This chapter will show you how to use C instead of assembly code as the programming language for the OS. Assembly is very good for interacting with the CPU and enables maximum control over every aspect of the code. However, at least for the authors, C is a much more convenient language to use. Therefore, we would like to use C as much as possible and use assembly code only where it make sense.
One prerequisite for using C is a stack, since all non-trivial C programs use
a stack. Setting up a stack is not harder than to make the esp register
point to the end of an area of free memory (remember that the stack grows
towards lower addresses on the x86) that is correctly aligned (alignment on 4 bytes is
recommended from a performance perspective).
We could point esp to a random area in memory since, so far, the only thing
in the memory is GRUB, BIOS, the OS kernel and some memory-mapped I/O. This is
not a good idea - we don't know how much memory is available or if the
area esp would point to is used by something else. A better idea is to
reserve a piece of uninitialized memory in the bss section in the ELF file
of the kernel. It is better to use the bss section instead of the
data section to reduce the size of the OS executable. Since GRUB understands
ELF, GRUB will allocate any memory reserved in the bss section
when loading the OS.
The NASM pseudo-instruction resb [@resb] can be used to declare uninitialized
data:
KERNEL_STACK_SIZE equ 4096 ; size of stack in bytes
section .bss
align 4 ; align at 4 bytes
kernel_stack: ; label points to beginning of memory
resb KERNEL_STACK_SIZE ; reserve stack for the kernel
There is no need to worry about the use of uninitialized memory for the stack, since it is not possible to read a stack location that has not been written (without manual pointer fiddling). A (correct) program can not pop an element from the stack without having pushed an element onto the stack first. Therefore, the memory locations of the stack will always be written to before they are being read.
The stack pointer is then set up by pointing esp to the end of the
kernel_stack memory:
mov esp, kernel_stack + KERNEL_STACK_SIZE ; point esp to the start of the
; stack (end of memory area)
The next step is to call a C function from assembly code. There are many
different conventions for how to call C code from assembly code
[@wiki:ccall]. This book uses the cdecl calling convention, since that is the
one used by GCC. The cdecl calling convention states that arguments to a
function should be passed via the stack (on x86). The arguments of the function
should be pushed on the stack in a right-to-left order, that is, you push the
rightmost argument first. The return value of the function is placed in the
eax register. The following code shows an example:
/* The C function */
int sum_of_three(int arg1, int arg2, int arg3)
{
return arg1 + arg2 + arg3;
}
; The assembly code
extern sum_of_three ; the function sum_of_three is defined elsewhere
push dword 3 ; arg3
push dword 2 ; arg2
push dword 1 ; arg1
call sum_of_three ; call the function, the result will be in eax
In the rest of this book, you will often come across "configuration bytes" that are a collection of bits in a very specific order. Below follows an example with 32 bits:
Bit: | 31 24 | 23 8 | 7 0 |
Content: | index | address | config |
Instead of using an unsigned integer, unsigned int, for handling such
configurations, it is much more convenient to use "packed structures":
struct example {
unsigned char config; /* bit 0 - 7 */
unsigned short address; /* bit 8 - 23 */
unsigned char index; /* bit 24 - 31 */
};
When using the struct in the previous example there is no guarantee that the
size of the struct will be exactly 32 bits - the compiler can add some
padding between elements for various reasons, for example to speed up element
access or due to requirements set by the hardware and/or compiler. When using a
struct to represent configuration bytes, it is very important that the
compiler does not add any padding, because the struct will eventually be
treated as a 32 bit unsigned integer by the hardware. The attribute packed
can be used to force GCC to not add any padding:
struct example {
unsigned char config; /* bit 0 - 7 */
unsigned short address; /* bit 8 - 23 */
unsigned char index; /* bit 24 - 31 */
} __attribute__((packed));
Note that __attribute__((packed)) is not part of the C standard - it might
not work with all C compilers.
When compiling the C code for the OS, a lot of flags to GCC need to be used. This is because the C code should not assume the presence of a standard library, since there is no standard library available for our OS. For more information about the flags, see the GCC manual.
The flags used for compiling the C code are:
-m32 -nostdlib -nostdinc -fno-builtin -fno-stack-protector -nostartfiles
-nodefaultlibs
As always when writing C programs we recommend turning on all warnings and treat warnings as errors:
-Wall -Wextra -Werror
You can now create a function kmain in a file called kmain.c that you call
from loader.s. At this point, kmain probably won't need any arguments (but
in later chapters it will).
Now is also probably a good time to set up some build tools to make it easier
to compile and test-run the OS. We recommend using make [@make], but there are
plenty of other build systems available. A simple Makefile for the OS could
look like the following example:
OBJECTS = loader.o kmain.o
CC = gcc
CFLAGS = -m32 -nostdlib -nostdinc -fno-builtin -fno-stack-protector \
-nostartfiles -nodefaultlibs -Wall -Wextra -Werror -c
LDFLAGS = -T link.ld -melf_i386
AS = nasm
ASFLAGS = -f elf
all: kernel.elf
kernel.elf: $(OBJECTS)
ld $(LDFLAGS) $(OBJECTS) -o kernel.elf
os.iso: kernel.elf
cp kernel.elf iso/boot/kernel.elf
genisoimage -R \
-b boot/grub/stage2_eltorito \
-no-emul-boot \
-boot-load-size 4 \
-A os \
-input-charset utf8 \
-quiet \
-boot-info-table \
-o os.iso \
iso
run: os.iso
bochs -f bochsrc.txt -q
%.o: %.c
$(CC) $(CFLAGS) $< -o $@
%.o: %.s
$(AS) $(ASFLAGS) $< -o $@
clean:
rm -rf *.o kernel.elf os.iso
The contents of your working directory should now look like the following figure:
.
|-- bochsrc.txt
|-- iso
| |-- boot
| |-- grub
| |-- menu.lst
| |-- stage2_eltorito
|-- kmain.c
|-- loader.s
|-- Makefile
You should now be able to start the OS with the simple command make run, which will compile the kernel and boot it up in Bochs (as defined in the
Makefile above).
- Kernigan & Richie's book, The C Programming Language, Second Edition, [@knr] is great for learning about all the aspects of C.