forked from msproul/Arduino-stk500v2-bootloader
/
stk500boot.c
2135 lines (1845 loc) · 52.6 KB
/
stk500boot.c
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
/*****************************************************************************
Title: STK500v2 compatible bootloader
Modified for Wiring board ATMega128-16MHz
Author: Peter Fleury <pfleury@gmx.ch> http://jump.to/fleury
File: $Id: stk500boot.c,v 1.11 2006/06/25 12:39:17 peter Exp $
Compiler: avr-gcc 3.4.5 or 4.1 / avr-libc 1.4.3
Hardware: All AVRs with bootloader support, tested with ATmega8
License: GNU General Public License
Modified: Worapoht Kornkaewwattanakul <dev@avride.com> http://www.avride.com
Date: 17 October 2007
Update: 1st, 29 Dec 2007 : Enable CMD_SPI_MULTI but ignore unused command by return 0x00 byte response..
Compiler: WINAVR20060421
Description: add timeout feature like previous Wiring bootloader
DESCRIPTION:
This program allows an AVR with bootloader capabilities to
read/write its own Flash/EEprom. To enter Programming mode
an input pin is checked. If this pin is pulled low, programming mode
is entered. If not, normal execution is done from $0000
"reset" vector in Application area.
Size fits into a 1024 word bootloader section
when compiled with avr-gcc 4.1
(direct replace on Wiring Board without fuse setting changed)
USAGE:
- Set AVR MCU type and clock-frequency (F_CPU) in the Makefile.
- Set baud rate below (AVRISP only works with 115200 bps)
- compile/link the bootloader with the supplied Makefile
- program the "Boot Flash section size" (BOOTSZ fuses),
for boot-size 1024 words: program BOOTSZ01
- enable the BOOT Reset Vector (program BOOTRST)
- Upload the hex file to the AVR using any ISP programmer
- Program Boot Lock Mode 3 (program BootLock 11 and BootLock 12 lock bits) // (leave them)
- Reset your AVR while keeping PROG_PIN pulled low // (for enter bootloader by switch)
- Start AVRISP Programmer (AVRStudio/Tools/Program AVR)
- AVRISP will detect the bootloader
- Program your application FLASH file and optional EEPROM file using AVRISP
Note:
Erasing the device without flashing, through AVRISP GUI button "Erase Device"
is not implemented, due to AVRStudio limitations.
Flash is always erased before programming.
AVRdude:
Please uncomment #define REMOVE_CMD_SPI_MULTI when using AVRdude.
Comment #define REMOVE_PROGRAM_LOCK_BIT_SUPPORT to reduce code size
Read Fuse Bits and Read/Write Lock Bits is not supported
NOTES:
Based on Atmel Application Note AVR109 - Self-programming
Based on Atmel Application Note AVR068 - STK500v2 Protocol
LICENSE:
Copyright (C) 2006 Peter Fleury
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
*****************************************************************************/
//************************************************************************
//* Edit History
//************************************************************************
//* Jul 7, 2010 <MLS> = Mark Sproul msproul@skycharoit.com
//* Jul 7, 2010 <MLS> Working on mega2560. No Auto-restart
//* Jul 7, 2010 <MLS> Switched to 8K bytes (4K words) so that we have room for the monitor
//* Jul 8, 2010 <MLS> Found older version of source that had auto restart, put that code back in
//* Jul 8, 2010 <MLS> Adding monitor code
//* Jul 11, 2010 <MLS> Added blinking LED while waiting for download to start
//* Jul 11, 2010 <MLS> Added EEPROM test
//* Jul 29, 2010 <MLS> Added recchar_timeout for timing out on bootloading
//* Aug 23, 2010 <MLS> Added support for atmega2561
//* Aug 26, 2010 <MLS> Removed support for BOOT_BY_SWITCH
//* Sep 8, 2010 <MLS> Added support for atmega16
//* Nov 9, 2010 <MLS> Issue 392:Fixed bug that 3 !!! in code would cause it to jump to monitor
//* Jun 24, 2011 <MLS> Removed analogRead (was not used)
//* Dec 29, 2011 <MLS> Issue 181: added watch dog timmer support
//* Dec 29, 2011 <MLS> Issue 505: bootloader is comparing the seqNum to 1 or the current sequence
//* Jan 1, 2012 <MLS> Issue 543: CMD_CHIP_ERASE_ISP now returns STATUS_CMD_FAILED instead of STATUS_CMD_OK
//* Jan 1, 2012 <MLS> Issue 543: Write EEPROM now does something (NOT TESTED)
//* Jan 1, 2012 <MLS> Issue 544: stk500v2 bootloader doesn't support reading fuses
//************************************************************************
//************************************************************************
//* these are used to test issues
//* http://code.google.com/p/arduino/issues/detail?id=505
//* Reported by mark.stubbs, Mar 14, 2011
//* The STK500V2 bootloader is comparing the seqNum to 1 or the current sequence
//* (IE: Requiring the sequence to be 1 or match seqNum before continuing).
