| ABAUD |
Set the Primary serial port baud rate |
| ALIAS1 |
Set the digipeater alias callsign with SSID |
| ALIAS2 |
Set the digipeater alias callsign with SSID |
| ALIAS3 |
Set the digipeater alias callsign with SSID |
| ALTNET |
Set and alternative network destination |
| AMODE |
Set the Primary serial port mode [ KISS , TEXT , GPS , DEAFTEXT ] |
| BANK |
Set the current bank used for options |
| BBAUD |
Set the Secondary serial port baud rate |
| BMODE |
Set the Secondary serial port mode [ KISS , TEXT , GPS , DEAFTEXT ] |
| BNKMODE |
Set the current bank switching mode |
| BPERIOD |
Set the beacon period in seconds |
| BTEXT |
Set the beacon text |
| CALIBRATE |
Calibrate transmit audio level |
| CDLEVEL |
Set the Carrier Detect Level (applicable to Audio Level and Audio Tone methods) |
| CDMODE |
Set the Carrier Detect Mode |
| COPY |
Copy options to other bank |
| DDIST |
Set to display distance to stations on LCD |
| DEC96 |
Set to decode 9600 baud packet rather than 1200 baud packet |
| DECSTAT |
Set to display decoding stats |
| DIGIID |
Set Digipeater to replace digipeater callsign with MYCALL |
| DIGIMY |
Set to digipeat when MYCALL in path |
| DISPLAY |
Display all option values and commands |
| DMETRIC |
Set to display metric on the LCD |
| DMSDISP |
Set to display seconds (DD MM'SS") instead of decimal minutes (DD MM.mmmm) |
| DUPETIME |
Set the digipeater alias callsign with SSID |
| ENTS |
Set the use of Time Slotting (use TSOFFSET) |
| EXPORT |
Display all option values in a way that can be parsed |
| FILTERCALL |
Set the callsign to filter match |
| FRAWDISP |
Set to disable display packet parsing |
| GALT |
Set the default location altitude |
| GKRELAY |
Set the GPS KISS Relay ID (0 = disabled) |
| GPSCHK |
Set to validate checksums on incoming GPS sentences |
| GRELAYBITS |
Set the GPS Text Relay Sentence Type Bits |
| GRELAYRATE |
Set the GPS Text Relay Rate (0 = disabled) |
| GWAYLEN |
Set the GPS Waypoint output name length |
| GWAYMODE |
Set the GPS Waypoint mode |
| HEADERLN |
Set to send a new line between headers and content |
| HELP |
Display help for all options and commands |
| HRAWDISP |
Set to hide unparsed packets from display |
| INTCLK |
Set to internal only clock (not GPS based) |
| LEDS |
Set to enable LEDs |
| LOCATION |
Set the default location (in the form ddmm.mmmmx dddmm.mmmmx |
| LRNTPS |
Set to make the TPS time auto-learning |
| MICETMV |
Set to transmit MIC-E format including type, manufacturer, and version |
| MMSG |
Set the tracker MIC-E Message number |
| MONITOR |
Monitor incoming audio level |
| MPPERIOD |
Set the tracker manual position report period in seconds |
| MSGCAP |
Set to show message capable in APRS Text position reports |
| MSGCMD |
Set to parse commands in messages |
| MTXD |
Set the Manual Packet Transmit delay time in bytes (about 7ms each at 1200 baud) |
| MYCALL |
Set the Packet source (user) callsign with SSID |
| NODISP |
Set to disable the display (which enables digital telemetry) |
| P300 |
Set the Packet module to send 300 baud (rather than 1200 baud) |
| PASSTHRU |
Pass serial between ports |
| PATH1 |
Set the outgoing digi path first callsign |
| PATH2 |
Set the outgoing digi path second callsign |
| PATH3 |
Set the outgoing digi path third callsign |
| PAVPEN |
Set to enable PAVP mode |
| PERSIST |
Set the Packet persist value. (0 to 255, higher is more likely to transmit) |
| PKTICOM |
