Buderus EM100 external flow temperature #1315

philipherbert · 2023-10-02T19:09:12Z

philipherbert
Oct 2, 2023

Hello,

is / should it be possible to set flow temperature for systems with external temperatur control, as it is possible with the em 100 module.
This module is used, when an external (non EMS) control needs to request a flow temperature. EM 100 is wired via 0-10V.

I would like to achive this with the EMS-ESP, instead of going through 0-10V output and into EM100.

Boiler Type GB192i.2

Thanks, Philip

MichaelDvP · 2023-10-03T13:12:02Z

MichaelDvP
Oct 3, 2023
Maintainer

Please go to help, download the support info and attach it here. We need to see the device-id and the telegrams from this device.

0 replies

philipherbert · 2023-10-16T15:31:59Z

philipherbert
Oct 16, 2023
Author

Today I have added the EM100 Module to the system,
it is recognized as PM10, but without any identities.
DIP/Function Switch is set to 3 for using the 0-10V Input as Control for supply temperature.

The following options are displayed on the BC400
Regulation Type (fixed by dip, niot changeable): SupplyTemperature
Input Value for OFF 0.0V
Input Value for MAX 10V
Max Temperature 90
Min Temperature 20

Diagnostic Page Shows:
T0: temperature low loss heater (according to to Documentation, no need to connect on an EMS+ Boiler, it can take the value from the sensor connected to the boiler)
IE0: Error Pump: Open
IO1; Inpurt 0..10V: Currently 0
OE1: LNG Valve OFF
OE1: Störungsanzeige OFF
IO1: Output Power: OFF
Solleistung Heizung: 0%
SupplySetPoint 0°

{
"System Info": {
"version": "3.6.3-dev.2",
"platform": "ESP32",
"uptime": "000+00:07:12.652",
"uptime (seconds)": 432,
"free mem": 109,
"max alloc": 43,
"free app": 6155,
"reset reason": "Software reset CPU / Software reset CPU"
},
"Network Info": {
"network": "WiFi",
"hostname": "ems-esp",
"RSSI": -36,
"IPv4 address": "192.168.121.227/255.255.255.240",
"IPv4 gateway": "192.168.121.238",
"IPv4 nameserver": "172.26.3.200",
"static ip config": false,
"enable IPv6": false,
"low bandwidth": true,
"disable sleep": true,
"enable MDNS": true,
"enable CORS": false,
"AP provision mode": "disconnected",
"AP security": "wpa2",
"AP ssid": "ems-esp"
},
"NTP Info": {
"NTP status": "connected",
"enabled": true,
"server": "time.google.com",
"tz label": "Europe/Berlin"
},
"OTA Info": {
"enabled": false,
"port": 8266
},
"MQTT Info": {
"MQTT status": "connected",
"MQTT publishes": 406,
"MQTT queued": 0,
"MQTT publish fails": 16,
"MQTT connects": 1,
"enabled": true,
"client id": "ems-esp",
"keep alive": 60,
"clean session": false,
"entity format": 1,
"base": "ems-esp",
"discovery prefix": "homeassistant",
"discovery type": 0,
"nested format": 2,
"ha enabled": true,
"mqtt qos": 0,
"mqtt retain": false,
"publish time heartbeat": 60,
"publish time boiler": 10,
"publish time thermostat": 10,
"publish time solar": 10,
"publish time mixer": 10,
"publish time other": 10,
"publish time sensor": 10,
"publish single": false,
"publish2command": false,
"send response": false
},
"Syslog Info": {
"enabled": true,
"syslog started": true,
"syslog level": "debug",
"syslog ip": "192.168.121.213",
"syslog queue": 1
},
"Sensor Info": {
"temperature sensors": 0,
"temperature sensor reads": 0,
"temperature sensor fails": 0,
"analog sensors": 0,
"analog sensor reads": 0,
"analog sensor fails": 0
},
"API Info": {
"API calls": 0,
"API fails": 0
},
"Bus Info": {
"bus status": "connected",
"bus protocol": "Buderus",
"bus telegrams received (rx)": 918,
"bus reads (tx)": 214,
"bus writes (tx)": 0,
"bus incomplete telegrams": 0,
"bus reads failed": 0,
"bus writes failed": 0,
"bus rx line quality": 100,
"bus tx line quality": 100
},
"Settings": {
"board profile": "S32",
"locale": "en",
"tx mode": 2,
"ems bus id": 11,
"shower timer": false,
"shower alert": false,
"hide led": false,
"notoken api": false,
"readonly mode": false,
"fahrenheit": false,
"dallas parasite": false,
"bool format": 4,
"bool dashboard": 1,
"enum format": 1,
"analog enabled": true,
"telnet enabled": true,
"max web log buffer": 50,
"web log buffer": 35
},
"Devices": [
{
"type": "boiler",
"name": "Condens 5000i/Greenstar 8000/GC9800IW/GB192i.2",
"device id": "0x08",
"product id": 195,
"version": "05.06",
"entities": 68,
"handlers received": "0xBF 0xC2 0x15 0xD1 0xE3 0xE4 0xE5 0xE9 0x04",
"handlers fetched": "0x14 0xE6 0xEA",
"handlers pending": "0x10 0x11 0x1C 0x18 0x19 0x1A 0x35 0x16 0x33 0x34 0x26 0x2A",
"handlers ignored": "0xD7 0xD8 0xF7 0x2E 0x3B"
},
{
"type": "thermostat",
"name": "UI800/BC400",
"device id": "0x10",
"product id": 4,
"version": "49.04",
"entities": 16,
"handlers received": "0x06 0x02B9 0x029B 0x02BA 0x02BB 0x02BC 0x031D 0x0267",
"handlers fetched": "0x0291 0x0292 0x0293 0x0294 0x02F5 0x023A 0x0240",
"handlers pending": "0xA3 0xA2 0x12 0x13 0x02A5 0x02AF 0x0471 0x02A6 0x02B0 0x029C 0x0472 0x02A7 0x02B1 0x029D 0x0473 0x02A8 0x02B2 0x029E 0x0474 0x02A9 0x02BD 0x02B3 0x029F 0x0475 0x02AA 0x02BE 0x02B4 0x02A0 0x0476 0x02AB 0x02BF 0x02B5 0x02A1 0x0477 0x02AC 0x02C0 0x02B6 0x02A2 0x0478 0x02CC 0x0467 0x02CE 0x0468 0x02D0",
"handlers ignored": "0xBF 0xE7 0xC4 0x07AB"
},
{
"type": "solar",
"name": "SM100/MS100",
"device id": "0x2A",
"product id": 163,
"version": "27.09",
"entities": 17,
"handlers received": "0x07D6 0x07AA",
"handlers fetched": "0x07A5 0x07A6 0x07AE 0x07E0",
"handlers pending": "0x07AB",
"handlers ignored": "0xF7 0x01 0x07A9 0x07AD 0x07B1 0xBF"
},
{
"type": "pump",
"name": "PM10",
"device id": "0x15",
"product id": 243,
"version": "04.06",
"entities": 0,
"handlers ignored": "0x01 0xF7 0x0939 0x093A 0xBF 0x0936 0x9C 0xD2 0xE2 0x0937 0x0938 0xF9"
}
]
}

0 replies

philipherbert · 2023-10-16T15:34:32Z

philipherbert
Oct 16, 2023
Author

ems-esp:$
000+00:17:33.104 N 2: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
000+00:17:33.285 N 3: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xD2), data: 00 00 (offset 1)
000+00:17:33.308 N 4: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xE2), data: 00
000+00:17:33.348 N 5: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0936), data: 00 00 00 00 00 00 (offset 1)
000+00:17:34.109 N 6: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0937), data: 80 00
000+00:17:34.295 N 7: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 01 00
000+00:17:35.091 N 8: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0939), data: 00 00 00 00
000+00:17:35.298 N 9: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 00 00 00 00 00 00 00 00 03 01
000+00:17:53.258 N 10: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
000+00:18:13.288 N 11: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
000+00:18:33.352 N 12: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
000+00:18:33.533 N 13: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xD2), data: 00 00 (offset 1)
000+00:18:33.557 N 14: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xE2), data: 00
000+00:18:33.596 N 15: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0936), data: 00 00 00 00 00 00 (offset 1)
000+00:18:34.357 N 16: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0937), data: 80 00
000+00:18:34.543 N 17: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 01 00
000+00:18:35.339 N 18: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0939), data: 00 00 00 00
000+00:18:35.545 N 19: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 00 00 00 00 00 00 00 00 03 01

1 reply

MichaelDvP Oct 18, 2023
Maintainer

Ok, let's check the values and telegrams:

it is recognized as PM10, but without any identities.

