大神还是有问题，以上午脚本启动的passwall表面上是启动了，但是不能用 #353
Replies: 21 comments
-
|
每跑一次，都得进后台，重新点 |
Beta Was this translation helpful? Give feedback.
-
|
因为不清楚你的路由器里的 passwall 具体启动命令是什么，昨天远程协助我只是找了找系统服务，当时你也没测试。 |
Beta Was this translation helpful? Give feedback.
-
|
想想咋办，大神，要不不完美 |
Beta Was this translation helpful? Give feedback.
-
|
我又加了定时任务，你的脚本用行完十分钟后重启路由，虽然方法笨点，然后发现还是不行，一看passwall居然没启动 |
Beta Was this translation helpful? Give feedback.
-
|
00 5 * * * sleep 5 && touch /etc/banner && reboot |
Beta Was this translation helpful? Give feedback.
-
|
好像可以的，有些糊涂 |
Beta Was this translation helpful? Give feedback.
-
|
你这越说越迷糊。 你是想重新改回上次的方案？（即定时重启路由器，启动 CloudflareST，延迟启动 passwall） |
Beta Was this translation helpful? Give feedback.
-
|
改进现在方案，现在这个方案是有问题的，脚本跑完后，passwall是正常启动，但在等域名解析生效后，就需要进路由器后台，重新点保存并应用 |
Beta Was this translation helpful? Give feedback.
-
|
跑完脚本后，前几分钟可以正常使用。隔几分钟后就无法使用了，只能在路由器里点一下保存和应用，具体原因不清楚 |
Beta Was this translation helpful? Give feedback.
-
|
我只是怀疑和动态域名解析有关，域名解析间隔，是十分钟 |
Beta Was this translation helpful? Give feedback.
-
如果你不需要在其他设备、网络下单独使用你的代理，那么连 DDNS 的步骤都能省掉。 |
Beta Was this translation helpful? Give feedback.
-
|
我怀疑是不是需要重启v2ray |
Beta Was this translation helpful? Give feedback.
-
|
路由器里的保存和应用，和你代码控制，肯定有区别 |
Beta Was this translation helpful? Give feedback.
-
|
但问题是我不知道相应的命令呀。 |
Beta Was this translation helpful? Give feedback.
-
|
不是ttl问题，如果是缓存，那不应该断才对，现在是不在路由器里点保存与应用，就完全不能用 |
Beta Was this translation helpful? Give feedback.
-
|
你能不能在脚本里，后面再加个重启v2ray命令， |
Beta Was this translation helpful? Give feedback.
-
|
我不是万能的。 你用的代理工具都依托于 passwall，都由 passwall 控制。 |
Beta Was this translation helpful? Give feedback.
-
|
一个是每次脚本测速完，加个 hosts，把域名都指向最快 IP，而 Hosts 是立即生效的。，要不，用这个办法试试 |
Beta Was this translation helpful? Give feedback.
-
|
那就远程协助吧，希望这是最后一次。。。 |
Beta Was this translation helpful? Give feedback.
-
|
xiangrikui |
Beta Was this translation helpful? Give feedback.
-
还得进路由器，点保存&应用，才能使用，唉，要不然就完美了
Beta Was this translation helpful? Give feedback.
All reactions