printer.cfg

[include fluidd.cfg]
[virtual_sdcard]
path: /home/661wls/printer_data/gcodes
on_error_gcode: CANCEL_PRINT

# TASKS:
# - Add macro to park on idle timeout/shutdown/reset
# - Add MCU and driver temp sensing if possible... https://klipper.discourse.group/t/ebb42-stm32-temperature/8709

# This file contains config used for my V1 Engineering MP3DP v4 Repeat build:
# - Config : {
#   - Usable : { X : 250, Y : 250, Z : 250 },
#   - Controller : BTT Octopus v1.1
#     - EndStops : PG6, PG9, PG10, PG11, PG12, PG13, PG14, PG15
#   - CanBus-Expansion : BTT EBB36-v1.2,
#     - MAX31865 SPI 1 : { CS : PA4, SCLK : PA5, MISO: PA6, MOSI : PA7 }
#     - ADXL345 SPI 2 : { CS : PB12, SCLK : PB10, MISO : PB2, MOSI : PB11 }
#   - Extruder-HotEnd : BIQU H2 V2S Revo Extruder
#     - Thermistor Type : Semitec 104NT-4-R025H42G(NTC100K)
#   - Prob : ANTCLABS BLTouch Auto Bed Leveling Sensor v3.1
#     - Wiring info @ https://www.antclabs.com/wiring
#     - Reusing probe bought ~2020/12, there's probably newer/better ones now...
# }

# Content is based on BTT's generic-bigtreetech-octopus.cfg template, and info
# from various specs, as well as Klipper and V1E forum members with similar, but
# different builds (e.g. gpagnozzi and probrwr have Manta M8B controllers with 
# diff pins).

# 0         1         2         3         4         5         6         7
# 01234567890123456789012345678901234567890123456789012345678901234567890123456789

# Related:
# - See docs/Config_Reference.md for a description of parameters.
# - https://www.klipper3d.org/Config_Reference.html
# - https://github.com/bigtreetech/BIGTREETECH-OCTOPUS-V1.0/blob/master/Firmware/Klipper/generic-bigtreetech-octopus.cfg
# - https://github.com/VoronDesign/Voron-Trident/blob/main/Firmware/Octopus/Trident_Octopus_Config.cfg
# - EBB36 Pinout diagram https://github.com/bigtreetech/EBB/blob/master/EBB%20CAN%20V1.1%20(STM32G0B1)/EBB36%20CAN%20V1.1/Hardware/EBB36%20CAN%20V1.1%26V1.2-PIN.png
# - gpagnozzi's printer.cfg for his V1E MP3DP v4 build, see https://forum.v1e.com/t/mp3dp-v4-build-sw-virginia/37238/31?u=azab2c
# - probrwr's printer.cfg for his V1E MP3DP v4 build, see https://forum.v1e.com/t/mp3dp-v4-build-sw-virginia/37238/104?u=azab2c

[include mainsail.cfg]


[skew_correction]


#[force_move]
#enable_force_move: False
#   Set to true to enable FORCE_MOVE and SET_KINEMATIC_POSITION
#   extended G-Code commands. The default is false.

# Driver0
[stepper_x]
enable_pin: !PF14
step_pin: PF13
dir_pin: PF12
endstop_pin: EBBCan: PB6
microsteps: 16
rotation_distance: 32 #AZA Was 40
position_endstop: 0
position_max: 250
homing_speed: 100
second_homing_speed: 3

# Driver1
[stepper_y]
enable_pin: !PF15
step_pin: PG0
dir_pin: PG1
endstop_pin: PG6 
microsteps: 16
rotation_distance: 32 #AZA was 40
position_endstop: 0
position_max: 250
homing_speed: 100
second_homing_speed: 3

## Driver2
[stepper_z]
enable_pin: !PG5
step_pin: PF11
dir_pin: PG3
microsteps: 16
rotation_distance: 32
endstop_pin: probe:z_virtual_endstop
# position_endstop: 0
position_max: 260
position_min: -5.0
homing_speed: 40
second_homing_speed: 3
homing_retract_dist: 10

