Smart Meter Interface: EasyMeter Q3C

[btro1404]

There are two IR connectors at EasyMeter Q3C: One at the front and one on the top of the housing. The config below uses the top one:

>D

>B
;disable publishing at MQTT teleperiod, on boot
smlj=0
=>sensor53 r

>S
;re-enable publishing at MQTT teleperiod, after 10 seconds of uptime
if upsecs>10
then
smlj=1
endif

>M 1
+1,3,s,0,9600,Zaehler,1
1,77070101010800ff@1000,01.08.00 T0Bezug,kWh,Verbrauch1,7
1,77070102020800ff@1000,02.08.00 T0Liefer,kWh,Lieferung1,7
1,=h<hr/>
1,77070101010801ff@1000,01.08.01 T1Bezug,kWh,VerbrauchT1,2
1,77070101010802ff@1000,01.08.02 T2Bezug,kWh,VerbrauchT2,2
1,77070101010803ff@1000,01.08.03 T3Bezug,kWh,VerbrauchT3,2
1,77070101010804ff@1000,01.08.04 T4Bezug,kWh,VerbrauchT4,2
1,77070101010805ff@1000,01.08.05 T5Bezug,kWh,VerbrauchT5,2
1,77070101010806ff@1000,01.08.06 T6Bezug,kWh,VerbrauchT6,2
1,77070102020807ff@1000,02.08.07 T7Liefer,kWh,LieferungT7,2
1,77070102020808ff@1000,02.08.08 T8Liefer,kWh,LieferungT8,2
1,=h<hr/>
1,77070100010700ff@1,01.07.00 Pges,W,Pges,2
1,77070100150700ff@1,21.07.00 P_L1,W,P_L1,2
1,77070100290700ff@1,41.07.00 P_L2,W,P_L2,2
1,770701003d0700ff@1,61.07.00 P_L3,W,P_L3,2
1,=h<hr/>
#

[lied]

I have the same EasyMeter and I'm also using the top interface, the other one doesn't work for me... I receive data for usage, but not for power delivered back to the grid. Can you tell me if you config is showing anything else than 0 for "Lieferung" values?

[btro1404]

I'm sorry, but I have no access to the meter device anymore

[c7h]

EasyMeter Q3C here! More specifically an Q3CA1181.
I modified the above example and was able to read the delivered power. I still need to find out how to get obis codes 01.08.XX and all others connected to usage.

here is my config:

>D

>B
;disable publishing at MQTT teleperiod, on boot
smlj=0
=>sensor53 r

>S
;re-enable publishing at MQTT teleperiod, after 10 seconds of uptime
if upsecs>10
then
smlj=1
endif

>M 1
+1,3,s,0,9600,
; Einspeisung total:
1,77070100020700FF@1,02.07.00 P-,W,Power_minus,2
; Einspeisung L1-L3
1,77070100160700FF@1,22.07.00 P-L1,W,Power_minus_L1,2
1,770701002A0700FF@1,42.07.00 P-L2,W,Power_minus_L2,2
1,770701003E0700FF@1,62.07.00 P-L3,W,Power_minus_L3,2
1,=h<hr/>
;staus as hex.. ignore for now until we know what means what
1,77070100600505FF@1,status,hex,status,0
1,=h<hr/>
; Power back to the grid for tariff 1 - 8
1,77070101020801FF@1000,02.08.01 T1Liefer,kWh,LieferungT1,2
1,77070101020802FF@1000,02.08.02 T2Liefer,kWh,LieferungT2,2
1,77070101020803FF@1000,02.08.03 T3Liefer,kWh,LieferungT3,2
1,77070101020804FF@1000,02.08.04 T4Liefer,kWh,LieferungT4,2
1,77070101020805FF@1000,02.08.05 T5Liefer,kWh,LieferungT5,2
1,77070101020806FF@1000,02.08.06 T6Liefer,kWh,LieferungT6,2
1,77070101020807FF@1000,02.08.07 T7Liefer,kWh,LieferungT7,2
1,77070101020808FF@1000,02.08.08 T8Liefer,kWh,LieferungT8,2
1,=h<hr/>
#

@btro1404 did you unlock your meter with the pin?

[Noschvie]

Have you tried the debug mode and the Tasmota SML Dekoder?

[btro1404]

@btro1404 did you unlock your meter with the pin?

No, the Network Operator didn't set one