Set to send decoded packets to computer TEXT and KISS ports |
| PKTOCOM |
Set to send generated packets to computer TEXT and KISS ports |
| PPATHING |
Set to enable proportional pathing |
| PPERIOD |
Set the tracker position report period in seconds |
| PREEMPT |
Set Preemptive Digipeating |
| QUIET |
Set the Packet delay after carrier detect drops before a transmission can occur (in 100ms units) |
| QUIT |
Quit the options menu |
| RESTORE |
Restore default factory settings |
| RPATHDISP |
Set to show path for raw packet display |
| RXAMP |
Set the Packet receive audio amplifier |
| RXFREQ |
Set the Receive Frequency |
| RXSQUELCH |
Set the Receive Squelch Level |
| SBEN |
Set to enable tracker SmartBeaconing (Use other SB commands to configure) |
| SBFPERIOD |
Set the tracker SmartBeaconing Fast Period (Use TSB to enable) |
| SBFSPEED |
Set the tracker SmartBeaconing Fast Speed (Use TSB to enable) |
| SBSPERIOD |
Set the tracker SmartBeaconing Slow Period (Use TSB to enable) |
| SBSSPEED |
Set the tracker SmartBeaconing Slow Speed (Use TSB to enable) |
| SBTANGLE |
Set the tracker SmartBeaconing Turn Angle Speed (Use TSB to enable) |
| SBTSLOPE |
Set the tracker SmartBeaconing Turn Slope (Use TSB to enable) |
| SBTTIME |
Set the tracker SmartBeaconing Turn Time (Use TSB to enable) |
| SLOTTIME |
Set the Packet slot time |
| SOFTRST |
Set to allow software reset via serial |
| SSIDROUTE |
Set the SSID routing mode |
| STATUSRATE |
Set the tracker Status Rate (0 for never, uses the TSTATUS) |
| TALT |
Set the tracker to send altitude, if available |
| TDAO |
Set the tracker !DAO! resolution (0 for disabled, 1 for 1 extra digit, 2 for 2 extra digits) |
| TELHIRES |
Set telemetry to send high-res data (0..999 rather than 0..255) |
| TELREAD |
Set telemetry to send temp and voltage in readable form |
| TELTEMP |
Set telemetry to send the temperature |
| TELVOLT |
Set telemetry to send the supply voltage |
| TIMEHMS |
Set the tracker to send a timestamp in Hour, Minute, Second format (rather than Day, Hour, Minute) |
| TIMESTAMP |
Set the tracker to send a timestamp (format defined by TIMEHMS) |
| TOSV |
Set the tracker to only send valid position reports |
| TPERIOD |
Set the telemetry report period in seconds |
| TPROTOCOL |
Set the tracker output protocol (MIC-E, APRS Text, Compressed) |
| TPSWITCH |
Set the tracker Power Switch Time |
| TRNKMODE |
Set the Trunking Mode |
| TSOFFSET |
Set the tracker Time Slot Offset (Use ENTS to enable) |
| TSPEED |
Set the tracker to send speed and heading |
| TSTAT |
Set the tracker status text |
| TSWPT |
Set the tracker to output a GPS waypoint of self when position is transmitted |
| TSYMCODE |
Set the tracker Symbol code character |
| TSYMTABLE |
Set the tracker Symbol table or overlay |
| TTEMPTWK |
Set the telemetry report period in seconds |
| TVOLTTWK |
Set the telemetry report period in seconds |
| TXD |
Set the Packet Transmit delay time in bytes (about 7ms each at 1200 baud) |
| TXFREQ |
Set the Transmit Frequency |
| TXLEVEL |
Set the Packet transmit audio level (0 .. 128) |
| TXTDISP |
Set to display sent incoming serial text |
| TXTWIST |
Set the Packet transmit audio twist (0 = all low tone, 50 = even tone levels, 100 = all high tone) |
| WPERIOD |
Set the weather report period in seconds |
| WXPOS |
Set weather reports to include position |
| WYPTXT |
Set to send waypoints to TEXT ports in addition to GPS ports |