We have ID 0x15 since #720 as PM10, but this seems wrong, I'll change to EM10/EM100.

DIP/Function Switch is set to 3 for using the 0-10V Input as Control for supply temperature.

0x093A could be a config message, offset 9 as dip setting? Try a different setting to validate.

Diagnostic Page Shows:
T0: temperature low loss heater (according to to Documentation, no need to connect on an EMS+ Boiler, it can take the value from the sensor connected to the boiler)
IE0: Error Pump: Open
IO1; Inpurt 0..10V: Currently 0
OE1: LNG Valve OFF
OE1: Störungsanzeige OFF
IO1: Output Power: OFF
Solleistung Heizung: 0%
SupplySetPoint 0°

A lot of zeros, difficult to know which zero is what.
0xD2 is a 16bit command to the boiler, could be the analog input IO1
0xE2 is byte command to the boiler, one of the OFF commands?
Other telegrams are publishing states and measurements
0x937 is a temperature measurement with disconnected sensor (8000 means not connected for temperaturesensors), so thisis T0
For the other telegrams we need changing/different values to identify.

philipherbert · 2023-10-18T14:29:21Z

philipherbert
Oct 18, 2023
Author

Here is the output of 0x93a for different dip setting ...

changed 3
000+00:15:37.195 N 36: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 00 00 (offset 2)
000+00:15:38.203 N 37: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00
000+00:15:38.388 N 38: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 03 (offset 8)

changed 2
000+00:16:38.467 N 40: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 29 02 (offset 8)
000+00:16:39.547 N 41: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 01 01 29 (offset 2)
000+00:16:39.730 N 42: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 01

changed1
000+00:17:28.452 N 45: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 01
000+00:17:29.246 N 46: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 01 (offset 9)
000+00:17:29.608 N 47: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 01 (offset 2)

changed 4
000+00:18:15.620 N 49: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 00 00 (offset 2)
000+00:18:16.206 N 50: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00
000+00:18:16.812 N 51: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 04 (offset 8)

changed 5
000+00:19:00.905 N 52: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 00 00 00 00 00 00 00 00 05 01

0 replies

philipherbert · 2023-10-18T14:32:07Z

philipherbert
Oct 18, 2023
Author

here is the link to the documentation of the module
https://buderus-de-de.boschtt-documents.com/index/download/id/1228026

0 replies

philipherbert · 2023-10-20T18:48:58Z

philipherbert
Oct 20, 2023
Author

I have collected more data with dip setting 3, comments are between the ouput

set from 80 to 81 max (for 10V input)
001+22:50:53.142 N 123: [emsesp] thermostat(0x10) -R-> pump(0x15), ?(0xF9), length: 0x11
001+22:50:53.207 N 124: [emsesp] pump(0x15) -W-> thermostat(0x10), ?(0xF9), data: FF 08 35 03 0F 00 00 00 14 00 00 00 5A 00 00 00 5A 00 00 00 50
001+22:50:56.342 N 125: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 51 (offset 3)
001+22:50:56.871 N 126: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 51

set max to 80 (ffor 10 Input)

001+22:51:38.990 N 140: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 50 (offset 3)
001+22:51:39.283 N 141: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 50 (offset 3)
ems-esp:$

fset 5)

set min to 20 (for 0V Input)
001+22:52:03.344 N 144: [emsesp] thermostat(0x10) -R-> pump(0x15), ?(0xF9), length: 0x11
001+22:52:03.409 N 145: [emsesp] pump(0x15) -W-> thermostat(0x10), ?(0xF9), data: FF 08 35 04 0F 00 00 00 00 00 00 00 14 00 00 00 50 00 00 00 14
001+22:52:11.149 N 146: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 15 (offset 4)
001+22:52:11.442 N 147001+22:52:36.016 N 158: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 14 (offset 4)

set min go 21 (for 0 V Input)

001+22:52:36.511 N 159: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 14 (offset 4)
: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 15

set off value to 1 (off at 1V)

00 00 00 00 00 (offset 1)
001+22:53:23.602 N 168: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0937), data: 80 00
001+22:53:23.788 N 169: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 01 00
001+22:53:24.222 N 170: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0939), data: 00 00 00 00
001+22:53:24.430 N 171: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 00 00 00 00 00 00 00 00 03 01
001+22:53:28.550 N 172: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 0A (offset 1)
001+22:53:28.839 N 173: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 0A (offset 1)

set off value to 2 (off at 2V)
001+22:54:02.885 N 177: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
001+22:54:08.522 N 178: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 14 (offset 1)
001+22:54:08.991 N 179: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 14 (offset 1)

set off value to 0.5 (off at 0.5V)
001+22:54:42.933 N 190: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
001+22:54:43.881 N 191: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 05 (offset 1)
001+22:54:44.414 N 192: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 05 (offset 1)

set max go 9.7V (max 80 at 9,7V)
001+22:55:33.012 N 212: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 61 (offset 2)
001+22:55:33.489 N 213: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 61 (offset 2)

set max to 10V (max 80C at 10V)

001+22:55:58.422 N 217: [emsesp] thermostat(0x10) -W-> pump(0x15), ?(0x0935), data: 64 (offset 2)
001+22:55:58.495 N 218: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0935), data: 64 (offset 2)

DIP to 3
em100 settings:
OFF 0V
MAX 10V

Max Temp 80C
Min Temp 20C

set to 4,9V on EM100 Input before 0V
001+22:58:30.769 N 251: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 25 (offset 1)
001+22:58:32.695 N 252: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 31 (offset 1)
001+22:58:32.881 N 253: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0939), data: 64 2E
001+22:58:33.062 N 254: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xD2), data: 2E 64 (offset 1)
001+22:58:33.323 N 255: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xE2), data: 01
ems-esp:$

requestpower on diag page: 100% supplytemp on diag page: 46C (no need go heat up, boiler supply was > 46C )
001+22:58:30.769 N 251: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 25 (offset 1)
001+22:58:32.695 N 252: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 31 (offset 1)
001+22:58:32.881 N 253: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0939), data: 64 2E
001+22:58:33.062 N 254: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xD2), data: 2E 64 (offset 1)
001+22:58:33.323 N 255: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xE2), data: 01
001+22:58:43.243 N 256: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
001+22:59:03.289 N 257: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)

changed 9.8V to EM100 Input diag page requestpower current boiler current 13% seltemp 78Celsius 100%
001+22:59:36.664 N 266: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 3E (offset 1)
001+22:59:37.235 N 267: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 4A (offset 1)
001+22:59:37.420 N 268: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0939), data: 3E (offset 1)
001+22:59:37.839 N 269: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xD2), data: 3E (offset 1)
001+22:59:37.867 N 270: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 56 (offset 1)
001+22:59:38.229 N 271: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 62 (offset 1)
001+22:59:38.412 N 272: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0939), data: 4E (offset 1)
001+22:59:38.804 N 273: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xD2), data: 4E (offset 1)
001+22:59:43.265 N 274: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
001+22:59:51.547 N 275: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0936), data: 1F (offset 5)
001+23:00:01.337 N 276: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0936), data: 0D (offset 5)
001+23:00:03.304 N 277: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
001+23:00:23.304 N 278: [emsesp] pump(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
001+23:00:23.485 N 279: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xD2), data: 4E 64 (offset 1)
001+23:00:23.509 N 280: [emsesp] pump(0x15) -W-> boiler(0x08), ?(0xE2), data: 01
001+23:00:23.548 N 281: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0936), data: 00 00 00 00 0D 00 (offset 1)
001+23:00:23.949 N 282: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0937), data: 80 00
001+23:00:24.135 N 283: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0938), data: 01 62
001+23:00:24.562 N 284: [emsesp] pump(0x15) -B-> All(0x00), ?(0x0939), data: 64 4E 00 00
001+23:00:24.769 N 285: [emsesp] pump(0x15) -B-> All(0x00), ?(0x093A), data: 00 00 00 00 00 00 00 00 00 03 01