//* The correct behavior is for the STK500V2 to accept the PC's sequence number, and echo it back for the reply message.
#define _FIX_ISSUE_505_
//************************************************************************
//* Issue 181: added watch dog timmer support
#define _FIX_ISSUE_181_
#include <inttypes.h>
#include <avr/io.h>
#include <avr/interrupt.h>
#include <avr/boot.h>
#include <avr/pgmspace.h>
#include <util/delay.h>
#include <avr/eeprom.h>
#include <avr/common.h>
#include <stdlib.h>
#include "command.h"
#if defined(_MEGA_BOARD_) || defined(_BOARD_AMBER128_) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) \
|| defined(__AVR_ATmega2561__) || defined(__AVR_ATmega1284P__) || defined(ENABLE_MONITOR)
#undef ENABLE_MONITOR
#define ENABLE_MONITOR
static void RunMonitor(void);
#endif
#ifndef EEWE
#define EEWE 1
#endif
#ifndef EEMWE
#define EEMWE 2
#endif
//#define _DEBUG_SERIAL_
//#define _DEBUG_WITH_LEDS_
/*
* Uncomment the following lines to save code space
*/
//#define REMOVE_PROGRAM_LOCK_BIT_SUPPORT // disable program lock bits
//#define REMOVE_BOOTLOADER_LED // no LED to show active bootloader
//#define REMOVE_CMD_SPI_MULTI // disable processing of SPI_MULTI commands, Remark this line for AVRDUDE <Worapoht>
//
//************************************************************************
//* LED on pin "PROGLED_PIN" on port "PROGLED_PORT"
//* indicates that bootloader is active
//* PG2 -> LED on Wiring board
//************************************************************************
#define BLINK_LED_WHILE_WAITING
#ifdef _MEGA_BOARD_
#define PROGLED_PORT PORTB
#define PROGLED_DDR DDRB
#define PROGLED_PIN PINB7
#elif defined( _BOARD_AMBER128_ )
//* this is for the amber 128 http://www.soc-robotics.com/
//* onbarod led is PORTE4
#define PROGLED_PORT PORTD
#define PROGLED_DDR DDRD
#define PROGLED_PIN PINE7
#elif defined( _CEREBOTPLUS_BOARD_ ) || defined(_CEREBOT_II_BOARD_)
//* this is for the Cerebot 2560 board and the Cerebot-ii
//* onbarod leds are on PORTE4-7
#define PROGLED_PORT PORTE
#define PROGLED_DDR DDRE
#define PROGLED_PIN PINE7
#elif defined( _PENGUINO_ )
//* this is for the Penguino
//* onbarod led is PORTE4
#define PROGLED_PORT PORTC
#define PROGLED_DDR DDRC
#define PROGLED_PIN PINC6
#elif defined( _ANDROID_2561_ ) || defined( __AVR_ATmega2561__ )
//* this is for the Boston Android 2561
//* onbarod led is PORTE4
#define PROGLED_PORT PORTA
#define PROGLED_DDR DDRA
#define PROGLED_PIN PINA3
#elif defined( _BOARD_MEGA16 )
//* onbarod led is PORTA7
#define PROGLED_PORT PORTA
#define PROGLED_DDR DDRA
#define PROGLED_PIN PINA7
#define UART_BAUDRATE_DOUBLE_SPEED 0
#elif defined( _BOARD_BAHBOT_ )
//* dosent have an onboard LED but this is what will probably be added to this port
#define PROGLED_PORT PORTB
#define PROGLED_DDR DDRB
#define PROGLED_PIN PINB0
#elif defined( _BOARD_ROBOTX_ )
#define PROGLED_PORT PORTB
#define PROGLED_DDR DDRB
#define PROGLED_PIN PINB6
#elif defined( _BOARD_CUSTOM1284_BLINK_B0_ )