[stepper_z1]
enable_pin: !PA0
step_pin: PG4
dir_pin: PC1
microsteps: 16
rotation_distance: 32
endstop_pin: probe:z_virtual_endstop
#position_endstop: 0

[stepper_z2]
enable_pin: !PG2
step_pin: PF9
dir_pin: PF10
microsteps: 16
rotation_distance: 32
endstop_pin: probe:z_virtual_endstop
#position_endstop: 0

#[manual_stepper man_step_z]
#enable_pin: !PG5
#step_pin: PF11
#dir_pin: PG3
#microsteps: 16
#rotation_distance: 32
#velocity:
#   Set the default velocity (in mm/s) for the stepper. This value
#   will be used if a MANUAL_STEPPER command does not specify a SPEED
#   parameter. The default is 5mm/s.
#accel:
#   Set the default acceleration (in mm/s^2) for the stepper. An
#   acceleration of zero will result in no acceleration. This value
#   will be used if a MANUAL_STEPPER command does not specify an ACCEL
#   parameter. The default is zero.
#endstop_pin:
#   Endstop switch detection pin. If specified, then one may perform
#   "homing moves" by adding a STOP_ON_ENDSTOP parameter to
#   MANUAL_STEPPER movement commands.


# FUTURES:
#[filament_switch_sensor material_0] ...
#[filament_switch_sensor material_1] ...
#[filament_switch_sensor material_2] ...
#[filament_switch_sensor material_3] ...


# Based on :
# - https://docs.vorondesign.com/community/howto/samwiseg0/btt_smart_filament_sensor.html
[filament_motion_sensor SFS_T0]
detection_length: 10.00 # This can be adjusted to your desired level of sensitivity. 10 is a recomended value to prevent flow dropoff false triggers.
extruder: extruder
switch_pin: ^PG12
pause_on_runout: True # This can be set to false to debug false positives putting the sensor in "monitor mode". The printer will not pause but it will run the runout_gcode below. 
event_delay: 3.0
pause_delay: 0.5
runout_gcode:
    M117 Filament Runout/Jamb!
insert_gcode:
    M117 Filament Inserted...

[delayed_gcode DISABLEFILAMENTSENSOR] ; This will disable the SFS 1 second after klipper starts
initial_duration: 1
gcode:
    SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=0 ; Put your filament sensor's name after SENSOR=

[gcode_macro SFS_ENABLE] ; Add this to PRINT_START
description: Enable smart filament sensor
gcode:
    M117 ENABLING the Smart Filament Sensor
    G92 E0
    SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=1 ; Put your filament sensor's name after SENSOR=

[gcode_macro SFS_DISABLE] ; Add this to PRINT_END and PRINT_CANCEL
description: Disable smart filament sensor 
gcode:
    M117 DISABLING the Smart Filament Sensor
    G92 E0
    SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=0 ; Put your filament sensor's name after SENSOR=


########################################
# EXTRUDER
########################################


[extruder] # https://www.klipper3d.org/Config_Reference.html#extruder
step_pin: EBBCan: PD0
dir_pin: !EBBCan: PD1
enable_pin: !EBBCan: PD2
heater_pin: EBBCan: PB13  # V1.2 = PB13, V1.1 = PA2
microsteps: 16
rotation_distance: 3.484 #3.433 #gpagnozzi TODO:???
nozzle_diameter: 0.400
filament_diameter: 1.750

# Related:
# - https://www.klipper3d.org/Config_Reference.html#maxxxxxx-temperature-sensors
sensor_type: ATC Semitec 104NT-4-R025H42G
sensor_pin: EBBCan: PA3 # TH0 connector

