-
-
Notifications
You must be signed in to change notification settings - Fork 400
/
loraconf_sample.h
85 lines (70 loc) · 3.18 KB
/
loraconf_sample.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
#ifndef __LORACONF_H__
#define __LORACONF_H__
#if (HAS_LORA)
/************************************************************
* LMIC LoRaWAN configuration
*
* Read the values from TTN console (or whatever applies), insert them here,
* and rename this file to shared/loraconf.h
*
* You can configure OTAA or ABP Activation. In order to use ABP, uncomment
* (enable) the following line, but you should only do so, if you have good
* reasons for not using OTAA.
*
*************************************************************/
//#define LORA_ABP
#ifndef LORA_ABP
/************************************************************
* OTAA configuration
*
* DEVEUI, APPEUI and APPKEY should all be specified in MSB format as
* displayed in TTN console, so you can cut & paste from there. This is different
* from standard LMIC-Arduino which expects DEVEUI and APPEUI in LSB format.
* For TTN, APPEUI in MSB format always starts with 0x70, 0xB3, 0xD5.
* Set your DEVEUI here, if your device has have a fixed one.
* If you leave this untouched, then the DEVEUI will be derived from device's
* MAC adress during startup and will be displayed on device's screen as well as
* on serial console, if you set 'verbose 1' in paxcounter.conf and
* 'debug_level 3' in platformio.ini.
* If using a board with Microchip 24AA02E64 Uinique ID for deveui, the DEVEUI
* will be overwritten by the one contained in the Microchip module.
*
************************************************************/
static const u1_t DEVEUI[8] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00};
static const u1_t APPEUI[8] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00};
static const u1_t APPKEY[16] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00};
#endif
#ifdef LORA_ABP
/************************************************************
* ABP configuration (for development)
*
* Get your
* - Network Session Key (NWKSKEY)
* - App Session Key and your (APPSKEY)
* - Device Address (DEVADDR)
* from e.g. TTN console and replace the example values below.
*
* NOTE: Use MSB format (as displayed in TTN console, so you can cut & paste
* from there)
*
* NOTE: You may also need to adjust lorawan_abp.cpp in order to configure
* different channels and data rate channels to match your country's regulations
* and your network's settings.
*
************************************************************/
// ID of LoRaAlliance assigned Network (for a list, see e.g. here
// https://www.thethingsnetwork.org/docs/lorawan/prefix-assignments.html)
static const u1_t NETID = 0x13; // TTN
static const u1_t NWKSKEY[16] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00};
static const u1_t APPSKEY[16] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00};
static const u4_t DEVADDR =
0x00000000; // <-- Change this address for every node!
// set additional ABP parameters in loraconf_abp.cpp
void setABPParameters();
#endif
#endif // HAS_LORA
#endif // __LORACONF_H__