#define PROGLED_PORT PORTB
#define PROGLED_DDR DDRB
#define PROGLED_PIN PINB0
#elif defined( _BOARD_CUSTOM1284_ )
#define PROGLED_PORT PORTD
#define PROGLED_DDR DDRD
#define PROGLED_PIN PIND5
#elif defined( _AVRLIP_ )
#define PROGLED_PORT PORTB
#define PROGLED_DDR DDRB
#define PROGLED_PIN PINB5
#elif defined( _BOARD_STK500_ )
#define PROGLED_PORT PORTA
#define PROGLED_DDR DDRA
#define PROGLED_PIN PINA7
#elif defined( _BOARD_STK502_ )
#define PROGLED_PORT PORTB
#define PROGLED_DDR DDRB
#define PROGLED_PIN PINB5
#elif defined( _BOARD_STK525_ )
#define PROGLED_PORT PORTB
#define PROGLED_DDR DDRB
#define PROGLED_PIN PINB7
#else
#define PROGLED_PORT PORTG
#define PROGLED_DDR DDRG
#define PROGLED_PIN PING2
#endif
/*
* define CPU frequency in Mhz here if not defined in Makefile
*/
#ifndef F_CPU
#define F_CPU 16000000UL
#endif
#define _BLINK_LOOP_COUNT_ (F_CPU / 2250)
/*
* UART Baudrate, AVRStudio AVRISP only accepts 115200 bps
*/
#ifndef BAUDRATE
#define BAUDRATE 115200
#endif
/*
* Enable (1) or disable (0) USART double speed operation
*/
#ifndef UART_BAUDRATE_DOUBLE_SPEED
#if defined (__AVR_ATmega32__)
#define UART_BAUDRATE_DOUBLE_SPEED 0
#else
#define UART_BAUDRATE_DOUBLE_SPEED 1
#endif
#endif
/*
* HW and SW version, reported to AVRISP, must match version of AVRStudio
*/
#define CONFIG_PARAM_BUILD_NUMBER_LOW 0
#define CONFIG_PARAM_BUILD_NUMBER_HIGH 0
#define CONFIG_PARAM_HW_VER 0x0F
#define CONFIG_PARAM_SW_MAJOR 2
#define CONFIG_PARAM_SW_MINOR 0x0A
/*
* Calculate the address where the bootloader starts from FLASHEND and BOOTSIZE
* (adjust BOOTSIZE below and BOOTLOADER_ADDRESS in Makefile if you want to change the size of the bootloader)
*/
//#define BOOTSIZE 1024
#if FLASHEND > 0x0F000
#define BOOTSIZE 8192
#else
#define BOOTSIZE 2048
#endif
#define APP_END (FLASHEND -(2*BOOTSIZE) + 1)
/*
* Signature bytes are not available in avr-gcc io_xxx.h
*/
#if defined (__AVR_ATmega8__)
#define SIGNATURE_BYTES 0x1E9307
#elif defined (__AVR_ATmega16__)
#define SIGNATURE_BYTES 0x1E9403
#elif defined (__AVR_ATmega32__)
#define SIGNATURE_BYTES 0x1E9502
#elif defined (__AVR_ATmega8515__)
#define SIGNATURE_BYTES 0x1E9306
#elif defined (__AVR_ATmega8535__)
#define SIGNATURE_BYTES 0x1E9308
#elif defined (__AVR_ATmega162__)
#define SIGNATURE_BYTES 0x1E9404
#elif defined (__AVR_ATmega128__)
#define SIGNATURE_BYTES 0x1E9702
#elif defined (__AVR_ATmega1280__)
#define SIGNATURE_BYTES 0x1E9703
#elif defined (__AVR_ATmega2560__)
#define SIGNATURE_BYTES 0x1E9801
#elif defined (__AVR_ATmega2561__)
#define SIGNATURE_BYTES 0x1e9802
#elif defined (__AVR_ATmega1284P__)
#define SIGNATURE_BYTES 0x1e9705
#elif defined (__AVR_ATmega640__)
#define SIGNATURE_BYTES 0x1e9608
#elif defined (__AVR_ATmega64__)
#define SIGNATURE_BYTES 0x1E9602
#elif defined (__AVR_ATmega169__)
#define SIGNATURE_BYTES 0x1e9405
#elif defined (__AVR_AT90USB1287__)
#define SIGNATURE_BYTES 0x1e9782
#else
#error "no signature definition for MCU available"
#endif
