printer-20230330_205753.cfg

# MKS Gen l V1
########################################
# Includes
########################################
[include mainsail.cfg]
[include macros.cfg]
[include neopixel.cfg]

########################################
# Printer configuration
########################################
[mcu]
serial:/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0

[printer]
kinematics: cartesian
max_velocity: 250
max_accel: 2000
max_z_velocity: 25
max_z_accel: 120
square_corner_velocity: 10.0

# [virtual_sdcard]
# path: ~/gcode_files

########################################
# Stepper Motor configuration
########################################

[stepper_x]
step_pin: PF0
dir_pin: !PF1
enable_pin: !PD7
microsteps: 16
rotation_distance: 40   ##rotation_distance = ((360°/1.8°) * microsteps) / 80 # # 旋转距离 = （圆周360°/步距角）*细分/每MM脉冲值
endstop_pin:^!PE5 #X-Min, PE4:X-Max
position_endstop: -6
position_min: -6
position_max: 310
homing_speed: 60

[stepper_y]
step_pin: PF6
dir_pin: !PF7
enable_pin: !PF2
microsteps: 16
rotation_distance: 40
endstop_pin: ^!PJ1  #Y-Min, PJ0:Y-Max
position_endstop: -20
position_min: -20
position_max: 310
homing_speed: 60

[stepper_z]
step_pin: PL3
dir_pin: PL1
enable_pin: !PK0
microsteps: 16
rotation_distance: 8
# endstop_pin: ^!PD3  #Z-Min, PD2:Z-Max
endstop_pin: probe:z_virtual_endstop
position_max: 300
position_min: -8
homing_speed: 8

[extruder]
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
microsteps: 16
rotation_distance: 7.64
gear_ratio: 3:1
nozzle_diameter: 0.4
filament_diameter: 1.750
heater_pin: PB4
sensor_type: ATC Semitec 104GT-2
sensor_pin: PK5
min_temp: 0
max_temp: 285
#control: pid
#pid_Kp: 22.2
#pid_Ki: 1.08
#pid_Kd: 114

#[extruder1]
#step_pin: PC1
#dir_pin: !PC3
#enable_pin: !PC7
#heater_pin: PH4
#sensor_pin: PK7
#...

########################################
# TMC UART configuration
########################################
[tmc2208 stepper_x]
uart_pin: PK1
# tx_pin aka the pin with the 1K resistor
tx_pin: PG1
run_current: 0.600
stealthchop_threshold: 260

[tmc2208 stepper_y]
uart_pin: PK2
# tx_pin aka the pin with the 1K resistor
tx_pin: PF5
run_current: 0.600
stealthchop_threshold: 260

[tmc2208 stepper_z]
uart_pin: PK3
# tx_pin aka the pin with the 1K resistor
tx_pin: PL7
run_current: 0.800
stealthchop_threshold: 30

[tmc2208 extruder]
uart_pin: PK4
# tx_pin aka the pin with the 1K resistor
tx_pin: PL5
run_current: 0.700
stealthchop_threshold: 30

# [tmc2208 stepper_e1]
# uart_pin: PB6
# tx_pin aka the pin with the 1K resistor
# tx_pin: PD1
# run_current: 0.600
# stealthchop_threshold: 30

########################################
# Probe/Mesh configuration
########################################
[probe]
pin:  ^!PD3
#z_offset: 0
speed: 5.0
x_offset: -45
y_offset: -8

[bed_mesh]
speed: 100
horizontal_move_z: 5
mesh_min:15,5
mesh_max:255,265
probe_count: 5,5
relative_reference_index: 12
mesh_pps: 2,2
fade_start: 1
fade_end: 10
fade_target: 0

# [homing_override]
# set_position_z: 15
# axes: z
# gcode:
#     G90
#     BED_MESH_CLEAR
#     G1 Z30 F480
#     G28 X0 Y0
#     G1 X150 Y150 F3600
#     G28 Z0
#     G1 Z50 F480

[safe_z_home]
home_xy_position: 150,150 # Change coordinates to the center of your print bed
speed: 50
z_hop: 10                 # Move up 10mm
z_hop_speed: 5

[force_move]
enable_force_move: true

########################################
# Bed configuration
########################################
[heater_bed]
heater_pin: PH5
sensor_type: ATC Semitec 104GT-2
sensor_pin: PK6
min_temp: 0
max_temp: 130
control: pid
pid_Kp: 325.10
pid_Ki: 63.35
pid_Kd: 417.10

########################################
# Fan configuration
########################################
[fan]
pin: PH6

[heater_fan extruder_fan]
pin: PH4
heater: extruder
heater_temp: 50.0

########################################
# Display configuration
########################################
[display]
lcd_type: st7920
cs_pin: PH1
sclk_pin: PA1
sid_pin: PH0
encoder_pins: ^PC6, ^PC4
click_pin: ^!PC2
kill_pin: ^!EXP2_8
menu_root: __main
menu_timeout: 40

[output_pin beeper]
pin: EXP1_1
pwm: True
value: 0
shutdown_value: 0
cycle_time: 0.001
scale: 1000

[display_status]

 
########################################
# EXP1 / EXP2 (display) pins
########################################

[board_pins]
aliases:
    # EXP1 header
    EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
    EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
    # EXP2 header
    EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0,  EXP2_9=<GND>,
    EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<NC>
    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp1"
# See the MKS Lcd Config path file for definitions of common LCD displays.