# - Use MAX31865 For PT100 (100 Ohm) or PT1000 (1000 Ohm) Platinum based Temp sensors. 
# - Do *NOT* use MAX31865 for NTC100K (100,000 Ohm).  
#   - Mentioning because of this topic... https://klipper.discourse.group/t/start-config-failure-thermocouple-reader-fault-using-max31865-on-ebb36-v1-2-with-biqu-h2-v2s-revo-extruder/8629
#   - With compatible sensors, MAX31865 will provide reliable, precise, stable temperature sensing, details @ https://www.adafruit.com/product/3328
#sensor_type: MAX31865
#sensor_pin: EBBCan: PA4
#spi_software_sclk_pin: EBBCan: PA5
#spi_software_miso_pin: EBBCan: PA6
#spi_software_mosi_pin: EBBCan: PA7
#rtd_nominal_r: 100
#rtd_reference_r: 430
#rtd_num_of_wires: 2

#probrwr sensor_type: ATC Semitec 104NT-4-R025H42G # BIQU H2S Spec sheet says "Semitec 104NT-4-R025H42G(NTC100K)"  #Generic 3950 #EPCOS 100K B57560G104F
#control: watermark # pid  # TODO:P0 Figure out what to use for control and pid* settings ... e.g. control: pid ? 
#pid_Kp: 21.527
#pid_Ki: 1.063
#pid_Kd: 108.982
min_temp: 0
max_temp: 270
min_extrude_temp: 0
pressure_advance: 0.0375 #AZA TODO: Figure out what value to use.  Default = pressure_advance = 0


########################################
# MCUs
########################################


[mcu]
canbus_uuid: 642f53509351  #AZA found via  python3 ~/CanBoot/scripts/flash_can.py -q
#[mcu]
#serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_2A0005001850344D30353320-if00
#serial: /dev/ttyS0
#serial: /dev/ttyAMA0
# restart_method: command  #AZA commented because of https://github.com/Arksine/CanBoot/issues/72#issuecomment-1502495476

[mcu EBBCan] #AZA
canbus_uuid: f7a5fa2b8bf6 #AZA
#baud: 500000  #AZA baud: attribute not valid here 🤷‍♂️, will error with "Invalid Config"

[printer]
# Related
# - gpagnozzi experienced ghosting at 10000, see https://forum.v1e.com/t/mp3dp-repeat-v3-to-v4-1-upgrade/38096/17?u=azab2c 
kinematics: corexy
max_velocity: 800 # default: 300
max_accel: 7000 #AZA default: 3000
max_accel_to_decel: 3500
max_z_velocity: 200 # default: 5
max_z_accel: 200 # default: 100
square_corner_velocity: 4.5

########################################
# Bed Heater
########################################

[heater_bed]
# Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
# Use "Generic 3950" for Keenovo heaters
heater_pin: PA3 #AZA Originally tried PA1 but didn't observe any power to SSR input.
sensor_pin: PF3 # TB
##AZA: From Voron...  Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 .
#max_power: 0.6 ##AZA

# sensor_type: Generic 3950 #AZA Using https://www.amazon.com/gp/product/B07GJDL7XB with NTC 100K 3950 thermistor,  Old: ATC Semitec 104GT-2   
sensor_type: EPCOS 100K B57560G104F #AZA
#control: pid
#pid_Kp: 54.027
#pid_Ki: 0.770
#pid_Kd: 948.182


min_temp: 0  #AZA HACKHACK should be 0
max_temp: 130 #AZA HACKHACK should be 120 or 130 most

########################################
# Bed Mesh
########################################

# https://www.klipper3d.org/Config_Reference.html?h=pixel#bed-level-support
[bed_mesh]
speed: 100
horizontal_move_z: 8
mesh_min: 25, 25
mesh_max: 220, 210 # Bed max size minus probe X/Y offset
probe_count: 5,5
algorithm: bicubic #lagrange
mesh_pps: 4, 4 #1, 1
bicubic_tension: .5 #.5
move_check_distance: 5 #10
split_delta_z: .025
fade_start: 1
fade_end: 10
fade_target: 0

########################################
# Fan
########################################