1 reply

MichaelDvP Oct 25, 2023
Maintainer

Please check with my testbuild if all values show up so far.

philipherbert · 2023-10-25T16:26:44Z

philipherbert
Oct 25, 2023
Author

uploaded four test firmware
EMS-ESP-3_6_3-dev_4e-ESP32_S3 via webui.

Device now offline. Did not reconnect after reboot. Am I doing something wrong ?
Last time I needed to reflash via USB .....

Currently I am not at the site, but could drive to the site, if I can provide some useful information.
The S3 Gateway was now up for 6 days and 20 hours.

wifi with dedicated AP, no mesh !

version": "3.6.3-dev.2",
"platform": "ESP32-S3",
"network": "WiFi",
"hostname": "ems-esp",
"RSSI": -45,
"IPv4 address": "192.168.121.229/255.255.255.240",
"IPv4 gateway": "192.168.121.238",
"IPv4 nameserver": "172.26.3.200",
"static ip config": false,
"enable IPv6": false,
"low bandwidth": false,
"disable sleep": true,
"enable MDNS": true,
"enable CORS": false,
"AP provision mode": "disconnected",
"AP security": "wpa2",
"AP ssid": "ems-esp"

0 replies

philipherbert · 2023-10-25T16:42:46Z

philipherbert
Oct 25, 2023
Author

device reconnected after a very long time (!) This never happened with the official builds.
I have not changed anything on the wifi side.

