Configuration files for Lulzbot TAZ 6 using an Archim 2 board with a BTT PAD 7 for Klipper
Klipper Links
https://github.com/Klipper3d/klipper
https://github.com/Klipper3d/klipper/tree/master/docs
Mainsail documentation https://docs.mainsail.xyz/
Initial Setup and Configuration • Install Klipper on a device if needed ○ Installation - Klipper documentation (klipper3d.org) https://www.klipper3d.org/Installation.html • Install Moonraker ○ Installation - Moonraker https://moonraker.readthedocs.io/en/latest/installation/ • Install Klipperscreen for touchscreens ○ Installation - KlipperScreen https://klipperscreen.readthedocs.io/en/latest/Installation/#auto-install • Install Lulzbot version of Cura ○ https://www.lulzbot.com/cura • Verify printer bed is clean and empty • Turn on printer • Turn on device running Klipper • Verify amount of filament on spool • Verify thickness of filament for imperfections • Connect web browser to http://taz.local and verify connectivity • Open Cura and run through install steps for local printer • Install Moonraker plugin for Cura • Connect to Klipper • Set the theme settings ○ Lulzbot Lime Green § rgb(194, 215, 53) ○ Mainsail Quicktips | Themes https://youtu.be/kbSfLQtl4tA?si=HL7WomTxeTPDtKlo • Check E-Steps by running ??? command. • Use Orca calibration to check all of the settings ○ Calibration · SoftFever/OrcaSlicer Wiki (github.com) https://github.com/SoftFever/OrcaSlicer/wiki/Calibration
Cura Print Settings Build plate adhesion type, determine whether to print on raft, skirt, or brim Generate support or tree support Infill density Uncheck "keep heating" for build plate in Material section Change "Z Seam Alignment" to shortest or random for round prints
Initial Calibration Sites Teaching Tech 3D Printer Calibration (teachingtechyt.github.io) https://teachingtechyt.github.io/calibration.html Welcome! | Ellis’ Print Tuning Guide (ellis3dp.com) https://ellis3dp.com/Print-Tuning-Guide/
New Printer Setup Complete beginner's guide to 3D printing - Assembly, tour, slicing, levelling and first prints https://youtu.be/T-Z3GmM20JM
Verify Extruder E-Steps Run 100mm of filament through extruder to verify it is correct. Adjust as needed. Teaching Tech 3D Printer Calibration (teachingtechyt.github.io)
Set PID Autotune G-Codes - Klipper documentation (klipper3d.org) https://www.klipper3d.org/Config_checks.html?h=pid_calibrate#calibrate-pid-settings PID_CALIBRATE HEATER=<config_name> TARGET= [WRITE_FILE=1] PID_CALIBRATE HEATER=heater_bed TARGET=60 PID_CALIBRATE HEATER=extruder TARGET=205
SAVE_CONFIG
Set Z Offset Check Z-Offset Probe calibration - Klipper documentation (klipper3d.org) PROBE_CALIBRATE SAVE_CONFIG PROBE_ACCURACY
Resonance Compensation https://www.klipper3d.org/Resonance_Compensation.html
Pressure Advance https://www.klipper3d.org/Pressure_Advance.html
Bed Mesh Calibration https://www.klipper3d.org/G-Codes.html#bed_mesh_calibrate
Calibration Source Information https://teachingtechyt.github.io/calibration.html Retraction calibration code site - http://prahjister.duckdns.org