/
hw_MP2_v0.3.h
285 lines (235 loc) · 9.47 KB
/
hw_MP2_v0.3.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
/*
Copyright 2018 Benjamin Vedder benjamin@vedder.se
This file is part of the VESC firmware.
The VESC firmware is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published byNTC_RES
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
The VESC firmware is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
//Modified from "hw_100_250.h"
#ifndef HW_MP2_
#define HW_MP2_
//Preliminary conf file for ***V0.3*** MP2/F405 pill
#define HW_NAME "MP2"
// HW properties
#define HW_HAS_3_SHUNTS
#define INVERTED_SHUNT_POLARITY
#define HW_HAS_PHASE_FILTERS
#define HW_USE_BRK
// Macros
#define LED_GREEN_GPIO GPIOC
#define LED_GREEN_PIN 12
#define LED_RED_GPIO GPIOC
#define LED_RED_PIN 9
#define LED_GREEN_ON() palSetPad(LED_GREEN_GPIO, LED_GREEN_PIN)
#define LED_GREEN_OFF() palClearPad(LED_GREEN_GPIO, LED_GREEN_PIN)
#define LED_RED_ON() palSetPad(LED_RED_GPIO, LED_RED_PIN)
#define LED_RED_OFF() palClearPad(LED_RED_GPIO, LED_RED_PIN)
// Phase filter
#define PHASE_FILTER_OFF() palSetPad(GPIOC, 13); palSetPad(GPIOC, 14); palSetPad(GPIOC, 15)
#define PHASE_FILTER_ON() palClearPad(GPIOC, 13); palClearPad(GPIOC, 14); palClearPad(GPIOC, 15)
#define BRK_GPIO GPIOB
#define BRK_PIN 12
/*
* ADC Vector
*
* 0 (1): IN0 SENS1
* 1 (2): IN1 SENS2
* 2 (3): IN2 SENS3
* 3 (1): IN10 CURR1
* 4 (2): IN11 CURR2
* 5 (3): IN12 CURR3
* 6 (1): IN5 ADC_EXT1
* 7 (2): IN6 ADC_EXT2
* 8 (3): IN3 TEMP_MOS
* 9 (1): IN14 TEMP_MOTOR
* 10 (2): IN15 ADC_EXT3
* 11 (3): IN13 AN_IN
* 12 (1): Vrefint
* 13 (2): IN0 SENS1
* 14 (3): IN1 SENS2
* 15 (1): IN8 TEMP_MOS_2
* 16 (2): IN9 TEMP_MOS_3
* 17 (3): IN3 SENS3
*/
#define HW_ADC_CHANNELS 15 //?
#define HW_ADC_INJ_CHANNELS 3
#define HW_ADC_NBR_CONV 5
// ADC Indexes
#define ADC_IND_SENS1 3
#define ADC_IND_SENS2 4
#define ADC_IND_SENS3 5
#define ADC_IND_CURR1 0
#define ADC_IND_CURR2 1
#define ADC_IND_CURR3 2
#define ADC_IND_VIN_SENS 11
#define ADC_IND_EXT 6 //PA4
#define ADC_IND_EXT2 7 //PA7
#define ADC_IND_TEMP_MOS 10 //? FET temp is on PB1
#define ADC_IND_TEMP_MOTOR 7 //? PA7... also jumpered to A brake
#define ADC_IND_VREFINT 12
// ADC macros and settings
//****************************************************************************************************************************************************
// MP2 has a bug (feature?) where the phase voltage dividers are different from the bus voltage dividers.
// for this reason the VIN_R1 and VIN_R2 are different from the values used in the GET_INPUT_VOLTAGE macro
//****************************************************************************************************************************************************
// Component parameters (can be overridden)
#ifndef V_REG
#define V_REG 3.30
#endif
#ifndef VIN_R1
#define VIN_R1 100000.0
#endif
#ifndef VIN_R2
#define VIN_R2 3300.0 // single value for phase voltage dividers
#endif
#ifndef CURRENT_AMP_GAIN
#define CURRENT_AMP_GAIN 21.88
#endif
#ifndef CURRENT_SHUNT_RES
#define CURRENT_SHUNT_RES (0.0005 / 3.0) //3 0.5 mOhm shunts in parallel
#endif
// Input voltage
#ifndef VIN_BUS_R1
#define VIN_BUS_R1 270000.0
#endif
#ifndef VIN_BUS_R2
#define VIN_BUS_R2 11000.0 // default value, for 16s max batteries, all solder jumpers open.
//#define VIN_BUS_R2 8913.8 // for 20s max batteries, 100v solder jumper soldered.