#if defined(_BOARD_ROBOTX_) || defined(__AVR_AT90USB1287__) || defined(__AVR_AT90USB1286__)
#define UART_BAUD_RATE_LOW UBRR1L
#define UART_STATUS_REG UCSR1A
#define UART_CONTROL_REG UCSR1B
#define UART_ENABLE_TRANSMITTER TXEN1
#define UART_ENABLE_RECEIVER RXEN1
#define UART_TRANSMIT_COMPLETE TXC1
#define UART_RECEIVE_COMPLETE RXC1
#define UART_DATA_REG UDR1
#define UART_DOUBLE_SPEED U2X1
#elif defined(__AVR_ATmega8__) || defined(__AVR_ATmega16__) || defined(__AVR_ATmega32__) \
|| defined(__AVR_ATmega8515__) || defined(__AVR_ATmega8535__)
/* ATMega8 with one USART */
#define UART_BAUD_RATE_LOW UBRRL
#define UART_STATUS_REG UCSRA
#define UART_CONTROL_REG UCSRB
#define UART_ENABLE_TRANSMITTER TXEN
#define UART_ENABLE_RECEIVER RXEN
#define UART_TRANSMIT_COMPLETE TXC
#define UART_RECEIVE_COMPLETE RXC
#define UART_DATA_REG UDR
#define UART_DOUBLE_SPEED U2X
#elif defined(__AVR_ATmega64__) || defined(__AVR_ATmega128__) || defined(__AVR_ATmega162__) \
|| defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) || defined(__AVR_ATmega2561__)
/* ATMega with two USART, use UART0 */
#define UART_BAUD_RATE_LOW UBRR0L
#define UART_STATUS_REG UCSR0A
#define UART_CONTROL_REG UCSR0B
#define UART_ENABLE_TRANSMITTER TXEN0
#define UART_ENABLE_RECEIVER RXEN0
#define UART_TRANSMIT_COMPLETE TXC0
#define UART_RECEIVE_COMPLETE RXC0
#define UART_DATA_REG UDR0
#define UART_DOUBLE_SPEED U2X0
#elif defined(UBRR0L) && defined(UCSR0A) && defined(TXEN0)
/* ATMega with two USART, use UART0 */
#define UART_BAUD_RATE_LOW UBRR0L
#define UART_STATUS_REG UCSR0A
#define UART_CONTROL_REG UCSR0B
#define UART_ENABLE_TRANSMITTER TXEN0
#define UART_ENABLE_RECEIVER RXEN0
#define UART_TRANSMIT_COMPLETE TXC0
#define UART_RECEIVE_COMPLETE RXC0
#define UART_DATA_REG UDR0
#define UART_DOUBLE_SPEED U2X0
#elif defined(UBRRL) && defined(UCSRA) && defined(UCSRB) && defined(TXEN) && defined(RXEN)
//* catch all
#define UART_BAUD_RATE_LOW UBRRL
#define UART_STATUS_REG UCSRA
#define UART_CONTROL_REG UCSRB
#define UART_ENABLE_TRANSMITTER TXEN
#define UART_ENABLE_RECEIVER RXEN
#define UART_TRANSMIT_COMPLETE TXC
#define UART_RECEIVE_COMPLETE RXC
#define UART_DATA_REG UDR
#define UART_DOUBLE_SPEED U2X
#else
#error "no UART definition for MCU available"
#endif
/*
* Macro to calculate UBBR from XTAL and baudrate
*/
#if defined(__AVR_ATmega32__) && UART_BAUDRATE_DOUBLE_SPEED
#define UART_BAUD_SELECT(baudRate,xtalCpu) ((xtalCpu / 4 / baudRate - 1) / 2)
#elif defined(__AVR_ATmega32__)
#define UART_BAUD_SELECT(baudRate,xtalCpu) ((xtalCpu / 8 / baudRate - 1) / 2)
#elif UART_BAUDRATE_DOUBLE_SPEED
#define UART_BAUD_SELECT(baudRate,xtalCpu) (((float)(xtalCpu))/(((float)(baudRate))*8.0)-1.0+0.5)
#else
#define UART_BAUD_SELECT(baudRate,xtalCpu) (((float)(xtalCpu))/(((float)(baudRate))*16.0)-1.0+0.5)
#endif
/*
* States used in the receive state machine
*/
#define ST_START 0
#define ST_GET_SEQ_NUM 1
#define ST_MSG_SIZE_1 2
#define ST_MSG_SIZE_2 3
#define ST_GET_TOKEN 4
#define ST_GET_DATA 5
#define ST_GET_CHECK 6
#define ST_PROCESS 7
/*
* use 16bit address variable for ATmegas with <= 64K flash
*/
#if defined(RAMPZ)
typedef uint32_t address_t;
#else
typedef uint16_t address_t;
#endif
/*
* function prototypes
*/
static void sendchar(char c);
static unsigned char recchar(void);
/*
* since this bootloader is not linked against the avr-gcc crt1 functions,
* to reduce the code size, we need to provide our own initialization
*/
void __jumpMain (void) __attribute__ ((naked)) __attribute__ ((section (".init9")));
#include <avr/sfr_defs.h>
//#define SPH_REG 0x3E
//#define SPL_REG 0x3D
//*****************************************************************************
void __jumpMain(void)
{
//* July 17, 2010 <MLS> Added stack pointer initialzation
//* the first line did not do the job on the ATmega128
asm volatile ( ".set __stack, %0" :: "i" (RAMEND) );
//* set stack pointer to top of RAM
asm volatile ( "ldi 16, %0" :: "i" (RAMEND >> 8) );
asm volatile ( "out %0,16" :: "i" (AVR_STACK_POINTER_HI_ADDR) );
asm volatile ( "ldi 16, %0" :: "i" (RAMEND & 0x0ff) );
asm volatile ( "out %0,16" :: "i" (AVR_STACK_POINTER_LO_ADDR) );
asm volatile ( "clr __zero_reg__" ); // GCC depends on register r1 set to 0
asm volatile ( "out %0, __zero_reg__" :: "I" (_SFR_IO_ADDR(SREG)) ); // set SREG to 0
asm volatile ( "jmp main"); // jump to main()
}
//*****************************************************************************
void delay_ms(unsigned int timedelay)
{
unsigned int i;
for (i=0;i<timedelay;i++)
{
_delay_ms(0.5);
}
}
//*****************************************************************************
/*
* send single byte to USART, wait until transmission is completed
*/
static void sendchar(char c)
{
UART_DATA_REG = c; // prepare transmission
while (!(UART_STATUS_REG & (1 << UART_TRANSMIT_COMPLETE))); // wait until byte sent
UART_STATUS_REG |= (1 << UART_TRANSMIT_COMPLETE); // delete TXCflag
}
//************************************************************************
static int Serial_Available(void)
{
return(UART_STATUS_REG & (1 << UART_RECEIVE_COMPLETE)); // wait for data
}
//*****************************************************************************
/*
* Read single byte from USART, block if no data available
*/
static unsigned char recchar(void)
{
while (!(UART_STATUS_REG & (1 << UART_RECEIVE_COMPLETE)))
{
// wait for data
}
return UART_DATA_REG;
}
#define MAX_TIME_COUNT (F_CPU >> 1)
//*****************************************************************************
static unsigned char recchar_timeout(void)
{
uint32_t count = 0;
while (!(UART_STATUS_REG & (1 << UART_RECEIVE_COMPLETE)))
{
// wait for data
count++;
if (count > MAX_TIME_COUNT)
{
unsigned int data;
#if (FLASHEND > 0x10000)
data = pgm_read_word_far(0); //* get the first word of the user program
#else
data = pgm_read_word_near(0); //* get the first word of the user program
#endif
if (data != 0xffff) //* make sure its valid before jumping to it.
{
asm volatile(
"clr r30 \n\t"
"clr r31 \n\t"
"ijmp \n\t"
);
}
count = 0;
}
}
return UART_DATA_REG;
}
//* for watch dog timer startup
void (*app_start)(void) = 0x0000;
//*****************************************************************************
int main(void)
{
address_t address = 0;
address_t eraseAddress = 0;
unsigned char msgParseState;
unsigned int ii = 0;
unsigned char checksum = 0;
unsigned char seqNum = 0;
unsigned int msgLength = 0;
unsigned char msgBuffer[285];
unsigned char c, *p;
unsigned char isLeave = 0;
unsigned long boot_timeout;
unsigned long boot_timer;
unsigned int boot_state;
#ifdef ENABLE_MONITOR
unsigned int exPointCntr = 0;
unsigned int rcvdCharCntr = 0;
#endif
//* some chips dont set the stack properly
asm volatile ( ".set __stack, %0" :: "i" (RAMEND) );
asm volatile ( "ldi 16, %0" :: "i" (RAMEND >> 8) );
asm volatile ( "out %0,16" :: "i" (AVR_STACK_POINTER_HI_ADDR) );
asm volatile ( "ldi 16, %0" :: "i" (RAMEND & 0x0ff) );
asm volatile ( "out %0,16" :: "i" (AVR_STACK_POINTER_LO_ADDR) );
#ifdef _FIX_ISSUE_181_
//************************************************************************
//* Dec 29, 2011 <MLS> Issue #181, added watch dog timmer support
//* handle the watch dog timer
uint8_t mcuStatusReg;
mcuStatusReg = MCUSR;
__asm__ __volatile__ ("cli");
__asm__ __volatile__ ("wdr");
MCUSR = 0;
WDTCSR |= _BV(WDCE) | _BV(WDE);
WDTCSR = 0;
__asm__ __volatile__ ("sei");
// check if WDT generated the reset, if so, go straight to app
if (mcuStatusReg & _BV(WDRF))
{
app_start();
}
//************************************************************************
#endif
boot_timer = 0;
boot_state = 0;
#ifdef BLINK_LED_WHILE_WAITING
// boot_timeout = 90000; //* should be about 4 seconds
// boot_timeout = 170000;
boot_timeout = 20000; //* should be about 1 second
#else
boot_timeout = 3500000; // 7 seconds , approx 2us per step when optimize "s"
#endif
/*
* Branch to bootloader or application code ?
*/
#ifndef REMOVE_BOOTLOADER_LED
/* PROG_PIN pulled low, indicate with LED that bootloader is active */
PROGLED_DDR |= (1<<PROGLED_PIN);
// PROGLED_PORT &= ~(1<<PROGLED_PIN); // active low LED ON
PROGLED_PORT |= (1<<PROGLED_PIN); // active high LED ON
#ifdef _DEBUG_WITH_LEDS_
for (ii=0; ii<3; ii++)
{
PROGLED_PORT &= ~(1<<PROGLED_PIN); // turn LED off
delay_ms(100);
PROGLED_PORT |= (1<<PROGLED_PIN); // turn LED on
delay_ms(100);
}
#endif
#endif
/*
* Init UART
* set baudrate and enable USART receiver and transmiter without interrupts
*/
#if UART_BAUDRATE_DOUBLE_SPEED
UART_STATUS_REG |= (1 <<UART_DOUBLE_SPEED);
#endif
UART_BAUD_RATE_LOW = UART_BAUD_SELECT(BAUDRATE,F_CPU);
UART_CONTROL_REG = (1 << UART_ENABLE_RECEIVER) | (1 << UART_ENABLE_TRANSMITTER);
asm volatile ("nop"); // wait until port has changed
#ifdef _DEBUG_SERIAL_
// delay_ms(500);
sendchar('s');
sendchar('t');
sendchar('k');
// sendchar('5');
// sendchar('0');
// sendchar('0');
sendchar('v');
sendchar('2');
sendchar(0x0d);
sendchar(0x0a);
delay_ms(100);
#endif
while (boot_state==0)
{
while ((!(Serial_Available())) && (boot_state == 0)) // wait for data
{
_delay_ms(0.001);
boot_timer++;
if (boot_timer > boot_timeout)
{
boot_state = 1; // (after ++ -> boot_state=2 bootloader timeout, jump to main 0x00000 )
