linelog

# -*- text -*-
#
#  $Id$

#
#  The "linelog" module will log one line of text to a file.
#  Both the filename and the line of text are dynamically expanded.
#
#  We STRONGLY suggest that you do not use data from the
#  packet as part of the filename.
#
linelog {
	#
	#  The file where the logs will go.
	#
	#  If the filename is "syslog", then the log messages will
	#  go to syslog.
	filename = ${logdir}/linelog

	#
	#  The Unix-style permissions on the log file.
	#
	#  Depending on format string, the log file may contain secret or
	#  private information about users.  Keep the file permissions as
	#  restrictive as possible.
	permissions = 0600

	#
	# The Unix group of the log file.
	#
	# The user that freeradius runs as must be in the specified
	# group, otherwise it will not be possible to set the group.
	#
	# group = freerad

	#
	# If logging via syslog, the facility can be set here. Otherwise
	# the syslog_facility option in radiusd.conf will be used.
	#
	# syslog_facility = daemon

	#
	#  The default format string.
	format = "This is a log message for %{User-Name}"

	#
	#  This next line can be omitted.  If it is omitted, then
	#  the log message is static, and is always given by "format",
	#  above.
	#
	#  If it is defined, then the string is dynamically expanded,
	#  and the result is used to find another configuration entry
	#  here, with the given name.  That name is then used as the
	#  format string.
	#
	#  If the configuration entry cannot be found, then no log
	#  message is printed.
	#
	#  i.e. You can have many log messages in one "linelog" module.
	#  If this two-step expansion did not exist, you would have
	#  needed to configure one "linelog" module for each log message.

	#
	#  Reference the Packet-Type (Access-Request, etc.)  If it doesn't
	#  exist, reference the "format" entry, above.
	reference = "%{%{Packet-Type}:-format}"

	#
	#  Followed by a series of log messages.
	Access-Request = "Requested access: %{User-Name}"
	Access-Reject = "Rejected access: %{User-Name}"
	Access-Challenge = "Sent challenge: %{User-Name}"

	#
	#  The log messages can be grouped into sections and
        #  sub-sections, too.  The "reference" item needs to have a "."
	#  for every section.  e.g. reference = foo.bar will reference
	#  the "foo" section, "bar" configuration item.
	#

	#
	#  Used if:	reference = "foo.bar".
	foo {
	    bar = "Example log.  Please ignore"
	}

	#
	#  Another example:
	#      reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}"
	#
	Accounting-Request {
		Start = "Connect: [%{User-Name}] (did %{Called-Station-Id} cli %{Calling-Station-Id} port %{NAS-Port} ip %{Framed-IP-Address})"
		Stop = "Disconnect: [%{User-Name}] (did %{Called-Station-Id} cli %{Calling-Station-Id} port %{NAS-Port} ip %{Framed-IP-Address}) %{Acct-Session-Time} seconds"

		#  Don't log anything for these packets.
		Alive = ""

		Accounting-On = "NAS %C (%{NAS-IP-Address}) just came online"
		Accounting-Off = "NAS %C (%{NAS-IP-Address}) just went offline"

		# don't log anything for other Acct-Status-Types.
		unknown = ""
	}

}