//#define VIN_BUS_R2 5958.3 // for 30s max batteries, 150v solder jumper soldered.
#endif
#define GET_INPUT_VOLTAGE() ((V_REG / 4095.0) * (float)ADC_Value[ADC_IND_VIN_SENS] * ((VIN_BUS_R1 + VIN_BUS_R2) / VIN_BUS_R2))
// #define GET_INPUT_VOLTAGE() ((V_REG / 4095.0) * (float)ADC_Value[ADC_IND_VIN_SENS] * ((VIN_R1 + VIN_R2) / VIN_R2)) // default macro, not used for MP2 v0.3 because of separate values for phase and bus voltage dividers
// NTC Termistors
#define NTC_RES(adc_val) ((4095.0 * 10000.0) / (4095.0-adc_val) - 10000.0)
#define NTC_TEMP(adc_ind) hwMP2_get_temp()
#define NTC_RES_MOTOR(adc_val) (10000.0 / ((4095.0 / (float)adc_val) - 1.0)) // Motor temp sensor on low side
#define NTC_TEMP_MOTOR(beta) (1.0 / ((logf(NTC_RES_MOTOR(ADC_Value[ADC_IND_TEMP_MOTOR]) / 10000.0) / beta) + (1.0 / 298.15)) - 273.15)
#define NTC_TEMP_MOS1() (1.0 / ((logf(NTC_RES(ADC_Value[ADC_IND_TEMP_MOS]) / 10000.0) / 3380.0) + (1.0 / 298.15)) - 273.15)
#define NTC_TEMP_MOS2() (0.0)// (1.0 / ((logf(NTC_RES(ADC_Value[ADC_IND_TEMP_MOS_2]) / 10000.0) / 3380.0) + (1.0 / 298.15)) - 273.15)
#define NTC_TEMP_MOS3() (0.0)// (1.0 / ((logf(NTC_RES(ADC_Value[ADC_IND_TEMP_MOS_3]) / 10000.0) / 3380.0) + (1.0 / 298.15)) - 273.15)
// Voltage on ADC channel
#define ADC_VOLTS(ch) ((float)ADC_Value[ch] / 4096.0 * V_REG)
// COMM-port ADC GPIOs
//#define HW_ADC_EXT_GPIO GPIOA
//#define HW_ADC_EXT_PIN 5
//#define HW_ADC_EXT2_GPIO GPIOA
//#define HW_ADC_EXT2_PIN 6
// UART Peripheral
#define HW_UART_DEV SD3
#define HW_UART_GPIO_AF GPIO_AF_USART3
#define HW_UART_TX_PORT GPIOB
#define HW_UART_TX_PIN 10
#define HW_UART_RX_PORT GPIOB
#define HW_UART_RX_PIN 11
// ICU Peripheral for servo decoding
#define HW_USE_SERVO_TIM4
#define HW_ICU_TIMER TIM4
#define HW_ICU_TIM_CLK_EN() RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE)
#define HW_ICU_DEV ICUD4
#define HW_ICU_CHANNEL ICU_CHANNEL_1
#define HW_ICU_GPIO_AF GPIO_AF_TIM4
#define HW_ICU_GPIO GPIOB
#define HW_ICU_PIN 6
// I2C Peripheral
#define HW_I2C_DEV I2CD2
#define HW_I2C_GPIO_AF GPIO_AF_I2C2
#define HW_I2C_SCL_PORT GPIOB
#define HW_I2C_SCL_PIN 10
#define HW_I2C_SDA_PORT GPIOB
#define HW_I2C_SDA_PIN 11
// Hall/encoder pins
#define HW_HALL_ENC_GPIO1 GPIOC
#define HW_HALL_ENC_PIN1 6
#define HW_HALL_ENC_GPIO2 GPIOC
#define HW_HALL_ENC_PIN2 7
#define HW_HALL_ENC_GPIO3 GPIOC
#define HW_HALL_ENC_PIN3 8
#define HW_ENC_TIM TIM3
#define HW_ENC_TIM_AF GPIO_AF_TIM3
#define HW_ENC_TIM_CLK_EN() RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE)
#define HW_ENC_EXTI_PORTSRC EXTI_PortSourceGPIOC
#define HW_ENC_EXTI_PINSRC EXTI_PinSource8
#define HW_ENC_EXTI_CH EXTI9_5_IRQn
#define HW_ENC_EXTI_LINE EXTI_Line8
#define HW_ENC_EXTI_ISR_VEC EXTI9_5_IRQHandler
#define HW_ENC_TIM_ISR_CH TIM3_IRQn
#define HW_ENC_TIM_ISR_VEC TIM3_IRQHandler
// SPI pins
//#define HW_SPI_DEV SPID1
//#define HW_SPI_GPIO_AF GPIO_AF_SPI1
//#define HW_SPI_PORT_NSS GPIOA
//#define HW_SPI_PIN_NSS 4
//#define HW_SPI_PORT_SCK GPIOA
//#define HW_SPI_PIN_SCK 5 //Missing from F405 pill, TO BE UPDATED IN FUTURE F405 PILLs
//#define HW_SPI_PORT_MOSI GPIOA
//#define HW_SPI_PIN_MOSI 7
//#define HW_SPI_PORT_MISO GPIOA
//#define HW_SPI_PIN_MISO 6
// SPI pins
#define HW_SPI_DEV SPID1
#define HW_SPI_GPIO_AF GPIO_AF_SPI1
#define HW_SPI_PORT_NSS GPIOA
#define HW_SPI_PIN_NSS 4
#define HW_SPI_PORT_SCK GPIOA
#define HW_SPI_PIN_SCK 5
#define HW_SPI_PORT_MOSI GPIOA
#define HW_SPI_PIN_MOSI 7
#define HW_SPI_PORT_MISO GPIOA
#define HW_SPI_PIN_MISO 6
// Measurement macros
#define ADC_V_L1 ADC_Value[ADC_IND_SENS1]
#define ADC_V_L2 ADC_Value[ADC_IND_SENS2]
#define ADC_V_L3 ADC_Value[ADC_IND_SENS3]
#define ADC_V_ZERO (ADC_Value[ADC_IND_VIN_SENS] / 2)
// Macros
#define READ_HALL1() palReadPad(HW_HALL_ENC_GPIO1, HW_HALL_ENC_PIN1)
#define READ_HALL2() palReadPad(HW_HALL_ENC_GPIO2, HW_HALL_ENC_PIN2)
#define READ_HALL3() palReadPad(HW_HALL_ENC_GPIO3, HW_HALL_ENC_PIN3)
// Override dead time. See the stm32f4 reference manual for calculating this value.
#define HW_DEAD_TIME_NSEC 900.0
// Default setting overrides
#ifndef MCCONF_L_MIN_VOLTAGE
#define MCCONF_L_MIN_VOLTAGE 38.0 // Minimum input voltage due to DCDC brick cutout
#endif
#ifndef MCCONF_L_MAX_VOLTAGE
//#define MCCONF_L_MAX_VOLTAGE 90.0 // Maximum input voltage for 100v power stage / 20s max battery (100V power stage solder jumper soldered
//#define MCCONF_L_MAX_VOLTAGE 135.0 // Maximum input voltage for 150v power stage / 30s max battery (150v power stage solder jumper soldered))
#define MCCONF_L_MAX_VOLTAGE 73.0 // Maximum input voltage for 80v power stage / 16s max battery (no power stage solder jumper soldered))
#endif
#ifndef MCCONF_DEFAULT_MOTOR_TYPE
#define MCCONF_DEFAULT_MOTOR_TYPE MOTOR_TYPE_FOC
#endif
#ifndef MCCONF_FOC_F_ZV
#define MCCONF_FOC_F_ZV 30000.0
#endif
#ifndef MCCONF_L_MAX_ABS_CURRENT
#define MCCONF_L_MAX_ABS_CURRENT 320.0 // The maximum absolute current above which a fault is generated
#endif
#ifndef MCCONF_FOC_SAMPLE_V0_V7
#define MCCONF_FOC_SAMPLE_V0_V7 false // Run control loop in both v0 and v7 (requires phase shunts)
#endif
#ifndef MCCONF_L_IN_CURRENT_MAX
#define MCCONF_L_IN_CURRENT_MAX 150.0 // Input current limit in Amperes (Upper)
#endif
#ifndef MCCONF_L_IN_CURRENT_MIN
#define MCCONF_L_IN_CURRENT_MIN -150.0 // Input current limit in Amperes (Lower)
#endif
// Setting limits
#define HW_LIM_CURRENT -135.0, 135.0
#define HW_LIM_CURRENT_IN -135.0, 135.0
#define HW_LIM_CURRENT_ABS 0.0, 180.0
#define HW_LIM_VIN 36.0, 90.0
#define HW_LIM_ERPM -200e3, 200e3
#define HW_LIM_DUTY_MIN 0.0, 0.1
#define HW_LIM_DUTY_MAX 0.0, 0.99
#define HW_LIM_TEMP_FET -40.0, 95.0
// HW-specific functions
float hwMP2_get_temp(void);
#endif /* HW_MP2_ */