I will add syslog and screenshot from em100

Datum,Zeit,Stufe,Hostname,Kategorie,Programm,Nachrichten
2023-10-25,18:35:14,Info,192.168.121.229,kern,1,2023-10-25T18:35:14.656528+2:00 ems-esp emsesp - - - 000+00:16:30.050 I 651: Stopping Access Point
2023-10-25,18:35:13,Info,192.168.121.229,kern,1,2023-10-25T18:35:08.380587+2:00 ems-esp system - - - 000+00:16:23.515 I 650: NTP connected
2023-10-25,18:35:13,Info,192.168.121.229,daemon,1,2023-10-25T18:35:07.711376+2:00 ems-esp mqtt - - - 000+00:16:23.116 I 649: MQTT connected
2023-10-25,18:35:13,Info,192.168.121.229,kern,1,2023-10-25T18:35:07.662997+2:00 ems-esp emsesp - - - 000+00:16:23.045 I 648: mDNS responder service started
2023-10-25,18:35:13,Info,192.168.121.229,kern,1,"2023-10-25T18:35:07.637535+2:00 ems-esp emsesp - - - 000+00:16:23.038 I 647: WiFi connected with IP=192.168.121.229, hostname=ems-esp"
2023-10-25,18:35:12,Info,192.168.121.229,kern,1,2023-10-25T18:35:07.635437+2:00 ems-esp emsesp - - - 000+00:16:23.038 I 646: Starting NTP service
2023-10-25,18:35:12,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:20.050 W 645: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:12,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:20.050 I 644: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:12,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:17.044 W 643: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:12,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:17.044 I 642: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:12,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:14.038 W 641: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:12,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:14.038 I 640: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:12,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:11.031 W 639: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:12,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:11.031 I 638: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:12,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:08.024 W 637: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:11,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:08.024 I 636: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:11,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:05.017 W 635: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:11,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:05.017 I 634: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:11,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:02.010 W 633: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:11,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:02.010 I 632: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:11,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:59.004 W 631: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:11,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:59.004 I 630: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:11,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:55.997 W 629: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:11,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:55.997 I 628: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:11,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:52.991 W 627: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:10,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:52.991 I 626: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:10,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:49.985 W 625: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:10,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:49.985 I 624: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:10,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:46.979 W 623: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:10,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:46.979 I 622: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:10,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:43.971 W 621: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:10,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:43.971 I 620: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:10,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:40.964 W 619: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:10,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:40.964 I 618: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:10,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:37.958 W 617: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:09,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:37.958 I 616: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:09,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:34.951 W 615: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:09,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:34.951 I 614: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:09,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:31.940 W 613: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:09,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:31.940 I 612: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:09,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:28.933 W 611: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:09,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:28.933 I 610: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:09,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:25.923 W 609: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:09,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:25.923 I 608: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:09,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:22.917 W 607: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:08,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:22.917 I 606: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:08,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:19.910 W 605: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:08,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:19.910 I 604: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:08,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:16.903 W 603: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:08,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:16.903 I 602: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:07,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:13.896 W 601: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:07,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:15:13.896 I 600: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:07,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:15:10.890 W 599: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:18:44,Warnung,192.168.121.229,console,1,2023-10-25T18:18:43.712197+2:00 ems-esp telegram - - - 006+20:40:37.480 W 46303: Incomplete Rx: AA 00 2A 00 88 00 08
2023-10-25,18:18:43,Warnung,192.168.121.229,console,1,2023-10-25T18:18:43.666590+2:00 ems-esp telegram - - - 006+20:40:37.463 W 46302: Incomplete Rx: 10 00 95 00 15 00 88 00 08
2023-10-25,18:18:42,Warnung,192.168.121.229,console,1,2023-10-25T18:18:42.779390+2:00 ems-esp telegram - - - 006+20:40:36.572 W 46301: Incomplete Rx: 00 10 20 2D 2D 00 C8 3A 02 7E 64 0D 03 00 02 A0 00 00 02 60 00 7C 0D 00 02 9F 02 7E
2023-10-25,18:18:42,Warnung,192.168.121.229,console,1,2023-10-25T18:18:42.673785+2:00 ems-esp telegram - - - 006+20:40:36.456 W 46300: Incomplete Rx: 15 00 88 00 08
2023-10-25,18:18:42,Warnung,192.168.121.229,console,1,2023-10-25T18:18:42.357886+2:00 ems-esp telegram - - - 006+20:40:36.021 W 46299: Incomplete Rx: AA 00 2A 00 88 00 08 00 89 00 B1 00 88 00 08 00
2023-10-25,18:18:41,Warnung,192.168.121.229,console,1,2023-10-25T18:18:41.883316+2:00 ems-esp telegram - - - 006+20:40:35.667 W 46298: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:41,Warnung,192.168.121.229,console,1,2023-10-25T18:18:41.781942+2:00 ems-esp telegram - - - 006+20:40:35.459 W 46297: Incomplete Rx: 88 00 08 00 88 00 08 00 8B 00 91 00 90 00 10 00 88 00 08 00
2023-10-25,18:18:41,Warnung,192.168.121.229,console,1,2023-10-25T18:18:41.426942+2:00 ems-esp telegram - - - 006+20:40:35.207 W 46296: Incomplete Rx: 2A 00 88 00
2023-10-25,18:18:41,Warnung,192.168.121.229,console,1,2023-10-25T18:18:41.312244+2:00 ems-esp telegram - - - 006+20:40:35.096 W 46295: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:41,Warnung,192.168.121.229,console,1,2023-10-25T18:18:41.221863+2:00 ems-esp telegram - - - 006+20:40:34.881 W 46294: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:41,Warnung,192.168.121.229,console,1,2023-10-25T18:18:41.209658+2:00 ems-esp telegram - - - 006+20:40:34.881 W 46293: Incomplete Rx: 10 00 88 00 08 00 89 00 D8 00 95 00 15 00 88 00 08 00 AA 00 2A 00
2023-10-25,18:18:40,Warnung,192.168.121.229,console,1,2023-10-25T18:18:40.795567+2:00 ems-esp telegram - - - 006+20:40:34.579 W 46292: Incomplete Rx: 08 00 88 00 08
2023-10-25,18:18:40,Warnung,192.168.121.229,console,1,2023-10-25T18:18:40.642057+2:00 ems-esp telegram - - - 006+20:40:34.438 W 46291: Incomplete Rx: 08 00 97 00 88 00 08 00 88 00 08 00 89 00 98 00
2023-10-25,18:18:40,Warnung,192.168.121.229,console,1,2023-10-25T18:18:40.319655+2:00 ems-esp telegram - - - 006+20:40:34.100 W 46290: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:40,Warnung,192.168.121.229,console,1,2023-10-25T18:18:40.132352+2:00 ems-esp telegram - - - 006+20:40:33.909 W 46289: Incomplete Rx: 2A 00 88 00 08
2023-10-25,18:18:39,Warnung,192.168.121.229,console,1,2023-10-25T18:18:39.781095+2:00 ems-esp telegram - - - 006+20:40:33.565 W 46288: Incomplete Rx: 10 00 88 00
2023-10-25,18:18:39,Warnung,192.168.121.229,console,1,2023-10-25T18:18:39.703764+2:00 ems-esp telegram - - - 006+20:40:33.488 W 46287: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:39,Warnung,192.168.121.229,console,1,2023-10-25T18:18:39.229642+2:00 ems-esp telegram - - - 006+20:40:33.026 W 46286: Incomplete Rx: 90 00 10 00 88 00 08 00 89 00 A3 00 95 00 15 00 AA 00 2A 00 88 00 08 00
2023-10-25,18:18:39,Warnung,192.168.121.229,console,1,2023-10-25T18:18:39.055223+2:00 ems-esp telegram - - - 006+20:40:32.836 W 46285: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:39,Warnung,192.168.121.229,console,1,2023-10-25T18:18:38.984438+2:00 ems-esp telegram - - - 006+20:40:32.768 W 46284: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:38,Warnung,192.168.121.229,console,1,2023-10-25T18:18:38.726348+2:00 ems-esp telegram - - - 006+20:40:32.508 W 46283: Incomplete Rx: 15 00 88 00
2023-10-25,18:18:38,Warnung,192.168.121.229,console,1,2023-10-25T18:18:38.656639+2:00 ems-esp telegram - - - 006+20:40:32.329 W 46282: Incomplete Rx: 88 00 08 00 88 00 08 00 89 00 8F 00
2023-10-25,18:18:37,Warnung,192.168.121.229,console,1,2023-10-25T18:18:37.911980+2:00 ems-esp telegram - - - 006+20:40:31.694 W 46281: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:37,Warnung,192.168.121.229,console,1,2023-10-25T18:18:37.498522+2:00 ems-esp telegram - - - 006+20:40:31.164 W 46280: Incomplete Rx: 95 00 15 00 88 00 08 00 89 00 96 00 AA 00 2A 00 88 00 08 00 88 00 08 00
2023-10-25,18:18:37,Warnung,192.168.121.229,console,1,2023-10-25T18:18:37.362197+2:00 ems-esp telegram - - - 006+20:40:31.146 W 46279: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:37,Warnung,192.168.121.229,console,1,2023-10-25T18:18:37.272796+2:00 ems-esp telegram - - - 006+20:40:31.054 W 46278: Incomplete Rx: 88 00 08 00 88
2023-10-25,18:18:36,Warnung,192.168.121.229,console,1,2023-10-25T18:18:36.931361+2:00 ems-esp telegram - - - 006+20:40:30.605 W 46277: Incomplete Rx: 2A 00 88 00 08 00 88 00 08 00 8A 00 8B 00 88 00 08 00 89 00
2023-10-25,18:18:36,Warnung,192.168.121.229,console,1,2023-10-25T18:18:36.695890+2:00 ems-esp telegram - - - 006+20:40:30.476 W 46276: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:36,Warnung,192.168.121.229,console,1,2023-10-25T18:18:36.497940+2:00 ems-esp telegram - - - 006+20:40:30.282 W 46275: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:36,Warnung,192.168.121.229,console,1,2023-10-25T18:18:36.371701+2:00 ems-esp telegram - - - 006+20:40:30.041 W 46274: Incomplete Rx: B6 00 90 00 10 00 95 00 15 00 88 00 08 00 BE 00 AA 00 2A 00 88 00 08 00
2023-10-25,18:18:36,Warnung,192.168.121.229,console,1,2023-10-25T18:18:36.064438+2:00 ems-esp telegram - - - 006+20:40:29.847 W 46273: Incomplete Rx: 10 00 88 00 08
2023-10-25,18:18:36,Warnung,192.168.121.229,console,1,2023-10-25T18:18:35.980345+2:00 ems-esp telegram - - - 006+20:40:29.762 W 46272: Incomplete Rx: 08 00 88 00 08
2023-10-25,18:18:35,Warnung,192.168.121.229,console,1,2023-10-25T18:18:35.815094+2:00 ems-esp telegram - - - 006+20:40:29.484 W 46271: Incomplete Rx: 2A 00 88 00 08 00 89 00 92 00 88 00 08 00 8B 00 88 00 08 00
2023-10-25,18:18:33,Warnung,192.168.121.229,console,1,2023-10-25T18:18:33.356084+2:00 ems-esp telegram - - - 006+20:40:27.138 W 46270: Incomplete Rx: 88 00 08 00 D8
2023-10-25,18:18:32,Warnung,192.168.121.229,console,1,2023-10-25T18:18:32.422383+2:00 ems-esp telegram - - - 006+20:40:26.090 W 46269: Incomplete Rx: 90 00 10 00 88 00 08 00 B5 00 95 00 15 00 88 00 08 00 89 00
2023-10-25,18:18:31,Warnung,192.168.121.229,console,1,2023-10-25T18:18:31.857874+2:00 ems-esp telegram - - - 006+20:40:25.522 W 46268: Incomplete Rx: 90 00 10 00 88 00 08 00 95 00 15 00 94 00 AA 00 2A 00 88 00 08 00 89 00
2023-10-25,18:18:31,Warnung,192.168.121.229,console,1,2023-10-25T18:18:31.626730+2:00 ems-esp telegram - - - 006+20:40:25.408 W 46267: Incomplete Rx: 08 00 88 00 08
2023-10-25,18:18:31,Warnung,192.168.121.229,console,1,2023-10-25T18:18:31.293465+2:00 ems-esp telegram - - - 006+20:40:24.977 W 46266: Incomplete Rx: 88 00 08 00 88 00 08 00 8B 00 8A 00 90 00 10 00 88 00 08 00
2023-10-25,18:18:30,Warnung,192.168.121.229,console,1,2023-10-25T18:18:30.846911+2:00 ems-esp telegram - - - 006+20:40:24.631 W 46265: Incomplete Rx: 10 00 88 00 08
2023-10-25,18:18:30,Warnung,192.168.121.229,console,1,2023-10-25T18:18:30.763094+2:00 ems-esp telegram - - - 006+20:40:24.547 W 46264: Incomplete Rx: 08 00 88 00
2023-10-25,18:18:30,Warnung,192.168.121.229,console,1,2023-10-25T18:18:30.718189+2:00 ems-esp telegram - - - 006+20:40:24.394 W 46263: Incomplete Rx: 90 00 10 00 88 00 08 00 89 00 B4 00 95 00 15 00 88 00 08 00
2023-10-25,18:18:30,Warnung,192.168.121.229,console,1,2023-10-25T18:18:30.595005+2:00 ems-esp telegram - - - 006+20:40:24.378 W 46262: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:29,Warnung,192.168.121.229,console,1,2023-10-25T18:18:29.912439+2:00 ems-esp telegram - - - 006+20:40:23.596 W 46261: Incomplete Rx: 90 00 10 00 95 00 15 00 88 00 08 00 8C 00 AA 00 2A 00 88 00 08 00 89 00
2023-10-25,18:18:29,Warnung,192.168.121.229,console,1,2023-10-25T18:18:29.627360+2:00 ems-esp telegram - - - 006+20:40:23.411 W 46260: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:29,Warnung,192.168.121.229,console,1,2023-10-25T18:18:29.363858+2:00 ems-esp telegram - - - 006+20:40:23.039 W 46259: Incomplete Rx: BA 00 88 00 08 00 8B 00 88 00 08 00 C2 00 90 00
2023-10-25,18:18:28,Warnung,192.168.121.229,console,1,2023-10-25T18:18:28.483827+2:00 ems-esp telegram - - - 006+20:40:22.158 W 46258: Incomplete Rx: AA 00 2A 00 88 00 08 00 88 00 08 00 8C 00 8B 00 88 00 08 00
2023-10-25,18:18:28,Warnung,192.168.121.229,console,1,2023-10-25T18:18:28.319664+2:00 ems-esp telegram - - - 006+20:40:22.101 W 46257: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:28,Warnung,192.168.121.229,console,1,2023-10-25T18:18:28.186398+2:00 ems-esp telegram - - - 006+20:40:21.971 W 46256: Incomplete Rx: 88 00 08 00 88
2023-10-25,18:18:27,Warnung,192.168.121.229,console,1,2023-10-25T18:18:27.927297+2:00 ems-esp telegram - - - 006+20:40:21.723 W 46255: Incomplete Rx: B8 00 90 00 10 00 88 00 08 00 95 00 15 00 C0 00 AA
2023-10-25,18:18:27,Warnung,192.168.121.229,console,1,2023-10-25T18:18:27.554897+2:00 ems-esp telegram - - - 006+20:40:21.332 W 46254: Incomplete Rx: 08 00 88 00
2023-10-25,18:18:27,Warnung,192.168.121.229,console,1,2023-10-25T18:18:27.375473+2:00 ems-esp telegram - - - 006+20:40:21.050 W 46253: Incomplete Rx: AA 00 2A 00 88 00 08 00 89 00 93 00 88 00 08 00 88 00 08 00
2023-10-25,18:18:26,Warnung,192.168.121.229,console,1,2023-10-25T18:18:26.899892+2:00 ems-esp telegram - - - 006+20:40:20.684 W 46252: Incomplete Rx: 88 00 08 00 88
2023-10-25,18:18:26,Warnung,192.168.121.229,console,1,2023-10-25T18:18:26.791314+2:00 ems-esp telegram - - - 006+20:40:20.460 W 46251: Incomplete Rx: 88 00 08 00 8B 00 88 00 08 00 EF 00 90 00 10 00 88 00 08 00
2023-10-25,18:18:26,Warnung,192.168.121.229,console,1,2023-10-25T18:18:26.631315+2:00 ems-esp telegram - - - 006+20:40:20.412 W 46250: Incomplete Rx: 2A 00 88 00 08
2023-10-25,18:18:26,Warnung,192.168.121.229,console,1,2023-10-25T18:18:26.577886+2:00 ems-esp telegram - - - 006+20:40:20.355 W 46249: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:26,Warnung,192.168.121.229,console,1,2023-10-25T18:18:26.453079+2:00 ems-esp telegram - - - 006+20:40:20.234 W 46248: Incomplete Rx: 08 00 88 00
2023-10-25,18:18:26,Warnung,192.168.121.229,console,1,2023-10-25T18:18:26.320680+2:00 ems-esp telegram - - - 006+20:40:20.104 W 46247: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:26,Warnung,192.168.121.229,console,1,2023-10-25T18:18:26.224606+2:00 ems-esp telegram - - - 006+20:40:19.898 W 46246: Incomplete Rx: 10 00 88 00 08 00 89 00 A7 00 95 00 15 00 AA 00 2A 00 88 00 08 00
2023-10-25,18:18:26,Warnung,192.168.121.229,console,1,2023-10-25T18:18:26.061236+2:00 ems-esp telegram - - - 006+20:40:19.845 W 46245: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:25,Warnung,192.168.121.229,console,1,2023-10-25T18:18:25.262447+2:00 ems-esp telegram - - - 006+20:40:18.941 W 46244: Incomplete Rx: 2A 00 88 00 08 00 88 00 08 00 E3 00 8B 00 88 00 08 00 89
2023-10-25,18:18:25,Warnung,192.168.121.229,console,1,2023-10-25T18:18:24.963184+2:00 ems-esp telegram - - - 006+20:40:18.746 W 46243: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:24,Warnung,192.168.121.229,console,1,2023-10-25T18:18:24.760920+2:00 ems-esp telegram - - - 006+20:40:18.542 W 46242: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:24,Warnung,192.168.121.229,console,1,2023-10-25T18:18:24.696870+2:00 ems-esp telegram - - - 006+20:40:18.368 W 46241: Incomplete Rx: 9B 00 90 00 10 00 95 00 15 00 88 00 08 00 A3 00 AA 00 2A 00 88 00 08 00
2023-10-25,18:18:24,Warnung,192.168.121.229,console,1,2023-10-25T18:18:24.514410+2:00 ems-esp telegram - - - 006+20:40:18.298 W 46240: Incomplete Rx: 08 00 88 00
2023-10-25,18:18:24,Warnung,192.168.121.229,console,1,2023-10-25T18:18:24.301657+2:00 ems-esp telegram - - - 006+20:40:18.078 W 46239: Incomplete Rx: 88 00 08 00
2023-10-25,18:18:24,Warnung,192.168.121.229,console,1,2023-10-25T18:18:24.124002+2:00 ems-esp telegram - - - 006+20:40:17.802 W 46238: Incomplete Rx: AA 00 2A 00 88 00 08 00 89 00 8E 00 88 00 08 00 8B 00 88 00

1 reply

MichaelDvP Oct 25, 2023
Maintainer

Tested again with my BBQKees S32S3 and the bin from my GH, upload via webpage works.
What have you used for usb-upload? What does system status show for Application and Filesystem?

philipherbert · 2023-10-25T16:46:26Z

philipherbert
Oct 25, 2023
Author

I will still need to compare witht the Display on the boiler.

2 replies

MichaelDvP Oct 25, 2023
Maintainer

undefined instead of V look odd, could you reload the page in browser, may be old script in cache?

philipherbert Oct 25, 2023
Author

reload removed 'undefined' .

philipherbert · 2023-10-25T16:57:14Z

philipherbert
Oct 25, 2023
Author

as I wrote, No need for USB this time.
I might not have waited 20 minutes last time I tried one of your testbuilds.

After aprox 20 minutes the device was online again.
No idea why it now takes so long to reconnect after reboot/upload.
I hope you can see something in the log.

23-10-25,18:35:12,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:17.044 I 642: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:12,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:14.038 W 641: WiFi disconnected. Reason: assoc leave (8)
2023-10-25,18:35:12,Info,192.168.121.229,kern,1,"- ems-esp emsesp - - - 000+00:16:14.038 I 640: WiFi connection dropped, stopping NTP"
2023-10-25,18:35:12,Warnung,192.168.121.229,kern,1,- ems-esp emsesp - - - 000+00:16:11.031 W 639: WiFi disconnected. Reason: assoc leave (8)

1 reply

MichaelDvP Oct 25, 2023
Maintainer

Hm, tried an old Liligo S3 to update from 3.1.x: did not connect, serial terminal shows repeated auth failed and AP does not come up. I've used the button-long-press to reset to factory, then AP comes up. I think this is something in arduino 2.0.14 changed against <=2.0.13, but will check.

philipherbert · 2023-10-25T17:04:49Z

philipherbert
Oct 25, 2023
Author

btw. you call it 'Alert Module'
Buderus calls it 'Extension Module'. I believe Extension Module is a better description, because of its multi purpose functionality. (depending on dip setting / connected terminals)

5 replies

MichaelDvP Oct 25, 2023
Maintainer

Ah, this explains the device-id 0x15. In old EMS system EM10 was on 0x12 and was called Alert-module (or Error-Module), 0x15 was pump module PM10. So now we have Extension Module on 0x15 called EM10/100. Needs new mapping and lot of renaming, thats some work and needs time.

philipherbert Oct 25, 2023
Author

Alert it one of the functions, Pump output is also possible, Have you seen the manual ? I have uploaded a link to the official download.

philipherbert Oct 25, 2023
Author

btw: only one em100 is allowed. Only when setting to dip 10 (Energy and Efficiency Calculation) a second EM100 is permitted. I have not found a description for Mode 10.

When operating a seperator, a temperature sensor needs to be connected to this seperator when operated in EMS Bus. Only with EMS+ the Boilers temperatur sensor connected to the seperator can be used.

MichaelDvP Oct 26, 2023
Maintainer

I have changed the module to extension and fixed the connection issue. Please check if displayed correctly.

philipherbert · 2023-10-25T17:20:02Z

philipherbert
Oct 25, 2023
Author

on the diagnostic page of the boilers UI, the raw voltage of the input is also displayed.
You will want me to trace the other modes (dip settings) also ?

0 replies

philipherbert · 2023-10-26T17:06:02Z

philipherbert
Oct 26, 2023
Author

let use start with really good news: connection to wifi was never as fast as this time !
Changes to settings min/max Volt + Temperature are correct.
Boiler display shows raw value for Voltage Input - that would be nice here also.
IO1 Output is called PowerMonitorOutput and displayed on the boiler as percent value, you show it as binary on 13% you show some binary as IO01

I have changed some settings and collected a full log. Also I will upload screenshots of the boiler display (set to english) for this module.
Even if not needed, I could connect T0 to get a value in the trace.

