Raspberry Pi based remote for the Sportdog SD-400 shock collar in Go. It uses rpitx to transmit RF directly to the GPIO. You only need a Raspberry Pi, no other equipment needed.
This software uses rpitx to transmit RF signals directly from the Raspberry Pi's GPIO pins. Before you transmit, know your laws. You are responsible for using this software legally.
This software is really janky. I would strongly discourage you from using this for your production shock collar service. rpitx has also been reported to cause file system corruption in the past, so I would recommend backing up your Raspberry Pi before you attempt to use this software.
This project is not associated with Sportdog.
Plug a wire on GPIO 4 (Pin 7) on the GPIO header. This will serve as the antenna.
Then on your Raspberry Pi:
git clone https://github.com/F5OEO/rpitx.git
cd rpitx
# This is the version of rpitx I've tested with. Newer versions may or may not work.
git checkout 1423af8c6eb201a92d992965e01073717cbc5fdb
./install.sh
go get github.com/biribiribiri/shockcollar
cd $GOPATH/src/github.com/biribiribiri/shockcollar
go get ./...
cd $GOPATH/src/github.com/biribiribiri/shockcollar/remote
# Start the server. Collar commands can be sent via the CLI, gRPC, or via HTTP.
# Needs to be run as root because rpitx needs to be run as root.
# Probably not super secure...
sudo ./remote --rpitx=$PATH_TO_RPITX
After starting the remote, you need to pair your collar:
- Turn the collar off.
- Press and hold the collar power button until the collar LED turns off (4-5 seconds)
- Send the "continuous stimulation" (shock 1 8s) or "beep" (beep 8s) command from the remote until the collar LED blinks 5 times.
A simple web interface will start running on port 8000. You can use this to send commands to the collar.
The Sportdog Fieldtrainer 400 (SD-400) is a shock collar with momentary stimulation, continuous stimulation, and tone capabilities. The collar model number is FR-200, and the remote model number is FT-100.
This documentation should apply to any Sportdog training collar compatible with the FT-100 remote (including SD-400, SD-400S and SD-400CAMO).
The SD-400 remote uses binary FSK (frequency-shift keying) to send commands to the collar.
The carrier frequency is 27.255 MHz (Citizens Band Channel 23).
This document uses the following symbol definitions: '0': 0 Hz (unmodulated), 4 ms duration '1': 5 kHz modulation, 4 ms duration '2': 5 kHz modulation, 2 ms duration
The 2ms '2' symbol only appears to demarcate the end of a portion of a continuous command. All data symbols are either '0' or '1'.
There are two classes of commands sent by the remote:
- Momentary: Used for the momentary stimulation (nick) function.
- Continuous: Used for continuous stimulation and tone function.
"Momentary" commands sent by the remote are 43-bits long (172 ms).
Format:
1 1111 0001 [16-bit remote ID] [8-bit command type] [8-bit command arg] 10
"Continuous" commands have a similar structure to the momentary commands, but the transmission sequence repeats for as long as the button is held.
Start:
1 1111 0001 [16-bit remote ID] [8-bit command type] [8-bit command arg] 102
Repeated N times:
0001 [16-bit remote ID] [8-bit command type] [8-bit command arg] 102
End:
0001 [16-bit remote ID] [8-bit command type] [8-bit command arg] 1021111111111
For both momentary and continuous commands, if the remote is in "standby-mode" (no buttons pressed for some time), then the initial sequence of 5 '1's (20ms), becomes 23.5 bits long instead (94ms). However, the collar doesn't seem to require this.
The FT-100 has an 8-position dial, and 3 buttons (up, down, side). In the default Mode 1, these buttons have the following functions:
- Up: Continuous shock at the specified level for up to 8 seconds.
- Down: Nick at the specified level.
- Side: Beep.
At this time, only the Mode 1 commands have been documented. The other modes provide additional functionality, such as exposing 16 levels of continuous stimulation.
Example remote IDs: 0x6695, 0x999a
The remote is TX-only and the collar is RX-only. A remote has a fixed ID that it broadcasts. A collar will pair to a remote, and will only listen to its paired remote's ID. To pair a collar to a real or emulated remote:
- Turn the collar off.
- Press and hold the collar power button until the collar LED turns off (4-5 seconds)
- Send the "continuous stimulation" or "beep" command from the remote until the collar LED blinks 5 times.
- Arg: 0xa9
- Level 1: 0xa9
- Level 2: 0xa6
- Level 3: 0xa5
- Level 4: 0x9a
- Level 5: 0x99
- Level 6: 0x95
- Level 7: 0x6a
- Level 8: 0x55
The arguments are the same as the Nick command.
- Level 1: 0xa9
- Level 2: 0xa6
- Level 3: 0xa5
- Level 4: 0x9a
- Level 5: 0x99
- Level 6: 0x95
- Level 7: 0x6a
- Level 8: 0x55