[pause_resume]

#[bltouch]
#sensor_pin: ^PD2
#control_pin:PB5
#x_offset: -44
#y_offset: -14
#z_offset: 3.099
#speed: 10.0
#samples: 2
#samples_result: median
#sample_retract_dist: 3.0
#samples_tolerance: 0.1
#samples_tolerance_retries: 1

[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE
gcode:
  TURN_OFF_HEATERS
  CANCEL_PRINT_BASE


[gcode_macro G29]
gcode:
    BED_MESH_CLEAR
    G28
    BED_MESH_CALIBRATE
    BED_MESH_PROFILE SAVE=name
    SAVE_CONFIG
    BED_MESH_PROFILE LOAD=name

# Gcode for clearing the display
[delayed_gcode clear_display]
gcode:
    M117

# Gcode executed when the printer is ready
[delayed_gcode on_ready]
initial_duration: 1
gcode:
    SET_IDLE_TIMEOUT TIMEOUT=2400
    M117 Tornado Ready
    UPDATE_DELAYED_GCODE ID=clear_display DURATION=10

# Fake macros to avoid warnings
[gcode_macro SNAP]
gcode:

[gcode_macro UNLOAD_FILAMENT]
gcode:
    SAVE_GCODE_STATE NAME=UNLOAD_FILAMENT_state
    M83
    G1 E-100 F1000
    RESTORE_GCODE_STATE NAME=UNLOAD_FILAMENT_state

[gcode_macro LOAD_FILAMENT]
gcode:
    SAVE_GCODE_STATE NAME=LOAD_FILAMENT_state
    M83
    G1 E50 F1000
    G1 E50 F300
    G1 E100 F300
    RESTORE_GCODE_STATE NAME=LOAD_FILAMENT_state

[gcode_macro PRIME_FILAMENT]
gcode:
    SAVE_GCODE_STATE NAME=PRIME_FILAMENT_state
    M83
    G1 E100 F300
    RESTORE_GCODE_STATE NAME=PRIME_FILAMENT_state

[gcode_macro PARK]
gcode:
	{% set X = params.X|default(8)|float %}
	{% set Y = params.Y|default(27)|float %}
	{% set Z = params.Z|default(20)|float %}
    SAVE_GCODE_STATE NAME=PARK_state
    G91
    G1 E-2.0 F3000
    G1 Z{Z}
    G90
    G1 X{X} Y{Y} F3000
    RESTORE_GCODE_STATE NAME=PARK_state

[gcode_macro CHANGE_FILAMENT]
variable_enabled: 0
gcode:
    {% if printer["gcode_macro CHANGE_FILAMENT"].enabled %}
        PAUSE
        PARK
        G91
        G1 E-100 F1000
        M117 Change Filament
        PLAY_ANNOYING_BEEPS
    {% endif %}
    SET_GCODE_VARIABLE MACRO=CHANGE_FILAMENT VARIABLE=enabled VALUE=0

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	0.220000, 0.080000, -0.017500, 0.020000, 0.125000
#*# 	0.212500, 0.065000, -0.032500, -0.010000, 0.107500
#*# 	0.207500, 0.092500, 0.000000, 0.030000, 0.107500
#*# 	0.202500, 0.105000, 0.020000, 0.045000, 0.145000
#*# 	0.202500, 0.137500, 0.090000, 0.115000, 0.205000
#*# tension = 0.2
#*# min_x = 15.0
#*# algo = lagrange
#*# y_count = 5
#*# mesh_y_pps = 2
#*# min_y = 5.0
#*# x_count = 5
#*# max_y = 265.0
#*# mesh_x_pps = 2
#*# max_x = 255.0
#*#
#*# [bed_mesh name]
#*# version = 1
#*# points =
#*# 	0.052500, -0.032500, 0.186250
#*# 	0.053750, -0.070000, 0.233750
#*# 	0.182500, 0.037500, 0.240000
#*# tension = 0.2
#*# min_x = 20.0
#*# algo = lagrange
#*# y_count = 3
#*# mesh_y_pps = 2
#*# min_y = 50.0
#*# x_count = 3
#*# max_y = 200.0
#*# mesh_x_pps = 2
#*# max_x = 170.0
#*#
#*# [probe]
#*# z_offset = 2.000
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 27.823
#*# pid_ki = 3.254
#*# pid_kd = 59.471