[fan]
pin: EBBCan: PA1  # FAN2
#AZA was... pin: PA8

[heater_fan hotend_fan]
pin: EBBCan: PA0  # FAN1
heater: extruder
heater_temp: 50.0

#[heater_fan fan1]
#pin: PE5

#[heater_fan fan2]
#pin: PD12

#[heater_fan fan3]
#pin: PD13

#[heater_fan fan4]
#pin: PD14

#[controller_fan fan5]
#pin: PD15


########################################
# EBB Sensors / Actuators
########################################

[input_shaper]
shaper_freq_x: 75.8
shaper_type_x: mzv
shaper_freq_y: 75.8
shaper_type_y: mzv

# probrwr's [input_shaper]
#[input_shaper]
#shaper_freq_x: 106.8
#shaper_type_x: zv
#shaper_freq_y: 55.6
#shaper_type_y: mzv



[adxl345]
cs_pin: EBBCan: PB12
spi_software_sclk_pin: EBBCan: PB10
spi_software_mosi_pin: EBBCan: PB11
spi_software_miso_pin: EBBCan: PB2
axes_map: x,z,y

[resonance_tester]
accel_chip: adxl345
probe_points: 150, 150, 30

[bltouch]
sensor_pin: ^EBBCan: PB8
control_pin: EBBCan: PB9
x_offset: -25 #AZA based on probrwr's adapter
y_offset: -34
z_offset: 1.2 #AZA 2023-09-09 Was... 1.55
#x_offset: 0
#y_offset: -25
#z_offset: 3.35  #AZA ???
speed: 7.5
samples: 2
sample_retract_dist: 10.0
stow_on_each_sample: True #AZA False saves time between probes, but risk hitting/damaging Probe.  Only use if confident breakage risk is low...
probe_with_touch_mode: True

[led status_led]
green_pin: EBBCan: PA13
cycle_time: 4.0
initial_GREEN: 0.5


########################################
# BED Sensors / Actuators
########################################

[safe_z_home]
home_xy_position: 125, 125
speed: 50
#z_hop: 30

[z_tilt] #AZA TODO:P1 Rough est, should this be more precise?  See trident, and ref doc @ https://www.klipper3d.org/Config_Reference.html?h=pixel#z_tilt
z_positions: -20, 27
  135, 303
  292, 27

#center_Y186
points: 30, 55
  30, 240
  245, 240
  245, 55
#points: 25, 55
#  150, 240
#  245, 55

speed: 150
horizontal_move_z: 10
retries: 4
retry_tolerance: 0.4 #0.04

[bed_screws] 
# AZA configured bed_screws based on my setup...
# - Bed (PEI-Magnetic) 250x250
# - Alu plate 260x260
# - Heater 235x235 https://www.amazon.com/gp/product/B07GJDL7XB
#  - Center of screw hole are 32.5mm from silicone heater edge
screw1: 37.5, 37.5
screw2: 37.5, 222.5
screw3: 222.5, 222.5
screw4: 222.5, 37.5

#[filament_switch_sensor switch_sensor]
#switch_pin: EBBCan:PB4


########################################
# FIRMWARE RETRACTION
########################################
[firmware_retraction]
retract_length: 0.2
retract_speed: 20  #AZA probrwr uses 40

########################################
# Bling
########################################

#[neopixel hotend_rgb]
#pin: EBBCan:PD3

########################################
# TMC2209 configuration
# - Set uart_pin to CS pin, per pinout diag
########################################

[tmc2209 extruder]
uart_pin: EBBCan: PA15
run_current: 0.650
stealthchop_threshold: 999999

[tmc2209 stepper_x]
uart_pin: PC4
##diag_pin: PG6
run_current: 0.7 #AZA was 0.8
interpolate: False  #AZA Why??? Default True, but gpagnozzi False (note his is Manta M8P not Octopus), see https://www.klipper3d.org/Config_Reference.html?h=pixel#tmc2209 and https://forum.v1e.com/t/mp3dp-v4-build-sw-virginia/37238/31?u=azab2c
#stealthchop_threshold: 999999