}
#ifdef BLINK_LED_WHILE_WAITING
if ((boot_timer % _BLINK_LOOP_COUNT_) == 0)
{
//* toggle the LED
PROGLED_PORT ^= (1<<PROGLED_PIN); // turn LED ON
}
#endif
}
boot_state++; // ( if boot_state=1 bootloader received byte from UART, enter bootloader mode)
}
if (boot_state==1)
{
//* main loop
while (!isLeave)
{
/*
* Collect received bytes to a complete message
*/
msgParseState = ST_START;
while ( msgParseState != ST_PROCESS )
{
if (boot_state==1)
{
boot_state = 0;
c = UART_DATA_REG;
}
else
{
// c = recchar();
c = recchar_timeout();
}
#ifdef ENABLE_MONITOR
rcvdCharCntr++;
if ((c == '!') && (rcvdCharCntr < 10))
{
exPointCntr++;
if (exPointCntr == 3)
{
RunMonitor();
exPointCntr = 0; // reset back to zero so we dont get in an endless loop
isLeave = 1;
msgParseState = 99; //* we dont want it do anything
break;
}
}
else
{
exPointCntr = 0;
}
#endif
switch (msgParseState)
{
case ST_START:
if ( c == MESSAGE_START )
{
msgParseState = ST_GET_SEQ_NUM;
checksum = MESSAGE_START^0;
}
break;
case ST_GET_SEQ_NUM:
#ifdef _FIX_ISSUE_505_
seqNum = c;
msgParseState = ST_MSG_SIZE_1;
checksum ^= c;
#else
if ( (c == 1) || (c == seqNum) )
{
seqNum = c;
msgParseState = ST_MSG_SIZE_1;
checksum ^= c;
}
else
{
msgParseState = ST_START;
}
#endif
break;
case ST_MSG_SIZE_1:
msgLength = c<<8;
msgParseState = ST_MSG_SIZE_2;
checksum ^= c;
break;
case ST_MSG_SIZE_2:
msgLength |= c;
msgParseState = ST_GET_TOKEN;
checksum ^= c;
break;
case ST_GET_TOKEN:
if ( c == TOKEN )
{
msgParseState = ST_GET_DATA;
checksum ^= c;
ii = 0;
}
else
{
msgParseState = ST_START;
}
break;
case ST_GET_DATA:
msgBuffer[ii++] = c;
checksum ^= c;
if (ii == msgLength )
{
msgParseState = ST_GET_CHECK;
}
break;
case ST_GET_CHECK:
if ( c == checksum )
{
msgParseState = ST_PROCESS;
}
else
{
msgParseState = ST_START;
}
break;
} // switch
} // while(msgParseState)
/*
* Now process the STK500 commands, see Atmel Appnote AVR068
*/
switch (msgBuffer[0])
{
#ifndef REMOVE_CMD_SPI_MULTI
case CMD_SPI_MULTI:
{
unsigned char answerByte;
unsigned char flag=0;
if ( msgBuffer[4]== 0x30 )
{
unsigned char signatureIndex = msgBuffer[6];
if ( signatureIndex == 0 )
{
answerByte = (SIGNATURE_BYTES >> 16) & 0x000000FF;
}
else if ( signatureIndex == 1 )
{
answerByte = (SIGNATURE_BYTES >> 8) & 0x000000FF;
}
else
{
answerByte = SIGNATURE_BYTES & 0x000000FF;
}
}
else if ( msgBuffer[4] & 0x50 )
{
//* Issue 544: stk500v2 bootloader doesn't support reading fuses
//* I cant find the docs that say what these are supposed to be but this was figured out by trial and error
// answerByte = boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS);
// answerByte = boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS);
// answerByte = boot_lock_fuse_bits_get(GET_EXTENDED_FUSE_BITS);
if (msgBuffer[4] == 0x50)
{
answerByte = boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS);
}
else if (msgBuffer[4] == 0x58)
{
answerByte = boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS);
}
else
{
answerByte = 0;
}
}
else
{
answerByte = 0; // for all others command are not implemented, return dummy value for AVRDUDE happy <Worapoht>
}
if ( !flag )
{
msgLength = 7;
msgBuffer[1] = STATUS_CMD_OK;
msgBuffer[2] = 0;
msgBuffer[3] = msgBuffer[4];