ems-esp:$ change to 5.5V input

ems-esp:$ ems-esp:$ 000+00:22:55.567 N 125: [emsesp] extension(0x15) -B-> All(0x00), EM100InputMessage(0x0938), data: 2F (offset 1)
ems-esp:$ 000+00:22:55.750 N 126: [emsesp] extension(0x15) -B-> All(0x00), EM100MonitorMessage(0x0939), data: 2C (offset 1)
ems-esp:$ 000+00:22:56.145 N 127: [emsesp] extension(0x15) -W-> boiler(0x08), ?(0xD2), data: 2C (offset 1)
ems-esp:$ 000+00:22:56.589 N 128: [emsesp] extension(0x15) -B-> All(0x00), EM100MonitorMessage(0x0939), data: 32 (offset 1)
ems-esp:$ 000+00:22:57.224 N 129: [emsesp] extension(0x15) -W-> boiler(0x08), ?(0xD2), data: 32 (offset 1)
ems-esp:$ 000+00:22:59.040 N 130: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorFastPlus(0xE4), data: 10 20 2D 2D 00 C8 3A 02 7A 64 0D 03 00 02 9F 00 00 02 5F 00 81 0D 00 02 9F 02 7A
ems-esp:$ 000+00:22:59.215 N 131: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorFastPlus(0xE4), data: 00 04 47 00 00 0D 64 (offset 35)
ems-esp:$ 000+00:22:59.406 N 132: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorSlowPlus2(0xE3), data: 01 00 00 00 00 00 04 00 00 00 00 02 79 0D 64 46 00 32 00 00
ems-esp:$ 000+00:22:59.618 N 133: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorWWPlus(0xE9), data: 35 01 F8 01 F8 00 00 00 00 46 3C 00 00 00 00 1C E7 00 02 EA 00 00 00 35 02 00
ems-esp:$ 000+00:23:00.211 N 134: [emsesp] Me(0x0B) -R-> boiler(0x08), UBATotalUptime(0x14), length: 0x1B
ems-esp:$ 000+00:23:00.225 N 135: [emsesp] boiler(0x08) -W-> Me(0x0B), UBATotalUptime(0x14), data: 01 09 94
ems-esp:$ 000+00:23:00.437 N 136: [emsesp] Me(0x0B) -R-> boiler(0x08), UBAParametersPlus(0xE6), length: 0x1B
ems-esp:$ 000+00:23:00.488 N 137: [emsesp] boiler(0x08) -W-> Me(0x0B), UBAParametersPlus(0xE6), data: 01 46 00 52 64 0C 00 00 06 FA 0A 02 06 64 32 00 00 00 01 3A 00 00 00 00 01 01 00
ems-esp:$ 000+00:23:00.744 N 138: [emsesp] Me(0x0B) -R-> boiler(0x08), UBAParametersPlus(0xE6), length: 0x1B (offset 27)
ems-esp:$ 000+00:23:00.765 N 139: [emsesp] boiler(0x08) -W-> Me(0x0B), UBAParametersPlus(0xE6), data: 00 06 0D 78 00 00 00 00 00 32 00 00 1E 0C (offset 30)
ems-esp:$ 000+00:23:00.961 N 140: [emsesp] Me(0x0B) -R-> boiler(0x08), UBAParameterWWPlus(0xEA), length: 0x1B
ems-esp:$ 000+00:23:00.998 N 141: [emsesp] boiler(0x08) -W-> Me(0x0B), UBAParameterWWPlus(0xEA), data: 00 00 00 00 00 01 35 FB 00 0C 00 02 46 00 00 00 3C 3C 28 23 50 29 00 00 00 00 00
ems-esp:$ 000+00:23:01.224 N 142: [emsesp] Me(0x0B) -R-> boiler(0x08), UBAParameterWWPlus(0xEA), length: 0x1B (offset 27)
ems-esp:$ 000+00:23:01.227 N 143: [emsesp] boiler(0x08) -W-> Me(0x0B), UBAParameterWWPlus(0xEA), data: (offset 27)
ems-esp:$ 000+00:23:01.495 N 144: [emsesp] Me(0x0B) -R-> thermostat(0x10), HPMode(0x0291), length: 0x19
ems-esp:$ 000+00:23:01.532 N 145: [emsesp] thermostat(0x10) -W-> Me(0x0B), HPMode(0x0291), data: 00 00 00 00 00 00
ems-esp:$ 000+00:23:01.730 N 146: [emsesp] Me(0x0B) -R-> thermostat(0x10), HPMode(0x0292), length: 0x19
ems-esp:$ 000+00:23:01.766 N 147: [emsesp] thermostat(0x10) -W-> Me(0x0B), HPMode(0x0292), data: 00 00 00 00 00 00
ems-esp:$ 000+00:23:02.003 N 148: [emsesp] Me(0x0B) -R-> thermostat(0x10), HPMode(0x0293), length: 0x19
ems-esp:$ 000+00:23:02.038 N 149: [emsesp] thermostat(0x10) -W-> Me(0x0B), HPMode(0x0293), data: 00 00 00 00 00 00
ems-esp:$ 000+00:23:02.293 N 150: [emsesp] Me(0x0B) -R-> thermostat(0x10), HPMode(0x0294), length: 0x19
ems-esp:$ 000+00:23:02.329 N 151: [emsesp] thermostat(0x10) -W-> Me(0x0B), HPMode(0x0294), data: 00 00 00 00 00 00
ems-esp:$ 000+00:23:02.529 N 152: [emsesp] Me(0x0B) -R-> thermostat(0x10), RC300WWmode(0x02F5), length: 0x19
ems-esp:$ 000+00:23:02.599 N 153: [emsesp] thermostat(0x10) -W-> Me(0x0B), RC300WWmode(0x02F5), data: 03 00 01 02 00 00 08 01 00 08 04 00 00 00 00 00 00 00 00 00 01
ems-esp:$ 000+00:23:02.829 N 154: [emsesp] Me(0x0B) -R-> thermostat(0x10), RC300OutdoorTemp(0x023A), length: 0x19
ems-esp:$ 000+00:23:02.855 N 155: [emsesp] thermostat(0x10) -W-> Me(0x0B), RC300OutdoorTemp(0x023A), data: 00 14
ems-esp:$ 000+00:23:03.120 N 156: [emsesp] Me(0x0B) -R-> thermostat(0x10), RC300Settings(0x0240), length: 0x19
ems-esp:$ 000+00:23:03.197 N 157: [emsesp] thermostat(0x10) -W-> Me(0x0B), RC300Settings(0x0240), data: FF 00 05 00 00 00 00 00 FF 02 F8 06 FF 00 00 14 00 32 00 00 00 FF 00 01
ems-esp:$ 000+00:23:03.396 N 158: [emsesp] Me(0x0B) -R-> thermostat(0x10), RC300Settings(0x0240), length: 0x19 (offset 24)
ems-esp:$ 000+00:23:03.419 N 159: [emsesp] thermostat(0x10) -W-> Me(0x0B), RC300Settings(0x0240), data: (offset 24)
ems-esp:$ 000+00:23:03.656 N 160: [emsesp] Me(0x0B) -R-> solar(0x2A), SM100wwCirc(0x07A5), length: 0x19
ems-esp:$ 000+00:23:03.695 N 161: [emsesp] solar(0x2A) -W-> Me(0x0B), SM100wwCirc(0x07A5), data: 00 03 0A 03 FF 1E 32
ems-esp:$ 000+00:23:03.952 N 162: [emsesp] Me(0x0B) -R-> solar(0x2A), SM100wwParam(0x07A6), length: 0x19
ems-esp:$ 000+00:23:04.045 N 163: [emsesp] solar(0x2A) -W-> Me(0x0B), SM100wwParam(0x07A6), data: FF 05 0F 5F 19 01 3C 3C 3C 34 2D 12 41 01 3C 1E 03 07 3C 01 08 00 05
ems-esp:$ 000+00:23:04.240 N 164: [emsesp] Me(0x0B) -R-> solar(0x2A), SM100wwKeepWarm(0x07AE), length: 0x19
ems-esp:$ 000+00:23:04.267 N 165: [emsesp] solar(0x2A) -W-> Me(0x0B), SM100wwKeepWarm(0x07AE), data: 00 0F 0F
ems-esp:$ 000+00:23:04.497 N 166: [emsesp] Me(0x0B) -R-> solar(0x2A), SM100wwStatus2(0x07E0), length: 0x19
ems-esp:$ 000+00:23:04.571 N 167: [emsesp] solar(0x2A) -W-> Me(0x0B), SM100wwStatus2(0x07E0), data: 00 00 00 00 00 00 00 00 03 00 00 00 00 00 00 03 03 03 03
ems-esp:$ 000+00:23:04.835 N 168: [emsesp] Me(0x0B) -R-> extension(0x15), EM100SetMessage(0x0935), length: 0x19
ems-esp:$ 000+00:23:04.872 N 169: [emsesp] extension(0x15) -W-> Me(0x0B), EM100SetMessage(0x0935), data: 00 00 64 50 14
ems-esp:$ 000+00:23:05.067 N 170: [emsesp] Me(0x0B) -R-> boiler(0x08), UBAMonitorFastPlus(0xE4), length: 0x02 (offset 25)
ems-esp:$ 000+00:23:05.077 N 171: [emsesp] boiler(0x08) -W-> Me(0x0B), UBAMonitorFastPlus(0xE4), data: 02 7A (offset 25)
ems-esp:$ 000+00:23:05.294 N 172: [emsesp] Me(0x0B) -R-> boiler(0x08), UBAMonitorFastPlus(0xE4), length: 0x02 (offset 23)
ems-esp:$ 000+00:23:05.319 N 173: [emsesp] boiler(0x08) -W-> Me(0x0B), UBAMonitorFastPlus(0xE4), data: 02 9F (offset 23)
ems-esp:$ 000+00:23:06.241 N 174: [emsesp] thermostat(0x10) -B-> All(0x00), RCTime(0x06), data: 17 0A 12 1A 35 22 03 01 10 FF 00
ems-esp:$ 000+00:23:07.730 N 175: [emsesp] extension(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
ems-esp:$ 000+00:23:09.027 N 176: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorFastPlus(0xE4), data: 10 20 2D 2D 00 C8 3A 02 79 64 0D 03 00 02 9F 00 00 02 5F 00 81 0D 00 02 9F 02 79
ems-esp:$ 000+00:23:09.202 N 177: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorFastPlus(0xE4), data: 00 04 46 00 00 0D 64 (offset 35)
ems-esp:$ 000+00:23:09.392 N 178: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorSlowPlus2(0xE3), data: 01 00 00 00 00 00 04 00 00 00 00 02 79 0D 64 46 00 32 00 00
ems-esp:$ 000+00:23:09.634 N 179: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorWWPlus(0xE9), data: 35 01 F8 01 F8 00 00 00 00 46 3C 00 00 00 00 1C E7 00 02 EA 00 00 00 35 02 00
ems-esp:$ 000+00:23:17.366 N 180: [emsesp] solar(0x2A) -B-> All(0x00), ?(0x07A9), data: 2F
ems-esp:$ 000+00:23:19.077 N 181: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorFastPlus(0xE4), data: 10 20 2D 2D 00 C8 3A 02 7A 64 0D 03 00 02 9F 00 00 02 5F 00 81 0D 00 02 9F 02 7A
ems-esp:$ 000+00:23:19.254 N 182: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorFastPlus(0xE4), data: 00 04 47 00 00 0D 64 (offset 35)
ems-esp:$ 000+00:23:19.443 N 183: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorSlowPlus2(0xE3), data: 01 00 00 00 00 00 04 00 00 00 00 02 7A 0D 64 46 00 32 00 00
ems-esp:$ 000+00:23:19.648 N 184: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorWWPlus(0xE9), data: 35 01 F8 01 F8 00 00 00 00 46 3C 00 00 00 00 1C E7 00 02 EA 00 00 00 35 02 00
ems-esp:$ 000+00:23:27.785 N 185: [emsesp] extension(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
ems-esp:$ 000+00:23:29.016 N 186: [emsesp] boiler(0x08) -B-> All(0x00), UBAMonitorFastPlus(0xE4), data: 10 20 2D 2D 00 C8 3A 02 7A 64 0D 03 00 02 A0 00 00 02 5F 00 81 0D 00 02 9F 02 7A
ems-esp:$

0 replies

philipherbert · 2023-10-26T19:14:30Z

philipherbert
Oct 26, 2023
Author

tried to set writable parameters via ems-esp ui -> working, Decimal values for voltage not possible (example max :9,5V), When set via BoilerUI, the value is correct in ems esp entities. Is there a range checking for setting any values ?

EM100 seems to be missing in mqtt..

0 replies

MichaelDvP · 2023-10-27T08:52:28Z

MichaelDvP
Oct 27, 2023
Maintainer

Fixed the mqtt. For the voltage setting, please log while setting a voltage via ems-esp webui. I have set no limits, we have to see twhat the device gets and replys.

0 replies

philipherbert · 2023-11-05T12:06:24Z

philipherbert
Nov 5, 2023
Author

this value is is called IO1 Power Monitor output (27 % at time of trace in Boiler display), currently not yet in EMS-ESP for this module.

extension(0x15) -B-> All(0x00), ?(0x0936), data: 1B (offset 5)

====
Voltage setting from EMS (for MIN /MAX) works and is correct/identical to the boiler(

Volttage Input of EM100 (not Entity on EMS-ESP for this)
Can you find the following Information from Diag Page:
Input 0..10V: currently 6.7Volt ?

000+17:41:03.421 N 1858: [emsesp] extension(0x15) -B-> All(0x00), ?(0x0936), data: 25 (offset 5)
000+17:41:14.563 N 1859: [emsesp] Me(0x0B) -R-> extension(0x15), EM100SetMessage(0x0935), length: 0x19
000+17:41:14.600 N 1860: [emsesp] extension(0x15) -W-> Me(0x0B), EM100SetMessage(0x0935), data: 00 00 64 50 14
000+17:41:14.703 N 1861: [emsesp] extension(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
000+17:41:14.886 N 1862: [emsesp] extension(0x15) -B-> All(0x00), ?(0x0936), data: 26 (offset 5)
000+17:41:23.150 N 1863: [emsesp] extension(0x15) -B-> All(0x00), ?(0x0936), data: 27 (offset 5)
000+17:41:33.319 N 1864: [emsesp] extension(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
000+17:41:43.080 N 1865: [emsesp] extension(0x15) -B-> All(0x00), ?(0x0936), data: 28 (offset 5)
000+17:41:53.406 N 1866: [emsesp] extension(0x15) -B-> All(0x00), ?(0x9C), data: 00 (offset 5)
000+17:41:53.586 N 1867: [emsesp] extension(0x15) -W-> boiler(0x08), ?(0xD2), data: 3A 64 (offset 1)
000+17:41:53.610 N 1868: [emsesp] extension(0x15) -W-> boiler(0x08), ?(0xE2), data: 01
000+17:41:53.649 N 1869: [emsesp] extension(0x15) -B-> All(0x00), ?(0x0936), data: 00 00 00 00 28 00 (offset 1)
000+17:41:54.088 N 1870: [emsesp] extension(0x15) -B-> All(0x00), EM100TempMessage(0x0937), data: 80 00
000+17:41:54.274 N 1871: [emsesp] extension(0x15) -B-> All(0x00), EM100InputMessage(0x0938), data: 01 43
000+17:41:54.718 N 1872: [emsesp] extension(0x15) -B-> All(0x00), EM100MonitorMessage(0x0939), data: 64 3A 00 00
000+17:41:54.925 N 1873: [emsesp] extension(0x15) -B-> All(0x00), EM100ConfigMessage(0x093A), data: 00 00 00 00 00 00 00 00 00 03 01

===
what you call set temp is called Supply Setpoint in the Boiler
Boiler display show: Set Power for Heat appl. 100 % (not in ems-esp for this module)
OE1 error display: off (not in ems-esp)
OE1 liquid gas valve: OFF or ON (depending on boiler active ?) in ems-esp alwas 1%
IE0 Pump Error: not in EMS-ESP

3 replies

philipherbert Nov 5, 2023
Author

I have found the values and added them as custom -working.

01 Power Monitor Output, identical to boiler current power, used for an 0-10V Output of the module

proddy Nov 11, 2023
Maintainer

I can see @MichaelDvP added the input voltage to dev2. Do we need the % as well to complete this for the next release?

philipherbert Nov 13, 2023
Author

Input voltage is not in the .test8a (yet). The % is identically to the current power of the boiler, As it is on the EM100 diagnostic page and broadcasted by the module, it may be reasonable to add it. At least users see the same value in EMS-ESP as they see on the diagnostic screen of the boiler for this modules (in dip-mode 3). Output IO1 ist something wrong. I suggest removing it until it is fixed.

philipherbert · 2023-11-05T12:16:38Z

philipherbert
Nov 5, 2023
Author

correction: OE1 liquid gas valve NOT related to boiler running state in Boiler Display

0 replies

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Buderus EM100 external flow temperature #1315

{{title}}

Replies: 17 comments 14 replies

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

Select a reply

Buderus EM100 external flow temperature #1315

philipherbert Oct 2, 2023

Replies: 17 comments · 14 replies

MichaelDvP Oct 3, 2023 Maintainer

philipherbert Oct 16, 2023 Author

philipherbert Oct 16, 2023 Author

MichaelDvP Oct 18, 2023 Maintainer

philipherbert Oct 18, 2023 Author

philipherbert Oct 18, 2023 Author

philipherbert Oct 20, 2023 Author

MichaelDvP Oct 25, 2023 Maintainer

philipherbert Oct 25, 2023 Author

philipherbert Oct 25, 2023 Author

MichaelDvP Oct 25, 2023 Maintainer

philipherbert Oct 25, 2023 Author

MichaelDvP Oct 25, 2023 Maintainer

philipherbert Oct 25, 2023 Author

philipherbert Oct 25, 2023 Author

MichaelDvP Oct 25, 2023 Maintainer

philipherbert Oct 25, 2023 Author

MichaelDvP Oct 25, 2023 Maintainer

philipherbert Oct 25, 2023 Author

philipherbert Oct 25, 2023 Author

philipherbert Oct 25, 2023 Author

MichaelDvP Oct 26, 2023 Maintainer

philipherbert Oct 25, 2023 Author

philipherbert Oct 26, 2023 Author

philipherbert Oct 26, 2023 Author

MichaelDvP Oct 27, 2023 Maintainer

philipherbert Nov 5, 2023 Author

philipherbert Nov 5, 2023 Author

proddy Nov 11, 2023 Maintainer

philipherbert Nov 13, 2023 Author

philipherbert Nov 5, 2023 Author

philipherbert
Oct 2, 2023

Replies: 17 comments 14 replies

MichaelDvP
Oct 3, 2023
Maintainer

philipherbert
Oct 16, 2023
Author

philipherbert
Oct 16, 2023
Author

MichaelDvP Oct 18, 2023
Maintainer

philipherbert
Oct 18, 2023
Author

philipherbert
Oct 18, 2023
Author

philipherbert
Oct 20, 2023
Author

MichaelDvP Oct 25, 2023
Maintainer

philipherbert
Oct 25, 2023
Author

philipherbert
Oct 25, 2023
Author

MichaelDvP Oct 25, 2023
Maintainer

philipherbert
Oct 25, 2023
Author

MichaelDvP Oct 25, 2023
Maintainer

philipherbert Oct 25, 2023
Author

philipherbert
Oct 25, 2023
Author

MichaelDvP Oct 25, 2023
Maintainer

philipherbert
Oct 25, 2023
Author

MichaelDvP Oct 25, 2023
Maintainer

philipherbert Oct 25, 2023
Author

philipherbert Oct 25, 2023
Author

philipherbert Oct 25, 2023
Author

MichaelDvP Oct 26, 2023
Maintainer

philipherbert
Oct 25, 2023
Author

philipherbert
Oct 26, 2023
Author

philipherbert
Oct 26, 2023
Author

MichaelDvP
Oct 27, 2023
Maintainer

philipherbert
Nov 5, 2023
Author

philipherbert Nov 5, 2023
Author

proddy Nov 11, 2023
Maintainer

philipherbert Nov 13, 2023
Author

philipherbert
Nov 5, 2023
Author