the software published within the different repositories. For any other issue (e.g. related to documentation, to hardware, to ecosystem, etc.), you shall address your questions to the ST Community. There you shall look for the adequate topic and submit your question or remark. As for the issue you posted here, allow us to close it now. Thank you for your understanding. We hope you keep on enjoying using our products and look forward to receiving further issues and pull-request from you (once pull-requests become accepted). With regards, |
@ALABSTM Main issues are :
Can you please forward my notest to developement/support team? Best Regards |
Dear Pranav, I will try to. Hopefully you get the answers you are expecting to these setbacks you are facing. With regards, |
@ALABSTM Kind Regards |
@ALABSTM Best Regards |
Hello Pranav, Ali is currently out of office. Let me try to help you. As proposed by Ali, you can ask your question to the ST Community forum (https://community.st.com/s/) Hope this will help you |
Hello Christophe Please help. |
Hello Christophe Best Regards |
Hello Pranav. |
Okay- thanks. Kind Regards |
Hi Pranav, As this issue is now handled at On-Line Support level, allow me to close it. Thank you for your comprehension. With regards, |
Hi,
We have recently purchased the STEVAL-BFA001V1B kit and planned to connect the STEVAL-IDP004V1 to the STEVAL-IDP005V1 as we planned to use the STEVAL-IDP004V1 GUI interface to allow for streaming off data from the sensor.
The manuals we have used are:
https://www.st.com/content/ccc/resource/sales_and_marketing/presentation/product_presentation/group0/47/a2/91/a0/fe/ca/42/89/steval-bfa001v1b_getting_started_guide/files/steval-bfa001v1b_quick_start_guide.pdf/jcr:content/translations/en.steval-bfa001v1b_quick_start_guide.pdf
https://www.avnet.com/opasdata/d120001/medias/docus/190/STEVAL-BFA001V1B%20User%20Manual.pdf
They make reference to updating the firmware of the STEVAL-IDP005V1 through dragging across "STEVAL-IDP005_ConditionMonitoring_IOL_v1.1.0.bin." The GUI after doing this results in the following error:
"[>> TX] START
[ERR] Command ERROR (TRASMISSION FAIL) - RECEIVED DATA
[>> TX] COMMAND END
[ERR] Command ERROR (TRASMISSION FAIL) - RECEIVED DATA
[ERR] Communication with STEVAL-IDP004V1 BOARD failed.
The 2nd manual refers to disconnect the assembly that we tried with no hope of any differences.
The STEVAL-IDP004V1 itself has 4 green flashes lights for each sensor (sensor 1, sensor 2 and so fourth) that has not changed implying that the sensor (STEVAL-IDP005V1) is not detected as a sensor.
Additionally, we are unable to determine whether there is any communication between the STEVAL-IDP004V1 and the PC.
We have uploaded another project (Condition_Monitoring_SRV) through the System Workbench by running/debugging and then connected through putty which following a reset of the STEVAL-IDP005V1 means data is streamed from the sensor.
Please help.
Thank you.
Best Regards
Pranav Mondhe
The text was updated successfully, but these errors were encountered: