/
print-mode.gcode
183 lines (179 loc) · 4.28 KB
/
print-mode.gcode
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
; ((((Anycubic Photon config file, compiled by Toby1kanobi))))
;(Delete all parameters)
;M8513
;Delete all parameters stored in inboard memory
;
;
;
;(Z stepper motor direction)
;M8004 I-1
; I1 Clockwise,
; I-1 Anticlockwise
;
;
;(XYZ Manual control movement direction)
;M8005 Z0
; 0: Z Normal
; 1: Z- Inverted
;
;
;(Speed/acceleration settings. Speed in mm/s, acceleration in mm/s^2)
;
;(Z axis default movement speed)
;M8006 I30
;
;
;(Jerk)
;M8007 I15
; Low value = high accuracy - significantly slower movement
; High value = Improved print times - Risk of losing steps
;
;
;(Acceleration)
M8008 I700
; The higher the acceleration the faster the overall print time. Too high risks losing steps.
;
;
;(Motion tuning)
;M8010 S0.000625
; Z per step of mm Formula: Lead/((360/1.8)*16)
; This setting allows you to replace the default leadscrew with other leadscrews that may have different thread pitches, a finer pitch will increase the machine's effective Z resolution. You must alter the Steps per mm acordingly
;
;
;(Max travel speed (Rapids)
;M8013 I20
; Z movement maximum speed mm/s
;
;
;(Zeroing speed)
;M8015 I3
; Initial homing speed
;
;
;(Zero varify)
;M8016 I2
; Second homing movement (Bounce) Setting 0 will disable the secon homing operation.
;
;
;(Peel and lift speeds)
;M8015 T2
; Initial peel speed slow move
;
;M8016 T3
; Build plate raise and lower speeds between layers
;
;
;(Z-axis Hold)
;M8016 D10
; The unit is ms (milliseconds) Time build plate will spend stationiary between rise and lower operations
;
;
;
;(Max Z height mm)
;M8026 I155
; Max Z height, this is th max Z move, not the max build height
; Changing this value can allow you to shorten or lengthen the max Z volume. You may use this to install a longer Z axis
;
;
;
;(Z axis limit switch position type)
;M8029 I0
; 0: Unilateral limit, only use Z-limit, do not use Z+
; 2: Double limit, if Z+ and Z- limit are used at the same time, Z+ can limit the maximum stroke of Z
;
;
;(Limit switch configuration)
;M8029 T0
; 0: Limit switch normally open (Active low)
; 1: Limit switch is normally closed (Active high)
;
;
;(Z axis limit switch position)
;M8029 S0
; 0: Limit switch is positioned for mix Z
; 1: Limit switch is positioned for Min Z
;
;
;(Z axis park position (0,0,0)
;M8029 C0
; 0 :ØZ Return to cordinate 0,0,0
; 1 :Stay in the limit position
;
;
;(LED fan LED_Fan control)
;M8030 I-2
; 0: Deactivated
; -1: Always on
; -2: Active when printing
;
;
;(Motherboard cooling fan MB_Fan control)
;M8030 T-2
; 0: Always off
; 1: On while LED is being oeprated
; -1: Always on
; -2: On when printing
;
;
;(LED light control)
;M8030 S4
; 4: On when image being displayed
;
;
;(U-disc)
;M8034 I1
; 0: Dissabled
; 1: Enabled
;
;
;(Peel lift distance FAST MOVE in mm - speed set by M8016)
M8070 Z6
; 0=Dissable
;
;
;(Peel first move SLOW MOVE, distance in mm - speed set by M8015)
M8070 S3
; 0=Dissable
;
;
;(Z zero and limit position setting)
;M8083 I1
; 0: Machine zero and limit switch position are the same
; 1: Machine zero and limit switch position are offset - set with M8084 Z*
;
;
;(Z limit and zero limit difference, the value is usually positive)
;M8084 Z0
; If you want to set the offset in the configuration, please remove the semicolon in front of the line command. You can also configure the offset automatically by setting°Z Zero¡± on the interface.
;
;
;(Boot LOGO time)
;M8085 I5000
; Boot logo duration, minimum 5000ms, maximum 6000ms
;
;
;(Screen saver - time to activation in seconds)
;M8085 T0
; 0=Dissabled
;
;
;(External drive settings)
;M8087 I0 T0
; I: Direction signal is valid to the establishment time of pulse signal high level, the unit is ns
; T: The minimum holding time of the pulse signal in ns. If there is no external drive control board, set both to zero.
; Several external drive parameters:THB7128:I100000 T0 ;;;;TB6560:I40000 T0 ;;;TB6600:I100000 T0
;
;
;
;(Action after printing)
;M8489 P3
; 0 = Dissable motors
; 1 = No function
; 2 = Home build plate, dissable motors (DO NOT USE)
; 3 = Move to max Z, dissable motors
;
;
;
;Save parameters)
M8500
; Save the configuration