[tmc2209 stepper_y]
uart_pin: PD11
##diag_pin: PG9
run_current: 0.7 #AZA was 0.8
interpolate: False
#stealthchop_threshold: 999999

[tmc2209 stepper_z]
uart_pin: PC6
##diag_pin: PG10
run_current: 0.7
interpolate: False
#stealthchop_threshold: 999999

[tmc2209 stepper_z1]
uart_pin: PC7
##diag_pin: PG11
run_current: 0.7
interpolate: False
#stealthchop_threshold: 999999

[tmc2209 stepper_z2]
uart_pin: PF2
##diag_pin: PG12
run_current: 0.7
interpolate: False
#stealthchop_threshold: 999999

# driver 5 : uart_pin: PE4
# driver 6 : uart_pin: PE1
# driver 7 : PD3


[board_pins]
aliases:
    # EXP1 header
    EXP1_1=PE8, EXP1_2=PE7,
    EXP1_3=PE9, EXP1_4=PE10,
    EXP1_5=PE12, EXP1_6=PE13,    # Slot in the socket on this side
    EXP1_7=PE14, EXP1_8=PE15,
    EXP1_9=<GND>, EXP1_10=<5V>,

    # EXP2 header
    EXP2_1=PA6, EXP2_2=PA5,
    EXP2_3=PB1, EXP2_4=PA4,
    EXP2_5=PB2, EXP2_6=PA7,      # Slot in the socket on this side
    EXP2_7=PC15, EXP2_8=<RST>,
    EXP2_9=<GND>, EXP2_10=PC5

# See the sample-lcd.cfg file for definitions of common LCD displays.

# A [probe] section can be defined instead with a pin: setting identical
# to the sensor_pin: for a bltouch
#[bltouch]
#sensor_pin: PB7
#control_pin: PB6
#z_offset: 0

#[neopixel my_neopixel]
#pin: PB0


#############################
# MACROS
#############################
[idle_timeout]
timeout: 900
gcode:
  TURN_OFF_HEATERS
  
  # Turn off bed, extruder, and fan
  M140 S0
  M104 S0
  M106 S0
  
  # Ensure skew compensation turned off
  SET_SKEW CLEAR=1
  
  # Move to safe position
  G1 X245 Y245 Z230 F7000
  
  # Disable steppers
  M84

 

[gcode_macro move_safe]
description: Move to safe Z position so bed doesn't crash on reset.
gcode:
  G0 Z220 F6000



[gcode_macro PAUSE]
description: Pause the actual running print
rename_existing: PAUSE_BASE
gcode:
  PAUSE_BASE
  _TOOLHEAD_PARK_PAUSE_CANCEL


[gcode_macro RESUME]
description: Resume the actual running print
rename_existing: RESUME_BASE
gcode:
  ##### read extrude from  _TOOLHEAD_PARK_PAUSE_CANCEL  macro #####
  {% set extrude = printer['gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL'].extrude %}
  #### get VELOCITY parameter if specified ####
  {% if 'VELOCITY' in params|upper %}
    {% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
  {%else %}
    {% set get_params = "" %}
  {% endif %}
  ##### end of definitions #####
  {% if printer.extruder.can_extrude|lower == 'true' %}
    M83
    G1 E{extrude} F2100
    {% if printer.gcode_move.absolute_extrude |lower == 'true' %} M82 {% endif %}
  {% else %}
    {action_respond_info("Extruder not hot enough")}
  {% endif %}  
  RESUME_BASE {get_params}



[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE
variable_park: True
gcode:
  ## Move head and retract only if not already in the pause state and park set to true
  {% if printer.pause_resume.is_paused|lower == 'false' and park|lower == 'true'%}
    _TOOLHEAD_PARK_PAUSE_CANCEL
  {% endif %}
  TURN_OFF_HEATERS
  CANCEL_PRINT_BASE
  SFS_DISABLE


[gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL]
description: Helper: park toolhead used in PAUSE and CANCEL_PRINT
variable_extrude: 1.0
gcode:
  ##### set park positon for x and y #####
  # default is your max posion from your printer.cfg
  {% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
  {% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
  {% set z_park_delta = 2.0 %}
  ##### calculate save lift position #####
  {% set max_z = printer.toolhead.axis_maximum.z|float %}
  {% set act_z = printer.toolhead.position.z|float %}
  {% if act_z < (max_z - z_park_delta) %}
    {% set z_safe = z_park_delta %}
  {% else %}
    {% set z_safe = max_z - act_z %}
  {% endif %}
  ##### end of definitions #####
  {% if printer.extruder.can_extrude|lower == 'true' %}
    M83
    G1 E-{extrude} F2100
    {% if printer.gcode_move.absolute_extrude |lower == 'true' %} M82 {% endif %}
  {% else %}
    {action_respond_info("Extruder not hot enough")}
  {% endif %}
  {% if "xyz" in printer.toolhead.homed_axes %}
    G91
    G1 Z{z_safe} F900
    G90
    G1 X{x_park} Y{y_park} F6000
    {% if printer.gcode_move.absolute_coordinates|lower == 'false' %} G91 {% endif %}
  {% else %}
    {action_respond_info("Printer not homed")}
  {% endif %}


######################################
# Start GCode
######################################


[gcode_macro START_PRINT]
gcode:    

      #Get Bed and Extruder temperature from Slicer GCode
      #{% set BED_TEMP = params.BED_TEMP| default|}
      #{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP| defaut|}
      {% set BED_TEMP = params.BED_TEMP|default(60)|float %}
      {% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(205)|float %}
      #Preheat nozzle and bed
      M104 S{EXTRUDER_TEMP} T0                        
      M140 S{BED_TEMP}                                

      # Use absolute coordinates
      G90

      #Home
      G28 X Y 
      G28 Z F4800

      SFS_ENABLE

      Z_TILT_ADJUST #[<probe_parameter>=<value>]
      
      #Use defaut bed mesh
      BED_MESH_PROFILE LOAD=default_25


      #Heat nozzle and bed
      M190 S{BED_TEMP}                               
      M109 S{EXTRUDER_TEMP} T0                       

      #Precondition extruder
      G92 E0              
      G1 Z2.0 F600        
      G1 Z0.2 F600        
      G1 Z2.0 F600

      #Prime line
      PRIME_LINE

      # Load and set skew profile created per https://www.klipper3d.org/Skew_Correction.html#take-your-measurements
      SKEW_PROFILE LOAD=skew_profile_1

      M117 Printing...

######################################
# Prime line
######################################

[gcode_macro PRIME_LINE]
gcode: 
    M117 Prime Line
    G92 E0 ;Reset Extruder
    # move z axis 
    G1 Z3.6 F3000 ;Move Z Axis up
    # move to prime position 
    G1 X5 Y85 Z2 F5000.0 ;Move to start position
    G1 X5 Y200.0 Z0.35 F1500.0 E15 ;Draw the first line
    G1 X7 Y200.0 Z0.35 F5000.0 ;Move to side a little
    G1 X7 Y85 Z0.35 F1500.0 E30 ;Draw the second line
    G92 E0 ;Reset Extruder
    G1 Z4.0 F3000 ;Move Z Axis up

######################################
# End Gcode
######################################

[gcode_macro END_PRINT]
gcode:
    SET_SKEW CLEAR=1

    SFS_DISABLE

    # Turn off bed, extruder, and fan
    M140 S0
    M104 S0
    M106 S0
    # Move nozzle away from print while retracting
    G91
    G1 E-3
    # Raise nozzle by 10mm
    G1 Z10 F3000
    G90
    G1 X245 Y245 Z230 F7000
    G1 E-1 F100
    #G1 X-2 Y-2 E-3 F300
    # Disable steppers
    M84

