printer-20221009_134312.cfg

#Mainsail settings
[include mainsail.cfg]
[include macros.cfg]
[include timelapse.cfg]
#Other settings..
# This file contains pin mappings for the stock 2020 Creality Ender 3
# V2. To use this config, during "make menuconfig" select the
# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
# communication.

# If you prefer a direct serial connection, in "make menuconfig"
# select "Enable extra low-level configuration options" and select
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
# cable used for the LCD module as follows:
# 3: Tx, 4: Rx, 9: GND, 10: VCC

# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.

# See docs/Config_Reference.md for a description of parameters.

[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 39.55967
endstop_pin: ^PA5
position_endstop: 0
position_max: 230
homing_speed: 50

[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 39.89413
endstop_pin: ^PA6
position_endstop: -10
position_min: -10
position_max: 220
homing_speed: 50

[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
#endstop_pin: ^PA7
endstop_pin: probe:z_virtual_endstop
#position_endstop: 0.0
position_min: -3
position_max: 250

[extruder]
max_extrude_only_distance: 500
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
rotation_distance: 7.45
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
#control: pid
# tuned for stock hardware with 200 degree Celsius target
#pid_Kp: 21.527
#pid_Ki: 1.063
#pid_Kd: 108.982
min_temp: 0
max_temp: 300
pressure_advance: 0.0627

[heater_bed]
heater_pin: PA2
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
#control: pid
# tuned for stock hardware with 50 degree Celsius target
#pid_Kp: 54.027
#pid_Ki: 0.770
#pid_Kd: 948.182
min_temp: 0
max_temp: 130

[fan]
pin: PA0

[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command

[mcu host]
serial: /tmp/klipper_host_mcu

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100

[temperature_sensor raspberry_pi]
sensor_type: temperature_host
min_temp: 10
max_temp: 100

[temperature_sensor mcu_temp]
sensor_type: temperature_mcu
min_temp: 0
max_temp: 100

[input_shaper]
shaper_freq_x: 47.003
shaper_freq_y: 38.144
shaper_type: mzv

[bed_screws]
screw1: 56, 73
screw2: 56, 220
screw3: 224, 220
screw4: 224, 73

[bltouch]
sensor_pin: ^PB1
control_pin: PB0
x_offset: 35.5
y_offset: 1
#z_offset: 0

[safe_z_home]
home_xy_position: 75.5,107
speed: 50
z_hop: 10
z_hop_speed: 5

[screws_tilt_adjust]
screw1: 56, 73 
screw1_name: front left screw
screw2: 56, 220
screw2_name: rear left screw
screw3: 224, 220
screw3_name: rear right screw
screw4: 224, 73
screw4_name: front right screw
horizontal_move_z: 10.
speed: 50.
screw_thread: CW-M3

[bed_mesh]
speed: 120
horizontal_move_z: 5
mesh_min: 035.5, 1
mesh_max: 214, 215
probe_count: 6, 5
algorithm: bicubic
fade_start: 1
fade_end: 10
fade_target: 0

#[output_pin caselight]
#pin: host:gpio20

#[gcode_macro TOGGLE_CASELIGHT]
#gcode:
#	SET_PIN PIN=caselight VALUE={(not printer['output_pin caselight'].value)|int}

#[fan]
#pin: host:gpio20

# [stepper_z]
# position_endstop = 0.370

[firmware_retraction]
retract_length: 0.8
#   The length of filament (in mm) to retract when G10 is activated,
#   and to unretract when G11 is activated (but see
#   unretract_extra_length below). The default is 0 mm.
retract_speed: 50
#   The speed of retraction, in mm/s. The default is 20 mm/s.
unretract_extra_length: 0
#   The length (in mm) of *additional* filament to add when
#   unretracting.
unretract_speed: 40
#   The speed of unretraction, in mm/s. The default is 10 mm/s.

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 19.011
#*# pid_ki = 0.968
#*# pid_kd = 93.393
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 65.060
#*# pid_ki = 1.451
#*# pid_kd = 729.483
#*#
#*# [bltouch]
#*# z_offset = 5.205
#*#
#*# [bed_mesh Back]
#*# version = 1
#*# points =
#*# 	-0.020000, 0.022500, -0.002500, 0.027500, 0.025000, 0.070000
#*# 	-0.010000, 0.030000, -0.010000, 0.032500, 0.037500, 0.090000
#*# 	-0.000000, 0.025000, -0.002500, 0.032500, 0.040000, 0.102500
#*# 	0.017500, 0.037500, -0.012500, 0.017500, 0.025000, 0.075000
#*# 	0.037500, 0.052500, 0.015000, 0.045000, 0.052500, 0.115000
#*# x_count = 6
#*# y_count = 5
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 19.5
#*# max_x = 200.5
#*# min_y = 37.0
#*# max_y = 180.0