msgBuffer[4] = 0;
msgBuffer[5] = answerByte;
msgBuffer[6] = STATUS_CMD_OK;
}
}
break;
#endif
case CMD_SIGN_ON:
msgLength = 11;
msgBuffer[1] = STATUS_CMD_OK;
msgBuffer[2] = 8;
msgBuffer[3] = 'A';
msgBuffer[4] = 'V';
msgBuffer[5] = 'R';
msgBuffer[6] = 'I';
msgBuffer[7] = 'S';
msgBuffer[8] = 'P';
msgBuffer[9] = '_';
msgBuffer[10] = '2';
break;
case CMD_GET_PARAMETER:
{
unsigned char value;
switch(msgBuffer[1])
{
case PARAM_BUILD_NUMBER_LOW:
value = CONFIG_PARAM_BUILD_NUMBER_LOW;
break;
case PARAM_BUILD_NUMBER_HIGH:
value = CONFIG_PARAM_BUILD_NUMBER_HIGH;
break;
case PARAM_HW_VER:
value = CONFIG_PARAM_HW_VER;
break;
case PARAM_SW_MAJOR:
value = CONFIG_PARAM_SW_MAJOR;
break;
case PARAM_SW_MINOR:
value = CONFIG_PARAM_SW_MINOR;
break;
default:
value = 0;
break;
}
msgLength = 3;
msgBuffer[1] = STATUS_CMD_OK;
msgBuffer[2] = value;
}
break;
case CMD_LEAVE_PROGMODE_ISP:
isLeave = 1;
//* fall thru
case CMD_SET_PARAMETER:
case CMD_ENTER_PROGMODE_ISP:
msgLength = 2;
msgBuffer[1] = STATUS_CMD_OK;
break;
case CMD_READ_SIGNATURE_ISP:
{
unsigned char signatureIndex = msgBuffer[4];
unsigned char signature;
if ( signatureIndex == 0 )
signature = (SIGNATURE_BYTES >>16) & 0x000000FF;
else if ( signatureIndex == 1 )
signature = (SIGNATURE_BYTES >> 8) & 0x000000FF;
else
signature = SIGNATURE_BYTES & 0x000000FF;
msgLength = 4;
msgBuffer[1] = STATUS_CMD_OK;
msgBuffer[2] = signature;
msgBuffer[3] = STATUS_CMD_OK;
}
break;
case CMD_READ_LOCK_ISP:
msgLength = 4;
msgBuffer[1] = STATUS_CMD_OK;
msgBuffer[2] = boot_lock_fuse_bits_get( GET_LOCK_BITS );
msgBuffer[3] = STATUS_CMD_OK;
break;
case CMD_READ_FUSE_ISP:
{
unsigned char fuseBits;
if ( msgBuffer[2] == 0x50 )
{
if ( msgBuffer[3] == 0x08 )
fuseBits = boot_lock_fuse_bits_get( GET_EXTENDED_FUSE_BITS );
else
fuseBits = boot_lock_fuse_bits_get( GET_LOW_FUSE_BITS );
}
else
{
fuseBits = boot_lock_fuse_bits_get( GET_HIGH_FUSE_BITS );
}
msgLength = 4;
msgBuffer[1] = STATUS_CMD_OK;
msgBuffer[2] = fuseBits;
msgBuffer[3] = STATUS_CMD_OK;
}
break;
#ifndef REMOVE_PROGRAM_LOCK_BIT_SUPPORT
case CMD_PROGRAM_LOCK_ISP:
{
unsigned char lockBits = msgBuffer[4];
lockBits = (~lockBits) & 0x3C; // mask BLBxx bits
boot_lock_bits_set(lockBits); // and program it
boot_spm_busy_wait();
msgLength = 3;
msgBuffer[1] = STATUS_CMD_OK;
msgBuffer[2] = STATUS_CMD_OK;
}
break;
#endif
case CMD_CHIP_ERASE_ISP:
eraseAddress = 0;
msgLength = 2;
// msgBuffer[1] = STATUS_CMD_OK;
msgBuffer[1] = STATUS_CMD_FAILED; //* isue 543, return FAILED instead of OK
break;
case CMD_LOAD_ADDRESS:
#if defined(RAMPZ)
address = ( ((address_t)(msgBuffer[1])<<24)|((address_t)(msgBuffer[2])<<16)|((address_t)(msgBuffer[3])<<8)|(msgBuffer[4]) )<<1;
#else
address = ( ((msgBuffer[3])<<8)|(msgBuffer[4]) )<<1; //convert word to byte address
#endif
msgLength = 2;
msgBuffer[1] = STATUS_CMD_OK;
break;
case CMD_PROGRAM_FLASH_ISP:
case CMD_PROGRAM_EEPROM_ISP:
{
unsigned int size = ((msgBuffer[1])<<8) | msgBuffer[2];
unsigned char *p = msgBuffer+10;
unsigned int data;
unsigned char highByte, lowByte;
address_t tempaddress = address;
if ( msgBuffer[0] == CMD_PROGRAM_FLASH_ISP )
{
// erase only main section (bootloader protection)
if (eraseAddress < APP_END )
{
boot_page_erase(eraseAddress); // Perform page erase