[gcode_macro TEST_MOTION]
gcode:
    {% set speed = "F30000" %}
    G28
    G0 Z100

    G0 X0 Y245 {speed}
    G0 X245 Y245 F{speed}
    G0 X245 Y0 F{speed}
    G0 X0 Y0 F{speed}
    G0 X245 Y245 F{speed}
    G0 X245 Y0 F{speed}
    G0 X0 Y245 F{speed}

    G0 X0 Y0 F{speed}
    G0 X245 Y0 F{speed}
    G0 X245 Y245 F{speed}
    G0 X0 Y245 F{speed}
    G0 X245 Y0 F{speed}
    G0 X0 Y245 F{speed}
    G0 X0 Y0 F{speed}
    G0 X245 Y245 F{speed}

    G0 X0 Y0 F{speed}

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 52.683
#*# pid_ki = 2.007
#*# pid_kd = 345.734
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 34.128
#*# pid_ki = 3.204
#*# pid_kd = 90.868
#*#
#*# [bed_mesh default_100]
#*# version = 1
#*# points =
#*# 	-0.130451, 0.089549, 0.099549, 0.104549, 0.109549, 0.109549, 0.109549, 0.089549, 0.079549, 0.054549
#*# 	0.059549, 0.079549, 0.099549, 0.114549, 0.124549, 0.134549, 0.139549, 0.129549, 0.129549, 0.119549
#*# 	0.004549, 0.054549, 0.084549, 0.099549, 0.114549, 0.124549, 0.134549, 0.139549, 0.139549, 0.139549
#*# 	-0.030451, 0.014549, 0.059549, 0.089549, 0.114549, 0.134549, 0.149549, 0.159549, 0.164549, 0.164549
#*# 	-0.060451, -0.030451, 0.024549, 0.069549, 0.099549, 0.119549, 0.144549, 0.149549, 0.164549, 0.174549
#*# 	-0.100451, -0.055451, -0.010451, 0.039549, 0.089549, 0.119549, 0.149549, 0.159549, 0.184549, 0.199549
#*# 	-0.160451, -0.100451, -0.055451, -0.000451, 0.054549, 0.099549, 0.134549, 0.149549, 0.174549, 0.189549
#*# 	-0.220451, -0.155451, -0.090451, -0.030451, 0.019549, 0.059549, 0.119549, 0.149549, 0.174549, 0.204549
#*# 	-0.280451, -0.205451, -0.150451, -0.085451, -0.015451, 0.024549, 0.084549, 0.129549, 0.144549, 0.179549
#*# 	-0.255451, -0.255451, -0.175451, -0.120451, -0.030451, 0.004549, 0.059549, 0.124549, 0.159549, 0.204549
#*# x_count = 10
#*# y_count = 10
#*# mesh_x_pps = 4
#*# mesh_y_pps = 4
#*# algo = bicubic
#*# tension = 0.5
#*# min_x = 35.0
#*# max_x = 219.95
#*# min_y = 35.0
#*# max_y = 209.96
#*#
#*# [bed_mesh default_25]
#*# version = 1
#*# points =
#*# 	  0.132001, 0.142001, 0.062001, -0.017999, -0.157999
#*# 	  0.107001, 0.132001, 0.117001, 0.062001, 0.022001
#*# 	  0.052001, 0.122001, 0.127001, 0.132001, 0.042001
#*# 	  0.002001, 0.117001, 0.127001, 0.172001, 0.232001
#*# 	  -0.097999, 0.047001, 0.147001, 0.212001, 0.247001
#*# min_x = 25.0
#*# max_x = 220.0
#*# min_y = 25.0
#*# max_y = 210.0
#*# x_count = 5
#*# y_count = 5
#*# mesh_x_pps = 4
#*# mesh_y_pps = 4
#*# algo = bicubic
#*# tension = 0.5
#*#
#*# [skew_correction skew_profile_1]
#*# xy_skew = 0.014205811504963698
#*# xz_skew = 0.0
#*# yz_skew = 0.0